2013 SSANGYONG KORANDO door lock

Door LOCK/UNLOCK by REKES key
When the REKES LOCK switch is pressed less than 0.5 seconds (T1), the door LOCK relay is
activated for 0.5 seconds (T2).
All of following conditions are met within 0.2 seconds (T4) after the chattering time (T3): A.
B. Operation 1.
When the REKES UNLOCK switch is pressed less than 2 seconds (T5), the door UNLOCK relay is
activated for 0.5 seconds (T2).
The door UNLOCK conditions are met, the turn signal lamp is operated once for 1 second. D.
E. Operation 2.
All doors closed
Hood closed
Tailgate closed
Door LOCK detection switch in LOCK state -
-
-
-
The turn signal lamp flashes 2 times at intervals of 0.5 sec. ON/0.5 sec. OFF. C.
Operating process (for vehicles without SKM)
Do not operate the REKES key with the ignition key inserted or for 1 second after the ignition key is
removed. (to prevent the remote controller switch malfunction)
When one of the LOCK switches is unlocked after the door LOCK, all doors will be unlocked. -
-

8710-01
The door LOCK/UNLOCK relay is installed inside the actuator.

Door LOCK/UNLOCK control by smart key
The SKM receives LOCK signal through B-CAN with IGN OFF or ACC ON.
The BCM outputs LOCK relay signal for 0.5 seconds (T2).
The turn signal lamp is turned ON for 0.5 seconds and then turned OFF for 0.5 seconds, and this
operation is repeated 2 times. A.
B.
C. Operation 1.
SKM receives UNLOCK signal through B-CAN with IGN ON, IGN OFF, or ACC ON.
BCM outputs UNLOCK relay signal for 0.5 seconds (T3).
The turn signal lamp is operated once for 1 second. D.
E.
F. Operation 2.
The door LOCK/UNLOCK relay is installed inside the actuator.

Door LOCK/UNLOCK control by door handle switch
The ignition is turned ON or OFF, or the ACC is turned ON.
When the door handle switch is operated, the door LOCK/UNLOCK signal is sent to the BCM through
B-CAN.
The SKM operates the turn signal lamp once for 1 second after 0.5 seconds (T3) of door UNLOCK
relay operation. A.
B.
C. Operation 1. (when driver door locked)
The ignition is turned OFF or ACC is turned ON.
When the door handle switch is operated, the door LOCK/UNLOCK signal is sent to the BCM through
B-CAN.
The SKM operates the turn signal lamp twice at intervals of 0.5 sec. ON/0.5 sec. OFF after 0.5
seconds (T2) of door LOCK relay operation. D.
E.
F. Operation 2. (when driver's door unlocked)
Operating process (for vehicles with SKM)
When the driver door is unlocked after passive UNLOCK signal is received with IGN ON, the door is
not locked.

8710-01
The door LOCK/UNLOCK relay is installed inside the actuator.

AUTO door LOCK control
REKES LOCK
The vehicle is driven at 30 km/h or more.
The door LOCK relay is activated for 0.5 seconds (T2).
The door LOCK relay is not activated when all doors (except tailgate) are locked or door malfunction
signal is input. A.
B.
C. Operation 1.
The UNLOCK signal by other switch is received.
The door LOCK signal is output 5 times for the switch. F.
G. Operation 3. (during operation 2)
A door is unlocked.
The door LOCK signal is output 5 times (T3) except the door LOCK carried out in operation 1. D.
E. Operation 2. (after operation 1)
The door LOCK system outputs UNLOCK signal automatically when the LOCK output conditions
are met by this function or the ignition is turned ON to OFF. (even when there is no LOCK output
while the vehicle is driven at over 30 km/h under LOCK condition). - If a door is unlocked after the 5 times of LOCK output, the door is regarded as malfunctioning.
If there is a malfunctioning door, the AUTO door LOCK is not activated but the LOCK operation by
the central door LOCK switch is available.
If a malfunction occurs when the vehicle is driven at 30 km/h or more, the AUTO door LOCK will not
be activated even when the vehicle speed decreases to 30 km/h or less and then increases to 30
km/h or more.
The faulty door will be reset when the unlocked malfunctioning door is locked. -
-
-
-
The faulty door will be reset when the ignition is turned OFF.
When one of the door LOCK switches is in LOCK position with the ignition turned OFF, all doors
are unlocked. -
-

8710-01
Operating process (for vehicles without SKM)
The door LOCK/UNLOCK relay is installed inside the actuator.

AUTO UNLOCK upon receiving air bag deployment signal
Air bag deployment signal is not input for initial 7 seconds (T4) after IGN ON A. Operation 1.
Signal from unlock relay is output for 5 seconds (T3) after 40 ms (T2)
When turning IGN OFF during 5 seconds (T3) of unlock relay signal output
Signal from unlock relay is input for the rest of the time B.
C.
D.
E. Operation 2.
The room lamp comes on when the air bag deployment signal is input except when the room lamp
switch is turned off.
The hazard warning lamp flashes when the air bag deployment signal is input.
Resetting the auto door unlock function turns off the battery (cutting off BCM power). -
-
-
The door LOCK/UNLOCK relay is installed inside the actuator.