2013 SSANGYONG TURISMO lock

11-54610-00
3. TIGHTENING TORQUE
Description Kgf?m N?m
Steering column shaftSteering column mounting bolt 2.0 ~ 2.5 19.6 ~ 24.5
Steering wheel and steering column shaft
lock nut4.0 ~ 6.0 39.2 ~ 58.8
Steering wheel and air bag module
mounting bolt0.7 ~ 1.1 6.8 ~ 10.8
Steering column and lower shaft
connection bolt.1.8 ~ 2.5 17.6 ~ 24.5
Power steering gear
boxSteering gear box and gear box cross
member mounting bolt7.0 ~ 9.0 68.6 ~ 88.2
Steering gear box and lower shaft
connection bolt2.5 ~ 3.0 24.5 ~ 29.4
Tie rod end and knuckle connection nut 3.5 ~ 4.5 34.3 ~ 44.1
Tie rod end lock nut 6.5 ~ 8.0 63.7 ~ 78.4
Steering gear box and pressure hose
connection nut3.2 ~ 3.8 31.4 ~ 37.2
Steering gear box and return line
connection nut3.2 ~ 3.8 31.4 ~ 37.2
Power steering pumpEye bolt for oil supply pipe to power
steering pump5.5 ~ 6.5 53.9 ~ 63.7
Power steering pump mounting bolt 2.0 ~ 2.5 19.6 ~ 24.5
Power steering line Return line and clip connection bolt 1.2 ~ 1.8 11.7 ~ 17.6

11-74610-00
Problem Possible Cause Action
Excessive vibration of
steering wheel (shimming)Broken steering linkage Replace
Looseness of steering gear box Retighten
Broken or binding of steering ball joint Replace
Worn or damaged front wheel bearing Replace
Damaged wheel or tire Repair or replace
Defective suspension Repair or replace
Abnormal noise from
steering systemLooseness of steering gear box Retighten
Defective steering gear Replace the gear
assembly
Interference between steering column and
partsRepair
Looseness of steering linkage Retighten
Loosened or damaged oil pump drive belt Repair or replace
Looseness of oil pump bracket Retighten
Looseness of oil pump Retighten
Air insertion into system Bleed air
Defective oil pump Replace
Abnormal noise when
turning steering wheelLooseness of steering column Retighten
Worn or damaged steering shaft bearing Replace the steering
column
Looseness of intermediate shaft Retighten
Too heavy steering wheel Worn or damaged steering shaft bearing Replace the steering
column
Ignition key cannot be
inserted into key cylinderDefective lock cylinder Replace the steering
column
Defective ignition switch Replace the ignition
switch

01-36810-30
1. SPECIFICATION
Item FATC Manual
A/C controllerRated voltage DC 12 V DC 12 V
Operating voltage DC 9 to 16 V DC 9 to 16 V
Current consumption 2 A 2.5 A
Operating temperature-30~75℃ -30~80℃
Dark current 2 mA or less -
A/C compressorDiameter of pulley 120 mm
Rated voltage DC 12 V
Current consumption 2.2 A
Refrigerant fluid PAG RL 897 150cc
CondenserSize 655.8wX485.6hX16.0t
Receiver drierMoisture absorbent XH-9
Pressure switch Refrigerant pressure sensor
Front heater &
A/C moduleHeating capacity 7000 Kcal/hr
Cooling capacity 6200 Kcal/hr
Expansion valve Block type
Rear heater &
A/C moduleHeating capacity 4300 Kcal/hr
Cooling capacity 3200 Kcal/hr
Refrigeranttype R134a
Volume1050g ± 30g
PTC heaterMaterial barium titanate (BaTiO3)
Power consumption 1,000 W

01-156810-30
3. SYSTEM BLOCK DIAGRAM
A/C compressor OFF conditions ▶
Coolant temperature: over 115℃
Engine speed: over 4,500 rpm for more than 2 seconds
Engine speed: below 650 rpm
Maximum output due to abrupt acceleration
Excessive acceleration
Increased load during engine idling (to prevent the engine from shutting off)
Refrigerant pressure: over 32 bar or below 2 bar
Defects in A/C related system (refrigerant pressure sensor, coolant temperature sensor, cooling fan) 1.
2.
3.
4.
5.
6.
7.
8.

02-12
4. OPERATION PROCESS
1) Air Bag System Block Diagram
The overall air bag operation process and its functions and roles are broadly explained in this block
diagram. This diagram summarizes and highlights the functions adopted by Ssangyong Motors. -

03-197410-01
Power Seat
To adjust seat slide
Moving the slide switch forward and rearward
activates the slide motor to move the seat
forward and rearward.
To adjust seat back angle
When moving the upper part of the recline
switch forward/backward, the seatback angle is
adjusted as the recline motor rotates the rail.Manual Seat
To adjust seat slide
To move the seat forward or backward, pull and
hold the seat slide lever up and move the seat.
To adjust seat back angle
To fold the seatback, pull the seatback lock
release lever to release the lock. Then, lean
back to the desired angle and release the lever.
To adjust seatback ▶

03-20
Power Seat
To adjust seat cushion angle
When moving the front and rear parts of the
slide switch upwards or downwards, the front
and rear up/down motors rotate the rails to
move the front and rear side of the cushion
up/down.
To adjust seat height
When moving the slide switch up/down,
the front rear up/down motor rotates the rail to
move the whole seat cushion up/down.Manual Seat
To adjust seat cushion angle and
height
Turn the adjusting knob on the side of the seat
clockwise or anticlockwise to adjust the height
or angle of the front side or rear side of the
cushion.
To adjust driver seat lumbar support
When you raise and lower the adjusting lever
on the power and manual seats, the lumbar
support goes in and out of the seat.
The lumbar support is only fitted to the vehicle without the seat air bag.