2013 SSANGYONG NEW ACTYON SPORTS front light

02-44
2. STICS CONTROL REGARDING THEFT WARNING ALARM
1) Armed mode
The followings are definition of DOOR OPEN/CLOSE and DOOR LOCK/UNLOCK in\
respect of theft
deterrent system.
-
DOOR OPEN and DOOR CLOSE DOOR OPEN:
- Any of all door switches (including engine hood, driver's door, passenge\
r's door or
rear door) is in "OPEN" position.
DOOR CLOSE:
- All door switches (including engine hood, driver's door, passenger's doo\
r, rear
door and tailgate) are in "CLOSE" position.
The door lock/unlock operation does not affect the engine hood.
OPEN/CLOSE of the dech tailgate does not affect entering the armed mode.\
In other words, when the hood and front/rear door are closed even if the\
dech tailgate is open, the
vehicle can enter the armed mode.
-
-
DOOR LOCK & DOOR UNLOCK DOOR LOCK:
-
Indicates that driver's, passenger's and rear door and tailgate lock swi\
tches are in
LOCK positions.
DOOR UNLOCK:
- Indicates that driver's, passenger's or rear door or tailgate lock switc\
hes are in
UNLOCK positions.
Engine hood open warning lamp
The warning lamp comes on when the engine hood
is open.
Since the luggage room tailgate does not have the door switch, the door ajar warning light does not
come on when it is open.

04-58210-01
1. DESCRIPTIONS OF INDICATOR DISPLAY
Tachometer
SSPS warning light
Immobilizer indicator
Glow indicator
ESP indicator/warning light
Front fog light indicator
High beam indicator
ESP OFF indicator
Seat belt reminder (driver’s seat)
Seat belt reminder (passenger’s seat)
Engine oil pressure warning light
LCD Display
Engine overheat warning light
Engine check warning light
Auto cruise indicator
Light indicator
Winter mode indicator 1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.Engine hood open warning light
Battery charge warning light
Hazard Indicator
Water separator warning light
Air bag warning light
4WD CHECK warning light
4WD LOW indicator
4WD HIGH indicator
Speedometer
Turn signal indicator
Coolant temperature gauge
Brake warning light
Door ajar warning light
ABS warning light
Fuel gauge
Low fuel level warning light 18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33. It sends and receives information to/from each unit through CAN communication line. The LCD display
and separate ESP ON/OFF indicator are newly added.

04-8
Indicators on Instrument Cluster ▶
No. Symbol Item
1
Turn signal lamp-L
2
Turn signal lamp-R
3
4WD HIGH indicator
4Winter mode indicator
5Front fog lamp
indicator
6Cruise control
indicator
7Light illumination
indicator
8
High beam indicator
9
ABS warning lamp
10
Glow indicator
11
Immobilizer indicator
12Low fuel level warnig
lightPower Turning ON condition
Multifunction
switchWhen activating switch
Multifunction
switchWhen activating switch
IGN IGN ON/ CAN signal input
IGN IGN ON/ CAN signal input
Fog lamp
relayWhen activating switch
IGN IGN ON/ CAN signal input
BATT Tail lamp ON
Headlamp
high beam
relayWhen activating switch
IGNIGN ON/ CAN signal input
(ABS, EBD)
IGN IGN ON/ CAN signal input
IGN IGN ON/ CAN signal input
IGN When analog inputting fuel level

05-38310-00
1. SPECIFICATIONS
AmountSpecification
EU General
Exterior lamp Headlamp Low beam / High
beam2 H4(60W) /
H4(55W)←
Turn signal lamp 2 PY21W←
Position lamp 2 W5W←
Front fog light 2 H27W←
DRL 2 P21W←
Side repeater 2 LED←
Rear combination
lampStop (tail) lamp 2 P21W(5W)←
Turn signal lamp 2 PY21W←
Back-up lamp 1/2 P21W/1 P21W/2
Rear fog light 1 P21W -
License plate lamp 2 W5W←
Interior lamp Front room lamp 2 8W←
Glove box lamp 1 5W←
Center room lamp 2 10W←
Door courtesy lamp 2 5W←Description
The surface of lamps can get foggy when raining or washing the vehicle. This is normal and is a result
of the temperature difference between inner and outer surface of lamp cover. However, if water gets
into the lamp, have the system checked at Ssangyong Authorized Service Center.

06-98610-08
Major Functions of Multifunction Switch (Added functions)
Automatic hazard warning flasher switch
<00470047004700470d960047006900990090008c008d009300a0004700970099008c009a009a00610047006f008800a100880099008b0047009e00880099009500900095008e0047008d00930088009a008f008c0099004700890093009000950092009a00
47009b008f0099008c008c0047009b00900094008c009a0055>
<00470047004700470d96004700770099008c009a009a004700880095008b0047008f00960093008b00610047006f008800a100880099008b0047009e00880099009500900095008e0047008d00930088009a008f008c009900470089009300900095009200
9a0047009b008c00950047009b00900094008c009a0055>Auto washer switch
Washer fluid is sprayed on
the windshield and the
wiper sweeps off 4 times.
Then, the fluid will be
sprayed again and the
wiper will automatically
operate 3 times.
Auto light switch
Front wiper and washer coupled operation
Pull the lever briefly (below 0.6 seconds):
Wiping without washer spray
Pull and hold the lever for more than 0.6 seconds:
Three wiping cycles with washer spray
4WD control switch
Driver's heated
seat switch
Passenger's heated
seat switchAudio remote control switch
Gear shift switch
Front room lamp spot switch
Sun roof switch
Main room lamp switch
Front wiper operation range
(move the wiper lever up/down)
Head lamp leveling
switch

08-10
2. FRONT SUSPENSION (DOUBLE WISHBONE)
Advantage ▶
The advantage of a double wishbone suspension is that it is fairly easy to work out the effect of
moving each joint, so the kinematics of the suspension can be tuned easily and wheel motion can
be optimized.
It is also easy to work out the loads that different parts will be subjected to which allows more
optimized lightweight parts to be designed.
They also provide increasing negative camber gain all the way to full jounce travel unlike the
MacPherson strut which provides negative camber gain only at the beginning of jounce travel and
then reverses into positive camber gain at high jounce amounts. 1.
2.
3.
Disadvantage ▶
The disadvantage is that it is slightly more complex than other systems like a MacPherson strut. Due to
the increased number of components within the suspension setup it takes much longer to service and is
heavier than an equivalent MacPherson design. 1.
2. Double wishbone suspension is an independent suspension design using two (occasionally parallel)
wishbone-shaped arms to locate the wheel. Each wishbone or arm has two mounting points to the chassis
and one joint at the knuckle. The shock absorber and coil spring mount to the wishbones to control vertical
movement. Double wishbone designs allow the engineer to carefully control the motion of the wheel
throughout suspension travel, controlling such parameters as camber angle, caster angle, toe pattern, roll
center height, scrub radius, scuff and more.
Lower arm Upper arm Shock absorber Stabilizer

02-38810-01
1. CAUTIONS FOR AIR BAG OPERATION
When there is any deployed air bag (including seat belt pretensioner), the air bag unit should be
replaced. Any DTC (Diagnostic Trouble Code) in the air bag unit should not be cleared since the
unit has data for status when the air bag was deployed as well as information related to the air bag
deployment.
Note that the used components related to the air bag, especially the air bag unit, should be
packaged in an air tight container to prevent any damage.
Do not connect a tester to any connector or component to check supply voltage or resistance of ai
r
bag related components. The detonator may explode due to a sudden extra power supplied by the
tester.
Before removing or installing any air bag related components, disconnect the negative battery
cable. 1.
2.
3.
4.
Collision sensors, a kind of impact G (acceleration) sensor, detect the lateral and longitudinal collisions
and determine whether or not to deploy air bags. The roles of each collision sensor are as follows:
Front G sensors (inside the air bag unit)
Send signals to the front air bags (driver and passenger air bags) and the driver's and front
passenger's seat belt pretensioners. When the front collision G sensor sends out only the air bag
deployment signal, the signal deploys the two front air bags and activates their seat belt
pretensioners.
Once an air bag deploys, its repair parts vary according to the deployment situation and damage to the
vehicle from collision. Needed repairs also slightly vary between the front air bags and the curtain air
bags. The following are the differences:
Replacement parts when the front air bags deploy:
Air bag unit and its wiring (including connector), seat belt pretensioner and its wiring (including
connector), whole front air bags, instrument panel (IP)

02-8
1. OVERVIEW
Collision sensors, a kind of impact G (acceleration) sensor, detect the lateral and longitudinal collisions
and determine whether or not to deploy air bags. The roles of each collision sensor are as follows:
Front G sensors (inside the air bag unit))
Send signals to the front air bags (driver and passenger air bags) and the driver's and front
passenger's seat belt pretensioners. When the front collision G sensor sends out only the air bag
deployment signal, the signal deploys the two front air bags and activates their seat belt
pretensioners.
Once an air bag deploys, its repair parts vary according to the deployment situation and damage to the
vehicle from collision. Needed repairs also slightly vary between the front air bags and the curtain air
bags. The following are the differences:
Replacement parts when the front air bags deploy:
Air bag unit and its wiring (including connector), seat belt pretensioner and its wiring (including
connector), whole front air bags, instrument panel (for vehicle with passenger air bag) For the air bag system in KORANDO SPORTS, the seat belt pretensioners on both sides as well as the
driver/passenter air bags are deplyed when the front air bag is deployed like as they did.