2013 Seat Toledo heating

112Seats and storage
Heated front seats*
Fig. 71 Heated front
seats
The cushion and backrest of the front seats can be heated electri-
cally.
Press the 
or  ⇒ 
Fig. 71 button to switch on and adjust the
heated front seats.
Press once to connect the heating at maximum force.
Press the button again to reduce the force of the heating and
switch it off. The force is indicated by the number of warning lamps
lit on the button.
WARNING
Do not use the heated seat if your perception of pain and/or temperature
or that of your passenger is limited, e.g. due to medication, paralysis or
chronic illness (e.g. diabetes). It could cause burns on the back, buttocks
and legs that are difficult to heal. If you still want to use the heated seat,
take frequent breaks on long journeys so that the body can recover from
the trip. Ask you doctor about your particular situation.
CAUTION
● To avoid damaging the heating elements, do not kneel on the seat or
apply sharp pressure at a single point to the seat cushion or backrest.
● Do not use the heated seats if nobody is sitting on them or if there are
items attached to or lying on them, such as a child seat or a bag, etc. This
could lead to a fault in the seat heating elements.
● Do not clean the seats with liquid ⇒ page 177.
Note
● Only connect the heated seats when the engine is running. This pro-
vides considerable savings on the battery capacity.
● In the event of a drop in voltage in the onboard systems, the heated
seats switch off automatically to ensure enough power to control the engine
⇒ page 194, Automatic disconnection of electrical equipment. 
Head restraints
Fig. 72 Head restraints: adjusting/removing head restraints 

116Seats and storage
CAUTION
Make sure sharp objects stored in the luggage compartment cannot not
damage the rear window heating filaments.
Note
Tyre pressure must be adapted to suit the load ⇒ page 197, Tyre useful life. 
Luggage compartment light
The light switches on automatically when the rear lid is opened. The light
switches off automatically 10 seconds after the rear lid has been opened. 
Category N1 vehicles
Category N1 vehicles with no protection grille must use a retaining set com-
pliant with Standard EN 12195 (1 – 4) to secure the load. Retaining elements*
Fig. 75 Luggage com-
partment: Retaining ele-
ments
The following retaining elements are fitted in the luggage compartment
⇒ Fig. 75.
Rings to secure the load and the retaining nets.
Rings used solely for the retaining nets.
CAUTION
The rings support a maximum load of 3.5 kN (350 kg).
Note
The front ring B is below the folding backrest of the rear seats
⇒ Fig. 75.
A
B

128Heating and air conditioning
Heating and air conditioning
Heating and air conditioning General notes
The power of the heating depends on the temperature of the coolant. There-
fore, maximum power is only obtained when the engine has reached operat-
ing temperature.
The temperature and the humidity of the air is reduced when the system
cools the interior of the vehicle. This therefore increases the comfort of all
vehicle occupants when outside temperatures and humidity are high. It also
helps prevent the windows from misting over during cold periods of the
year.
The air recirculation system can be switched on temporarily to increase the
cooling effect.
Keep the air intake slots in front of the windscreen clear of ice, snow or
leaves to ensure unimpaired heating and cooling.
When the air conditioning is on, condensation can drip from the evaporator
in the air cooling system and form a pool underneath the vehicle. This is
normal and does not indicate a leak!
WARNING
● All windows must be clear of ice, snow and condensation for driving
safety. Therefore, make sure you familiarise yourself with the correct use
of heating and ventilation, window demisting and defrosting and cooling.
● Never use the air recirculation system for too long, as it prevents
fresh air from entering the vehicle and “used” air can cause tiredness, re-
duce your attention span and cause the windows to mist over. This in-
creases the risk of an accident. Switch off the air recirculation system as
soon as the windows begin to mist over.
Note
● Used air escapes through ventilation slots in the rear of the luggage
compartment.
● Smoking is not recommended while the air recirculation system is in
use, as the smoke drawn from the interior of the vehicle settles in the evap-
orator of the air conditioning system. This causes a persistent, unpleasant
smell while the system is running that is time-consuming and expensive
(evaporator replacement) to eliminate.
● Never cover the air outlets to ensure the system operates correctly. 
Economic use of the air conditioning system
When the air conditioning is switched on, the compressor consumes engine
power and has influence on fuel consumption.
If the vehicle interior has overheated due to an excessive solar radiation, it
is best to open the windows or doors to allow the hot air to escape. 

129
Heating and air conditioning
While in motion, the air conditioning should not be switched on if the win-
dows are open.
If the interior temperature can be reached without switching on the air con-
ditioning, the fresh air mode should be used.
For the sake of the environment
This saves on fuel and reduces emissions. 
Faults
If the air conditioning does not work at outside temperatures above +5 °C
(+41 °F) then the system is faulty. This may be due to one of the following
reasons:
● One of the fuses has blown. Check the fuse and replace if necessary
⇒  page 219.
● The air conditioning compressor has switched off temporarily because
of an increased engine coolant temperature ⇒ page 58.
If you cannot repair the fault yourself or where the cooling power continues
to drop, switch the system off. Contact a specialised service. Air ventsFig. 96 Air vents
Opening air vents 3 and 4
– Turn the vertical circular control upwards.
Closing air vents 3 and 4
– Turn the vertical circular control downwards.
Changing the direction of air delivery from air vents 3 and 4
– The air circulation height can be varied by changing the posi-
tion of the sliding adjuster upwards or downwards ⇒ Fig. 96.
– The air circulation direction can be varied by changing the posi-
tion of the sliding adjuster to the right or to the left.
The flow of air from the vents is controlled using control C
⇒ Fig. 97. Vents
3 ⇒ Fig. 96 and 4 can be opened and closed individually.
Depending on the position of the adjusters and on the weather, open vents
can provide air which is either heated, unheated or cooled. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

130Heating and air conditioning
Heating
Operation
Fig. 97 Heating: controls
Temperature selection
– Turn rotary control A
⇒ Fig. 97 clockwise to increase the tem-
perature.
– Turn rotary control A
anti-clockwise to reduce the temperature.
Blower selection
– Turn rotary control B
⇒ Fig. 97 to position 1 to 4 to switch the
blower on.
– Turn rotary control B
to position 0 to switch the blower off.
– Press button 1
⇒  in Air recirculation on page 132 to close
the fresh air vent. Air distribution selection
–
Turn rotary control C
⇒ Fig. 97 to select the air vents
⇒ page 129, Air vents you wish to activate.
All controls, except control B
⇒ Fig. 97, can be set to any intermediate po-
sition.
Leave the blower activated at all times to prevent the windows from misting
over.
Note
If the system is set so that all of the air is used to defrost the windows, no
air is supplied to the footwell area. This could limit heating comfort. 

131
Heating and air conditioning
Heating selection
Recommended settings for the different modes:
SettingsControl positionbutton 1Air vents 4ABC
Windscreen and side window de-
frostClockwise as far as it
will go3Do not switch onOpen and direct towards the side window
Windscreen and side window de-
frostRequired tempera-ture2 or 3  Do not switch onOpen and direct towards the side window
Heat as quickly as possibleClockwise as far as itwill go3Switch on brieflyOpening
Mild heatingRequired tempera- ture2 or 3  Do not switch onOpening
Fresh air mode - blowerAnti-clockwise as faras it will goRequired positionDo not switch onOpening
Note
● Controls A ⇒ Fig. 97 ⇒ page 130, B, C and button 1.
● Air vents 4 ⇒ page 129.
● We recommend you leave the air vents 3 ⇒ page 129 in the open posi-
tion. 
Air recirculation
Air recirculation prevents unpleasant smells, e.g. when passing
through a tunnel or in queuing traffic, from entering the interior. Switching on air recirculation mode
–
Press button 

1 ⇒ Fig. 97 ⇒ page 130 and the lamp in the
button will light up.
Switching off air recirculation mode
– Press button 

1 ⇒ Fig. 97 ⇒ page 130 again and the lamp
in the button will switch off.
If air vent C
⇒ Fig. 97 ⇒ 
page 130 is in position
, air recirculation
mode switches off automatically. Press the  button to switch air recircula-
tion mode back on in this position. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

132Heating and air conditioning
WARNING
Never use the air recirculation system for too long, as it prevents fresh air
from entering the vehicle and “used” air can cause tiredness, reduce your
attention span and cause the windows to mist over. This increases the
risk of an accident. Switch off the air recirculation system as soon as the
windows begin to mist over.

Air conditioning (manual)* General notes
The air cooling system only works if the AC button
2 ⇒ Fig. 98
⇒ page 132 is pressed and under following conditions:
● The engine is running
● the outside temperature is above +2 °C (+36 °F)
● The blower control is in position 1 – 4
When the cooling system is on and under certain conditions, air can be
blown from the vents at a temperature of approx. +5 °C (+41 °F). In the
event of prolonged, irregular distribution of the air flow from the outlets and
significant differences in temperature, e.g. on leaving the vehicle, sensitive
people may catch a cold.
Note
A visit to the specialised service once a year is recommended to clean the
air conditioning system. Operation
Fig. 98 Air conditioning: controls
Temperature selection
– Turn rotary control A
⇒ Fig. 98 clockwise to increase the tem-
perature.
– Turn rotary control A
anti-clockwise to reduce the temperature.
Blower selection
– Turn rotary control B
⇒ Fig. 98 to position 1 to 4 to switch the
blower on.
– Turn rotary control B
to position 0 to switch the blower off.
– Press button 

1 ⇒ page 134, Air recirculation to close the
fresh air vent.
Air distribution selection
– Turn rotary control C
⇒ Fig. 98 to select the air vents
⇒ page 129 you wish to activate. 

133
Heating and air conditioning
Switching cooling on and off
– Press button A/C

2 ⇒ Fig. 98 and the lamp in the button will
light up.
– Press the A/C

2 button again and the LED in the button will
switch off.
Note
● If the air distribution is directed towards the windows, all, of the heating
power is used to defrost the windscreen. No warm air is directed to the foot-
well area. This could limit heating comfort.
● The A/C
button lamp lights up after the system has been switched on,
even if not all of the conditions for cooling system operations are met. Cool-
ing is indicated as available once all of the conditions are met ⇒ page 132,
General notes. 
Safety FirstOperating instructionsPractical TipsTechnical specifications