2013 SSANGYONG NEW ACTYON SPORTS mirror

01-91113-01
4. DIAGNOSTIC INFORMATION AND PROCEDURE
1) Oil Leak Diagnosis
Most fluid oil leaks are easily located and repaired by visually finding the leak and replacing or repairing
the necessary parts. On some occasions a fluid leak may be difficult to locate or repair. The following
procedures may help you in locating and repairing most leaks.
Finding the Leak ▶
Identify the fluid. Determine whether it is engine oil, automatic transmission fluid, power steering
fluid, etc.
Identify where the fluid is leaking from. -
-
After running the vehicle at normal operating temperature, park the vehicle over a large sheet
of paper.
Wait a few minutes.
You should be able to find the approximate location of the leak by the drippings on the paper. ·
·
·
Visually check around the suspected component.
Check around all the gasket mating surfaces for leaks. A mirror is useful for finding leaks in
areas that are hard to reach.
If the leak still cannot be found, it may be necessary to clean the suspected area with a
degreaser, steam or spray solvent. -
-
Clean the area well.
Dry the area.
Operate the vehicle for several miles at normal operating temperature and varying speeds.
After operating the vehicle, visually check the suspected component.
If you still cannot locate the leak, try using the powder or black light and dye method. ·
·
·
·
·
Clean the suspected area.
Apply an aerosol-type powder (such as foot powder) to the suspected area.
Operate the vehicle under normal operating conditoins.
Visually inspect the suspected component. You should be able to trace the leak path over the
white powder surface to the source. -
-
-
- Powder Method ▶

02-38710-01
1. PERFORMANCE AND SPECIFICATIONS
1) Rated Load & Input Signals
Rated Load
▶
NO.
Item Rated Load
1 Chime bell / Buzzer DC 12V 350 mA (Inductive load)
2 Front room lamp DC 12V 16W (Lamp load)
3 Rear room lamp DC 12V 8W (Lamp load)
4 Ignition key illumination DC 12V 1.2W (Lamp load)
5 Seat belt indicator DC 12V 1.2W (Lamp load)
6 Parking brake warning lamp DC 12V 1.2W (Lamp load)
7 Door ajar warning lamp DC 12V 1.2W (Lamp load)
8 Door lock relay DC 12V 200 mA (Inductive load)
9 Door unlock relay DC 12V 200 mA (Inductive load)
10 Horn relay DC 12V 260 mA
11 Tail lamp relay DC 12V 200 mA (Inductive load)
12 Hazard warning lamp relay DC 12V 200 mA (Inductive load)
13 Power window relay DC 12V 200 mA (Inductive load)
14 Rear defogger relay DC 12V 200 mA (Inductive load)
15 Wiper LOW relay DC 12V 200 mA (Inductive load)
16 Wiper HIGH relay DC 12V 200 mA (Inductive load)
17 Front washer motor DC 12V 1.5A
18 Head lamp relay DC 12V 750 mA (Inductive load)
19 Front defogger relay DC 12V 200 mA (Inductive load)
20 Mirror lock relay DC 12V 200 mA (Inductive load)
21 Mirror unlock relay DC 12V 200 mA (Inductive load)

02-4
Input Signals
▶
NO.
Input Signal Name Logic Status
1 IGN1 ON = BAT
(IGN ON or START)
2 IGN2 ON = BAT (IGN ON)
3 ALT_D ON = BAT (engine started)
4 Key reminder switch IN = BAT (key in)
5 Driver's door switch OPEN = GND, CLOSE = OPEN
6 Passenger's door switch OPEN = GND, CLOSE = OPEN
7 Rear door switch - OPEN (one of rear doors) = GND
- CLOSE (all rear doors) = OPEN
8 Hood switch OPEN = GND, CLOSE = OPEN
9 Driver's door lock/unlock switch LOCK = OPEN, UNLOCK = GND
10 Passenger's door lock/unlock switch LOCK = OPEN, UNLOCK = GND
11 Rear door lock/unlock switch - UNLOCK (one of rear doors)
= GND
- LOCK (all rear doors) = OPEN
12 Tailgate lock/unlock switch LOCK = OPEN, UNLOCK = GND
13 Rear defogger switch ON = GND, OFF = OPEN
14 Seat belt switch Unfastened = GND, Fastened = OPEN
15 Sunroof open switch ON = GND, OFF = OPEN
16 Parking brake switch ON = GND, OFF = OPEN
17 Air bag collision sensor ON = 200 ms output (LOW), OFF = OPEN
18 Wiper motor (parking) switch STOP = BAT VOLTAGE, ROTATING = GND
19 Washer switch ON = BAT, OFF = OPEN
20 INT-AUTO switch ON = BAT, OFF = OPEN
21 Auto washer switch ON = BAT, OFF = OPEN
22 Intermittent resistance 0W ~ 51KW (for intermittent wiper)
23 Speed sensor ON = GND (PWM), OFF = OPEN
24 Mirror lock/unlock switch ON = GND, OFF = OPEN
25 Front defogger switch ON = GND, OFF = OPEN
26 Auto hazard switch ON = GND, OFF = OPEN

02-358710-01
The defogger system uses the heated glass to remove the moisture and fro\
st on the windows, which
can disturb safe driving.
The defogger (including de-icer) activates the corresponding switch an\
d the STICS controls the
operating time.Tailgate and outside rearview mirror
heated glass switch
Pressing switch activates tailgate and outside
rearview mirror heated glass for approx. 12
minutes
Windshield heated glass (de-icer) switch
Pressing switch activates windshield heated
glass for approx. 12 minutes

02-54
Outside rearview mirror folding/unfolding control
▶
If you press the folding/unfoling switch with the ignition switch in "ON\
" position, the outside rearview
mirror is folded or unfolded depending on the previous status. At this t\
ime, folding/unfolding outputs
are maintained for about 15 to 17 seconds.
Even though the ignition switch is turned to "OFF" position during foldi\
ng/unfolding output, the output
continues on for remaining time.
When removing and refitting the battery, the first switch input folds th\
e mirror.
If you turn the ignition switch to the "OFF" from "ON" position, operating time is extended by 60
seconds. Unlikely the previous model, opening the front door does not af\
fect the extension time.
(i.e., opening/closing the front door is irrelevant)
If the unfolding input is received from the switch during folding output\
or the folding input is received
during unfolding output, the existing output stops and new output is act\
ivated after the delay time of
about 0.1 second.
When the vehilce speed is above 50 km/h with the mirror unfolded, even t\
hough the folding signal is
received it is overridden.
(folding is possible only at vehicle speed of less than 50 km/h )
1.
2.
3.
4.
5.
6.

02-558710-01
STICS Outside Rearview Mirror Folding/Unfolding Control Circuit
▶
If you remove the ignition switch and open the driver's door with the su\
nroof open, the chime buzzer
sounds.
As soon as you close the driver's door or the sunrooof, the chime buzzer\
output stops.
However, when operating conditions in step (1) are met after the opera\
tion in step (2), the chime
buzzer will not sound again. If you turn the ignition swtich to the "ON"\
position again and the
operating contions in step (1) are met, the chime buzzer sounds again.\
If the operating condtions for door ajar warning and sunroof open warnin\
g are met at the same time,
the sunroof open warning is activated preferentially.
1.
2.
3.
4.
In order to prevent the driver from getting off the
vehicle with the sunroof open, the reminder function for
the driver is added. This function is activated as follows: Sunroof open warning
▶

06-4
Outside rearview mirror control bezel switch ▶
Item Rated load
Outside rearview mirror switch 12 V-2 A
ESP OFF switch 12 V-0.1 A
Mirror folding switch 12 V-0.1 A
Steering wheel heating switch 12 V-0.1 A
Rear Fog Lamp Switch 12 V-0.1 A
CTR fascia switch bezel ▶
Item Rated load
4WD control switch 12 V-0.1 A (signal load)
Driver's heated seat switch 12 V-5 A (relay load)
Passenger's heated seat switch 12 V-5 A (relay load)
Head Lamp Leveling Switch 12 V-1 A (inductive load)
Rear heated seat switch ▶
Item Rated load
Rear heated seat switch 12 V-0.1 A

06-58610-08
8510-60 Heated steering wheel switch
- Heated steering wheel switch added to outside mirror switch bezel
8510-10 Rear seat warmer switch
- Adopt rear seat warmer switches to rear door LH/RH
2. MAJOR CHANGES