2013 SSANGYONG TURISMO key

08-118610-11
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is
changed to 2 from 1 during receiving the malfunction signal (3) from the rain sensor (while the
ignition key is in “ON” position and the wiper switch is in “AUTO” position). Also, the wiper
relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is changed to
2 from 1 during receiving the ground fixed or IGN fixed signal from the rain sensor. 3)
The wiper relay (LO) is turned on and the wiper motor runs one cycle when the wiper sensitivity is
changed to 3 from 4 during receiving the malfunction signal (2) from the rain sensor (while the
ignition key is in “ON” position and the wiper switch is in “AUTO” position). 2)

09-4
2. CAUTIONS
The parking aid system is just a supplemental device to help your parking.
Always keep the safety precautions.
Do not press or shock the sensors by hitting or using a high-pressure water gun while washing,
since it may damage the sensors.
If the system is in normal operating condition, a short beep sounds when the shift lever is moved
into "R" position with the ignition key "ON".
If the system is defective, the warning buzzer sounds for 3 seconds when moving the gear shift
lever to “R” position with the ignition ON. Be careful not to confuse this and the parking aid
alarm (in 50 cm). 1.
2.
3.
4.
5.
- Note that the display does not show everything in the rear area. Always check
nobody, especially animals and children, is behind the vehicle when parking or
reversing.
- If you can not properly check the vehicle behind, get out of the vehicle and then
visually check it.
The parking aid system will not work or improperly work under following cases: ▶
1) Certain obstacles that sensors can not detect
Thin and narrow objects, such as wires, ropes, chains
Cotton, sponge, clothes, snow; that absorb ultrasonic waves
Obstacles lower than the bumper (ex. drain ditch or mud puddle) -
-
-
2) Not defective but improperly working
When the sensing portion is frozen (operates normally after thawed)
When the sensing portion is covered by rain, water drops, snow or mud (operates normally after
cleaned)
When receiving other ultrasonic signals (metal sound or air braking noises from heavy commercial
vehicles)
When a high-power radio is turned on -
-
-
-
3) Narrowed sensing area
When the sensing portion is partially covered by snow or mud (operates normally after cleaned)
Surrounding temperature of sensor is too high (approx. over 80°C) or too low
(approx. below -30°C) -
-
4) Not defective but may cause malfunction
When driving on the rough roads, gravel road, hill and grass
When the bumper height is changed due to heavy load
When the sensing portion is frozen
When the sensing portion is covered by rain, water drops, snow or mud
When receiving other ultrasonic signals (metal sound or air braking noises from heavy commercial
vehicles)
When a high-power radio is turned on
When some accessories are attached in detecting ranges -
-
-
-
-
-
-

11-158910-05
3) Audio Setting
If you press the "SETUP" button, the text "EQ" appears in the display. When you turn the volume
control dial, the texts appear in the following order: "EQ" ↔ "TONE" ↔ "BT".
When the specific text appears, press the ENTER button to set the entry. However, if no choice has
been made within 5 seconds, the Setting mode is quit automatically.
Press SET button to enter the Setting mode. “EQ”, “TONE” and “BT” appear on the display.
Rotate TUNE dial to select the “EQ” menu, then press ENTER button.
Rotate TUNE dial to select the desired EQ style, then press ENTER button. 1.
2.
3.Selecting the Equalizer style ▶
If no key input is made for 5 seconds, the current status is saved and the Setting mode is quit.
*If no key input is made for 5 seconds, the current status is saved and the Setting mode is quit.
*By rotating the TUNE dial, you can select one of the following EQ Styles.
EQ OFF ↔ POP ↔ ROCK ↔ COUNTRY ↔ VOICE↔ JAZZ ↔ CLASSIC ↔ .... -
By rotating the TUNE dial, you can select one of the following Tone Control items.
BASS ↔ MIDDLE ↔ TREBLE ↔ BALANCE ↔FADER ↔ PREVIOUS ↔ .... - Press SET button to enter the Setting mode. “EQ”, “TONE” and “BT” a
ppear on the display
Rotate TUNE dial to select the “TONE” menu, then press ENTER button.
Rotate TUNE dial to select the desired Tone control item, then press ENTER button. 1.
2.
3.Setting the sound (TONE) ▶
Rotate TUNE dial to adjust the value of the level or balance, then press ENTER button. 4.
BASS: adjust the bass sound level (-7 to +7).
MIDDLE: adjust the treble sound level (-7 to +7).
TREBLE: adjust the treble sound level (-7 to +7).
BALANCE: adjust the sound balance between the right and left speakers (LEFT15 to RIGHT15).
FADER: adjust the sound fade between the front and rear speakers (FRONT15 to REAR15).
PREVIOUS: return to the TONE menu. -
-
-
-
-
-

11-16
By rotating VOLUME dial, you can select one of the following Bluetooth Setting items.
PAIR ↔ SELECT ↔ PRIORITY ↔ DELETE ↔PREVIOUS ↔ PAIR ↔ ... - Press SET button to enter the Setting mode. “EQ”, “TONE” and “BT” appear.
Rotate TUNE dial to select the “BT” menu, then press ENTER button.
Rotate TUNE dial to select the desired Bluetooth Setting item, then press ENTER button. 1.
2.
3.Setting the Bluetooth mode ▶
Rotate TUNE dial to select device list or adjust value, then press ENTER button. 4.
PAIR: enter the pairing (Key Code: 00xx).
SELECT: selects one of 5 Bluetooth devices for connection.
PRIORITY: selects the priority of connection.
DELETE: deletes a Bluetooth device.
PREVIOUS: return to the BT menu. -
-
-
-
-
Incase of the delete selecting
Rotate TUNE dial to select the “YES” or “NO”, then press ENTER button.
YES: Deletes the selected Bluetooth device list.
NO: Cancels the Delete operation. 6. Incase of the pair selecting
Follow steps 2 to 4 in 17 page “Pairing your phone and car audio system” to complete the
pairing. 5.

02-93170-01
Ring - Snap
Ring - Snap
Bearing - Ball
Pinion assembly - Main drive
Bearing - Needle roller
Ring - Synchronizer
Ring - Snap
Sleeve - Synchronizer
Key assembly - Synchronizer
Hub - Synchronizer
Ring assembly - Triple cone
Gear assembly - 3rd speed
Bearing - Needle roller
Shaft - Main
Gear assembly - 2nd speed
Bearing - Needle roller
Ring assembly - Triple cone
Hub - Synchronizer
Sleeve - Synchronizer 1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.Ring assembly - Triple cone
Gear assembly - 1st speed
Sleeve - 1st gear
Bearing - Double angular ball
Ring - Snap
Gear - Main shaft 5th
Spacer
Gear - Main shaft 6th
Sleeve - Reverse gear
Bearing - Needle roller
Gear assembly - Reverse speed
Ring assembly - Triple cone
Hub - Synchronizer
Sleeve - Synchronizer
Stopper - Synchronizer key
Bearing - Ball
Flange assembly - Companion
O-ring
Nut - Locking (4WD: 245.1 ~ 264.7 Nm,
2WD: 117.6 ~ 137.2 Nm) 20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.

02-10
33163-00 Counter shaft ▶
Ring - Snap
Bearing - Roller
Gear - Counter shaft
Gear - Counter shaft cluster
Bearing - Roller
Sleeve - Speed gear
Bearing - Needle roller
Gear assembly - 5th speed
Key assembly - Synchronizer
Ring assembly - Triple cone 1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Hub - Synchronizer
Sleeve - Synchronizer
Ring - Synchronizer
Sleeve - Speed gear
Bearing - Needle roller
Gear assembly - 6th speed
Gear - Counter shaft
Nut - Locking (156.9 ~ 186.3 Nm)
Bearing - Needle roller 11.
12.
13.
14.
15.
16.
17.
18.
19.

11-74610-00
Problem Possible Cause Action
Excessive vibration of
steering wheel (shimming)Broken steering linkage Replace
Looseness of steering gear box Retighten
Broken or binding of steering ball joint Replace
Worn or damaged front wheel bearing Replace
Damaged wheel or tire Repair or replace
Defective suspension Repair or replace
Abnormal noise from
steering systemLooseness of steering gear box Retighten
Defective steering gear Replace the gear
assembly
Interference between steering column and
partsRepair
Looseness of steering linkage Retighten
Loosened or damaged oil pump drive belt Repair or replace
Looseness of oil pump bracket Retighten
Looseness of oil pump Retighten
Air insertion into system Bleed air
Defective oil pump Replace
Abnormal noise when
turning steering wheelLooseness of steering column Retighten
Worn or damaged steering shaft bearing Replace the steering
column
Looseness of intermediate shaft Retighten
Too heavy steering wheel Worn or damaged steering shaft bearing Replace the steering
column
Ignition key cannot be
inserted into key cylinderDefective lock cylinder Replace the steering
column
Defective ignition switch Replace the ignition
switch

03-297410-01
Driver & Front
Passenger
Seat Warmer Switches
3) To Activate Driver & Front Passenger Seat Warmer
Operating condition ▶
Turn the ignition key to the "ON" position and start the engine.
If the cranking signal is inputted, the seat warmer stops working during cranking.
Operation description ▶
When pressing the seat warmer switch for the driver and/or front passenger seat with IGN ON, the
seat warmer operates. Press the switch again to stop the seat warmer.
Operation procedures ▶
When pressing the seat warmer switch for the driver and/or front passenger seat, the seat warmer
relay in the ICM box is activated to supply power to the seat warmer.
ICM Box Driver & Front
Passenger
Seat Warmer Activated
The driver and front passenger seat warmers have separate circuits, allowing them to function
independently.