2013 Seat Leon SC spare wheel

Driving and the environment . . . . . . . . . . . . . . . 230
Running in the engine . . . . . . . . . . . . . . . . . . . . . 230
Driving through flooded roads . . . . . . . . . . . . . . . 230
Installation of exhaust gas filtration systems . . . 230
Economic and ecological driving . . . . . . . . . . . . . 231
Environmental friendliness . . . . . . . . . . . . . . . . . 232
Trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
Trailer towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
Retrofitting a towing bracket* . . . . . . . . . . . . . . . 236
Care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . 238
General information . . . . . . . . . . . . . . . . . . . . . . . 238
Care of vehicle exterior . . . . . . . . . . . . . . . . . . . . . 238
Care of the vehicle interior . . . . . . . . . . . . . . . . . . 242
Checking and refilling levels . . . . . . . . . . . . . . . 246
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
Filling the tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
Cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
Windscreen washer reservoir and wiper blades . 262
Wheels and tyres . . . . . . . . . . . . . . . . . . . . . . . . . . 265
Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
Accessories and modifications to the vehicle 272
Accessories, replacement parts and repairs . . . . 272
Technical modifications . . . . . . . . . . . . . . . . . . . . 272
Radio transmitters and business equipment . . . 272
Emergencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
General information . . . . . . . . . . . . . . . . . . . . . . . 274
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
Tyre repair kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
Changing a wheel . . . . . . . . . . . . . . . . . . . . . . . . . 277
Spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282 Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
Towing and tow-starting the vehicle . . . . . . . . . . 286
Fuses and bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291
Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Changing bulbs in headlight unit . . . . . . . . . . . . 295
Changing bulb for front fog light . . . . . . . . . . . . . 297
Changing tail light bulbs (on side panel) . . . . . . 299
Changing tail light bulbs (on rear lid) . . . . . . . . . 301
Changing number plate light bulbs. . . . . . . . . . . 303
Technical specifications . . . . . . . . . . . . 304
Technical specifications . . . . . . . . . . . . . . . . . . . . 304
Important . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304
Vehicle identification data . . . . . . . . . . . . . . . . . . 305
Information on fuel consumption . . . . . . . . . . . . 306
Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
Engine specifications . . . . . . . . . . . . . . . . . . . . . . 309
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
Filling capacities . . . . . . . . . . . . . . . . . . . . . . . . . . 323
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
4Table of Contents

148Seats and storage
● Remove the hooks and the straps of the net bag from the fastening rings
and the hooks for hanging bags.
● Store the net bag in the luggage compartment.
WARNING
Draw out the elastic net bag to secure it to the fastening rings. Once fas-
tened it remains taut. If the elastic net bag is hooked up and unhooked
wrongly, its hooks may cause injuries.
● Always ensure that the hooks do not suddenly release from the fas-
tening rings when hooking or unhooking them.
● When hooking or unhooking the hooks, protect your eyes and face to
prevent injury in case the hooks were suddenly released.
● Always hook up the net bag hooks in the described order. If a hook is
unexpectedly released, the risk of injury increases.

Applies to the model: LEON ST
Luggage compartment variable floor
Fig. 110 Luggage com-
partment variable floor:
positions
Fig. 111 Luggage com-
partment variable floor:
tilted slots
Variable floor in the high position
● Lift up the floor using handle
⇒ Fig. 110 A
and pull backwards on it un-
til the front of the floor has passed the supports B.
● Push the floor forwards over them until it engages with the rear seats
and then lower the floor with handle A
.
Variable floor in the low position
● Lift up the floor using handle
⇒ Fig. 110 A
and pull backwards on it un-
til the front of the floor has fully passed supports B.
● Match the front part with the slots in the bottom of the supports and
slide the floor forwards until it engages with the rear seat backrests and
then lower the floor with handle A
.
Variable floor in the tilted position
With the variable floor in the tilted position you can access the spare
wheel /anti-puncture kit area.
● Lift up the variable floor using handle
⇒ Fig. 110 A
and pull backwards
on it until the front of the floor has passed the tilted slots ⇒ Fig. 111 C.
● Slide the floor through the slots with the help of handle A until it en-
gages with the rear seat backrests and the floor is resting in the slots. 

217
Driver assistance systems
Wheel tread change
The wheel tread changes when:
● Tyre pressure is manually changed
● Tyre pressure is insufficient
● Tyre structure is damaged
● The vehicle is unbalanced because of a load
● The wheels on an axle are subject to a heavier load (e.g. when towing a
heavy load)
● The vehicle is fitted with snow chains
● The temporary spare wheel is fitted
● The wheel on one axle is changed
There may be a delay in the reaction of the tyre monitoring indicator  or it
may not indicate anything under certain circumstances (e.g. sporty driving,
snow-covered or unpaved roads, or when driving with snow chains). 
Calibrating the tyre monitoring indicator
Fig. 147 Glove compart-
ment: tyre control switch After changing the tyre pressure or replacing one or more wheels, the tyre
monitoring indicator must be recalibrated. Do the same, for example, when
the front and rear wheels are swapped.
●
Switch the ignition on.
● Store the new tyre pressure in the Easy Connect system with the button

and the function button Setup ⇒ page 80 or using the switch located in
the glove compartment* ⇒ Fig. 147.
When driving, the system self-calibrates the tyre pressure provided by the
driver and the wheels fitted. After a long journey with varied speeds the pro-
grammed values are collected and monitored.
With the wheels under very heavy loads, the tyre pressure must be in-
creased to the total recommended tyre pressure before the calibration
⇒ page 307.
Note
● The tyre monitoring indicator does not function when there is a fault in
the ESC or ABS ⇒ page 222.
● An erroneous indication may be given when snow chains are in use be-
cause the chains increase the tread of the wheel. 
Parking aid General information
Various systems are available to help you when parking or manoeuvring in
tight spaces, depending on the equipment fitted on your vehicle.
The rear parking aid is an audible assistant that warns about obstacles lo-
cated behind the vehicle ⇒ page 218. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

266Wheels and tyres
–The tyre pressure should only be checked when the tyres are
cold. The slightly raised pressures of warm tyres must not be re-
duced.
– Adjust tyre pressure to the load being carried by the vehicle.
– In vehicles with a tyre pressure indicator, save the pressure of
modified tyres ⇒ page 214, ⇒  page 265.
– Avoid fast cornering and hard acceleration.
– Inspect the tyres for irregular wear from time to time.
The useful life of your tyres depends on the following factors:
Tyre pressure
Tyre pressure values are indicated on the inside of the fuel tank flap.
Insufficient or excessive pressure greatly reduces the useful life of the tyres
and adversely affects vehicle performance and ride. Correct inflation pres-
sures are very important, especially at high speeds.
If you want a more comfortable ride, you can inflate tyres to the pressure
corresponding to the normal vehicle load (up to 3 people) if the vehicle is
carrying a normal load. If the vehicle is going to carry the maximum load,
the tyre pressure should be increased to maximum value indicated.
The tyre pressure must be adjusted according to the load the vehicle is car-
rying. We recommend adhering to the tyre pressure specifications for a max-
imum load.
Do not forget the spare wheel when checking the tyre pressures: Keep the
spare wheel inflated to the highest pressure required for the road wheels.
In the case of a minimised temporary spare wheel (125/70 R16 or 125/70
R18) inflate to a pressure of 4.2 bar as indicated on the tyre pressure label
on the fuel tank flap. Driving style
Fast cornering, heavy acceleration and hard braking (squealing tyres) all in-
crease tyre wear.
Wheel balance
The wheels on new vehicles are balanced. However, certain circumstances
may lead to imbalance (run-out), which is detected as vibrations in the
steering wheel.
Unbalanced wheels should be rebalanced, as they otherwise cause exces-
sive wear on steering, suspension and tyres. A wheel must also be reba-
lanced when a new tyre is fitted or if a tyre is repaired.
Incorrect wheel alignment
Incorrect wheel alignment causes excessive tyre wear, impairing the safety
of the vehicle. If you notice excessive tyre wear, you should check wheel
alignment at a SEAT Official Service.
WARNING
● Always adapt the tyre pressure accordingly when the vehicle load
changes.
● A tyre with low air pressure has to flex a lot more when the vehicle is
heavily loaded or at high speeds, therefore causing overheating to occur.
Under these conditions, the tyre bead may be released or the tyre may
burst. Risk of accident!
For the sake of the environment
Under-inflated tyres will increase fuel consumption. 

269
Wheels and tyres
If you use tyres that are approved by SEAT you can be sure that the actual
tyre dimensions will be correct for your vehicle. If you decide to fit a differ-
ent type of tyre, you must obtain the appropriate manufacturer's certificate
from the tyre retailer to confirm that the tyres are suitable for your vehicle.
Keep this certificate in a safe place.
Your SEAT Official Service will be able to advise you on which tyres may be
fitted to your vehicle.
It is best to have all servicing of wheels and tyres performed by a special-
ised workshop. They are familiar with the procedure and have the necessary
special tools and spare parts as well as the proper facilities for disposing of
the old tyres.
WARNING
● It is very important to ensure that the tyres you have chosen have ad-
equate clearance. When selecting replacement tyres, do not rely entirely
on the nominal tyre size marked on the tyre; with some makes of tyre the
effective tyre size can differ significantly from the nominal dimensions,
even though the tyres have the same size designation. Inadequate tyre
clearance can result in damage to the tyres or the vehicle, causing a seri-
ous safety risk. It may also invalidate the vehicle's registration for use on
public roads.
● Avoid running the vehicle on tyres that are more than 6 years old. If
you have no alternative, you should drive slowly and with extra care at all
times.
● If wheel trims are fitted after the car is purchased, ensure that there
is an adequate flow of air for cooling the brake system.
For the sake of the environment
Old tyres must be disposed of according to the laws in the country con-
cerned.
Note
● Never mount used tyres if you are not sure of their “previous history”.
● For technical reasons, it is not generally possible to use the wheels from
other vehicles. In some cases, this may also be true for the same model of
wheel. 
Wheel bolts
The wheel bolts are designed to suit the rims on your car.
The wheel bolts are matched to the rims. When installing different wheels
(for instance alloy wheels or wheels with winter tyres) it is important to use
the correct wheel bolts with the right length and correctly shaped bolt
heads. This ensures that wheels are fitted securely and that the brake sys-
tem functions correctly.
The wheel bolts must be clean and turn easily.
A special adapter is required to turn the anti-theft wheel bolts*
⇒ page 279. 
Winter tyres
Winter tyres will improve the vehicles handling on snow and
ice.
– Winter tyres must be fitted on all four wheels.
– Only use winter tyres that are approved for your vehicle.
– Please note that the maximum permissible speed for winter
tyres may be lower than for summer tyres. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

277
Emergencies
Note
Do not use the compressor for longer than 6 minutes at a time, as it could
overheat. Once it has cooled down, the compressor may be used again. 
After changing a wheel
– Attach the “max label. 80 km/h” from the tyre repair kit on the
instrument panel, clearly within driver's field of view.
– Stop the vehicle after 10 minutes driving and check the tyre
pressure.
– If tyre pressure is less than 1.3 bar, the tyre is too badly dam-
aged. Do not carry on driving!
WARNING
After repairing a tyre please note the following points:
● Do not drive faster than 80 km/h.
● Avoid heavy acceleration, hard braking and fast cornering.
● Vehicle handling could be impaired.
● If the tyre is very damaged, seek professional assistance.
For the sake of the environment
You can dispose of the used bottle of sealing compound at a SEAT Official
Service.
Note
After repairing a tyre, remember to purchase a new bottle of sealing com-
pound from a SEAT Official Service or a specialised workshop. Changing a wheel
What to do first
Before changing the wheel, the following preliminary steps
are required. – Please observe the important safety notes ⇒ page 274.
– Apply the handbrake.
– Manual gearbox: Select first gear.
– Automatic gearbox: Move the selector lever to P.
– When towing a trailer: Unhitch the trailer from your vehicle.
– Have the vehicle tool kit ⇒ page 274 and the spare wheel ready
⇒ page 282.
WARNING
If you change the wheel on a slope, block the wheel on the opposite side
of the car with a stone or similar to prevent the vehicle from moving.

Safety FirstOperating instructionsPractical TipsTechnical specifications

281
Emergencies
WARNING
● Make sure that the jack* remains stable. If the surface is slippery or
soft, the jack* could slip or sink, respectively, with the resultant risk of
injury.
● Only raise the vehicle with the jack* supplied by the manufacturer.
Other vehicles could slip, with the consequent risk of injury.
● Only mount the jack* on the support points designed for this purpose
on the strut, and always align the jack correctly. If you do not, the jack*
could slip as it does not have an adequate grip on the vehicle: risk of in-
jury!
● The height of the parked vehicle can change as a result of variations
in temperature and loading.
CAUTION
The vehicle must not be raised on the crossbar. Only place the jack* on the
points designed for this purpose on the strut. Otherwise, the vehicle may be
damaged. 
Removing and fitting a wheel
After loosening the wheel bolts and raising the vehicle with the
jack, change the wheel as described below:
Taking off the wheel
– Unscrew the wheel bolts using the box spanner and place them
on a clean surface.
– Take off the wheel ⇒ 
. Putting on the spare wheel
When fitting tyres with a compulsory rotation direction, observe
the instructions in
⇒ page 281.
– Mount the wheel.
– Screw on the wheel bolts in position and tighten them loosely
with a box spanner.
– Carefully lower the vehicle using the jack*.
– Tighten the wheel bolts in diagonal pairs using the wheel
brace.
The wheel bolts should be clean and turn easily. Before fitting the spare
wheel, inspect the wheel condition and hub mounting surfaces. These sur-
faces must be clean before fitting the wheel.
CAUTION
When removing/fitting the wheel, the rim may hit and damage the brake
disc. For this reason, please take care and get a second person to assist
you. 
Tyres with compulsory direction of rotation
A directional tread pattern can be identified by arrows on the sidewall that
point in the direction of rotation. Always observe the direction of rotation in-
dicated when mounting the wheel. This is important so that these tyres can
give maximum grip and avoid excessive noise, tread wear and aquaplaning.
If, exceptionally, it is necessary to mount the spare wheel* in the opposite
direction of rotation, please drive carefully, as in this case the tyre does not
have optimum conditions of use. This is particularly important when driving
on wet roads. 
Safety FirstOperating instructionsPractical TipsTechnical specifications

282Emergencies
To benefit from the advantages of tyres with this type of tread pattern, the
defective tyre should be replaced as soon as possible so that all tyres again
rotate in the correct direction. 
After changing a wheel
– On alloy wheels: replace the wheel bolt caps.
– On plate wheels: replace the wheel hubcap ⇒ page 278.
– Put the tools and jack back in the luggage compartment.
– If the replaced wheel does not fit in the spare wheel housing,
store it safely in the luggage compartment ⇒ page 17.
– Check the tyre pressure of the newly mounted tyre as soon as
possible.
– In vehicles fitted with a tyre pressure indicator, adjust the pres-
sure and store the reading in the radio/Easy Connect system*
⇒ page 214.
– The wheel bolts should be tightened to 120 Nm. Check the tor-
que as soon as possible with a torque wrench. Meanwhile, drive
carefully.
– Have the flat tyre replaced as quickly as possible. Spare wheel
General information
Fig. 171 Compact tem-
porary spare wheel:
raised floor panel
The temporary spare wheel has been designed to be used for short
periods of time. Have the tyres checked, and if necessary, replaced
as soon as possible at a SEAT Official Service or at a specialised
workshop.
Please note the following restrictions when using the compact tem-
porary spare wheel. The compact temporary spare wheel is de-
signed specifically for this model. For this reason, do not use a
temporary spare wheel from a different type of vehicle.
Removing the temporary spare wheel
– Lift and hold up the floor panel to remove the temporary spare
wheel ⇒ Fig. 171.
– Turn the thumb wheel anti-clockwise. 