2013 SUZUKI ALTO clock

7-28
INSPECTION AND MAINTENANCE
53MH0-74E
Side Turn Signal Light
53M-09-050
Pull down the lens by using a flat blade
screwdriver covered with a soft cloth as
shown. The bulb can be removed by sim-
ply pulling it out. Then remove the bulb.
Install a new bulb in the reverse order.
Other General Lights
Bulb holder
53M-09-051
(1) Removal
(2) Installation
To remove a bulb holder from a light hous-
ing, turn the holder counterclockwise and
pull it out. To install the holder, push the
holder in and turn it clockwise.
Bulb
53M-09-052
(3) Removal
(4) Installation
There are two types of bulb, “Full glass
type” (1) and “Glass/metal type” (2).
To remove and install a full glass type bulb
(1), simply pull out or push in the bulb.
To remove a glass metal type bulb (2) from
a bulb holder, push in the bulb and turn it
counterclockwise. To install a new bulb,
push it in and turn it clockwise.
You can access the individual bulb or bulb
holders as follows.
Front turn signal light (1)
Front position light (2)
ALTO 800
53MM07001
ALTO K10
53M-09-054
EXAMPLE
EXAMPLE
EXAMPLE(1) (2)
EXAMPLE
EXAMPLE

8-1
EMERGENCY SERVICE
53MH0-74E
Tire Changing Tool
53MH0801
74LHT0807
The jack (1) is stowed below the luggage
compartment board as shown in the above
illustration.The jack handle and wheel brace are
stowed in the storage bag.
68KH091
To remove the spare tire, turn its bolt (1)
counterclockwise and remove it.
To remove the jack, remove the spare tire
and turn the jacks shaft counterclockwise
and pull the jack out of the storage bracket.
To stow the jack, place it in the storage
bracket and turn the shaft clockwise until
the jack is securely held in place.
Jacking Instructions
52KM119
1) Place the vehicle on level, hard ground.
2) Set the parking brake firmly and shift
into “R” (Reverse) if your vehicle has a
manual transaxle.
EXAMPLE
EXAMPLE
WA R N I N G
After using the tire changing tools, be
sure to stow them securely or they
can cause injury if an accident
occurs.
(1)
CAUTION
The jack should be used only to
change wheels. It is important to read
the jacking instructions in this sec-
tion before attempting to use the
jack.
WA R N I N G
• Be sure to shift into “R” (Reverse)
when you jack up the vehicle.
• Never jack up the vehicle with the
transaxle in “N” (Neutral). Other-
wise, unstable jack may cause an
accident.
EXAMPLE

8-2
EMERGENCY SERVICE
53MH0-74E
3) Turn on the hazard warning flasher if
your vehicle is near traffic.
4) Block the front and rear of the wheel
diagonally opposite of the wheel being
lifted.
5) Place the spare wheel near the wheel
being lifted as shown in the illustration
in case that the jack slips.
54G253
53MH080353MH0804
6) Position the jack vertically and raise the
jack by turning the jack handle clock-
wise until the jack head groove fits
around the jacking bar beneath the
vehicle body. See illustrations.
7) Continue to raise the jack slowly and
smoothly until the tire clears the
ground. Do not raise the vehicle more
than necessary.
To Raise the Vehicle with a Garage Jack
Apply the garage jack to one of the
points indicated below.
EXAMPLE
EXAMPLE
EXAMPLEWA R N I N G
• Use the jack only to change wheels
on level, hard ground.
• Never jack up the vehicle on an
inclined surface.
• Never raise the vehicle with the
jack in a location other than the
specified jacking point (shown in
the illustration) near the wheel to
be changed.
• Make sure that the jack is raised at
least 51 mm (2 inches) before it
contacts the suspension arm boss.
Use of the jack when it is within 51
mm (2 inches) of being fully col-
lapsed may result in failure of the
jack.
• Never get under the vehicle when it
is supported by the jack.
• Never run the engine when the
vehicle is supported by the jack
and never allow passengers to
remain in the vehicle.

8-8
EMERGENCY SERVICE
53MH0-74E
Warning Triangle
53M-10-014
In case of vehicle break-down or during
emergency stopping, where, your vehicle
could become a potential traffic hazard,
keep the warning triangle, provided with
your vehicle, on the road free from any
obstacles behind your vehicle so as to
warn the approaching traffic, at an approxi-
mate distance of 50-100 m. The reflecting
side of the triangle should face the on com-
ing traffic. Please activate the hazard
warning lamps before alighting the vehicle
to keep the warning triangle.
53M-10-015
Remove the warning triangle carefully
from the cover as shown by arrow 1.
Open both the reflector arms as shown
by arrow and lock the arms with each
other with the clip provided in the right
arm. Open the bottom stand in counter
clock-wise direction as shown by arrow
3. Position the warning triangle behind
the vehicle on a plain surface.
Reverse the removal procedure for keep-
ing inside the cover.
53M-10-016
EXAMPLE
EXAMPLE
EXAMPLE