2013 SSANGYONG KORANDO ignition

Indicator
(green)
Passenger seat belt reminder
Left turn signal indicator
Right turn signal indicator
Indicator
(red)
Indicator
(green)
Indicator
(green)
Winter mode indicator(DSL only)
The right turn signal indicator blinks if the light switch is pushed up to
the right, and both turn signal indicators blink if the hazard warning flasher
switch is pressed.
When the mode switch is pressed, the winter mode is selected and the
winter mode indicator comes on on the instrument cluster. The winter
mode is used to start off on a slippery road with the 2nd gear. If the switch
is pressed again, the winter mode is deactivated and system returns to
standard mode.This indicator comes on when the ignition switch is turned to the "ON"
position and goes off when the passenger's seat belt is fastened.
The left turn signal indicator blinks if the light switch is pushed down to the
left, and both turn signal indicators blink if the hazard warning flasher switch
is pressed.
Smart key warning lamp
Indicator
(amber)
This lamp comes on when the uncertified transponder or smart key is
detected,
SKM system is defective or there is no smart key in the vehicle.

8010-01
Indicator
(amber)
Steering wheel heating indicator
This indicator comes on when the steering wheel heating switch
is operated with the ignition switch turned on and the engine running.
(applies to SVC class)
TPMS WARNING LIGHT
Indicator
(amber)
GLOBAL WARNING LIGHT
Indicator
(amber)
GSI (GEAR SHIFT INDICATOR)
This warning light comes on when the ignition switch is turned to
this warning light comes on.
This warning light comes on when the ignition switch is turned to
If the tire pressure is too low, this warning light blinks for 70 seconds and
then ON.
This indicator indicates the proper gear shifting time.
Shift-up to 3rd gear (currently 2nd gear or lower)
Shift-down to 3rd gear (currently 4th gear or higher)
If the system is properly working, this indicator is invisible.Ex)

8010-01
Operations for power supply in SVC
When the ignition switch is turned to ON position, the message "WELCOME" is displayed for 2
seconds on the DOT LCD and the seat belt reminder comes on for 4 seconds. However, if a signal
with higher priority is received, the seat belt reminder comes on only for 2 seconds
to display it.
The pre-warning (system check) indicator comes on for 4 seconds and goes off 0.4 seconds after
that the ignition is switched on.
All input signals can be input 4 seconds after the pre-warning (system check) indicator starts
illuminating.
Only the symbol and DOT LCD are illuminated initially, if the SKM (Smart Key Module) or door (B-
CAN) signal is received
while B+ power is supplied.
If the ignition is switched on with the LCD illuminated, the DOT LCD and the symbol follow
the side fascia panel.
When the step 1, 2 and 3 are performed after 4 seconds, the seat belt warning lamp is deactivated
in advance.
Dial light ON condition: Lights up gradually for 2 seconds when the ignition is switched on. 1.
2.
3.
4.
5.
6.
4) Illumination & Brightness
(1) Operations for Power Supply

When the ignition is switched off, the message "GOOD-BYE" is displayed for 2 seconds and disappears.
The other LCDs go off as soon as the ignition is switched off.
The dial and pointer dim down for 2 seconds and go off at the same time when the DOT LCD goes off. 7.

8010-01
Operations for power supply in STD
The operation input before the LCD backlight is illuminated, right after the ignition is turned OFF or ON,
is ignored.
detected.
The LCD display, LCD backlight, dial lamp and indicator lamp are turned on or off by the ignition
switch ON/OFF operation. -
-
-

8010-01
The pre-warning of the MICOM control warning is performed 400 ms after turning the ignition switch to
ON position.
IGN ON detecting time: 40~80 ms after turning ignition switch to ON position -
- The pre-warning is performed for 4 seconds after turning the ignition switch to ON position. BCM checks
that the warning lamps (ABS, ESP, ESP OFF, 4WD CHECK, 4WD LOCK) are matched with CAN
signals.
The pre-warning is performed by the variant code.

8010-01
The pre-warning of the MICOM control warning is performed 400 ms after turning the ignition switch
to ON position.
IGN ON detecting time: 40~80 ms after turning ignition switch to ON position -
- The pre-warning is performed for 4 seconds after turning the ignition switch to ON position. BCM checks
that the warning lamps (ABS, ESP, ESP OFF, 4WD CHECK, 4WD LOCK) are matched with CAN
signals.
The pre-warning is performed by the variant code.

When the ignition is switched on and the vehicle is drived more than 10 km, average fuel consumption
is displayed at every 200 ms, based on the fuel consumption and driving distance for 600 ms. -
Function Signal Remark
Display type DOT BAR TYPE(92DOT)
Display range
Resolution
(DOT)
0.5435(MPG per Bar)
Display interval

(3) Instant Fuel Consumption Mode
The LCD display indicates the instant fuel consumption (for 2 seconds) calculated based on driving
distance and fuel consumption for last 2 seconds.
Function Signal Remark
Display type 3 digits LCD
Display range 0.0 ~ 99.9
Resolution 0.1 km (mile)
Display interval every 2 seconds