2013 Seat Exeo ST high beam

84Cockpit
Photosensor/rain sensor faulty 
 Automatic headlights / automatic wipers faulty
If the  symbol lights up, this means that the photosensor/rain sensor is
not working. For safety reasons, the dipped beam headlights will then be
switched on permanently when the light switch is set to the AUTO position.
However, you can still switch the lights on and off in the normal way with
the light switch. If the rain sensor is faulty, the functions operated via the
windscreen wiper lever will still be available. You should have the photosen-
sor/rain sensor checked by a specialised workshop as soon as possible. 
Worn brake pads 
If the  symbol lights up, have the front brake pads (and, for safety rea-
sons, the rear pads as well) inspected by a specialised workshop. 
Speed warning 1 
If the  symbol lights up, this means you are exceeding the speed that has
been pre-set with the speed warning function. You should reduce your
speed accordingly ⇒ page 85. 
Headlight range control faulty 
This symbol  indicates a malfunction in the dynamic headlight range con-
trol. Take the vehicle to a specialised workshop to have the dynamic head-
light range control function repaired. Adaptive headlights* faulty

 Adaptive headlights faulty
This symbol  indicates that the adaptive headlight system is faulty. Take
the vehicle to a specialised workshop to have the headlights or the adap-
tive headlight control unit repaired. 
Washer fluid level low 
If the  symbol lights up, top up the fluid for the windscreen washer and
headlight washer system* ⇒ page 243. 
Speed warning 2 
If the  symbol lights up, this means you are exceeding the speed that has
been pre-set. You should reduce your speed accordingly ⇒ page 85.
Battery voltage too high or too low 
If the  symbol lights up, take the vehicle to a specialised workshop and
have the following items checked:
● Poly V-belt
● Battery condition
It is also advisable to check whether the alternator warning lamp has come
on ⇒ page 72. 

209
Trailer towing
Where possible, operate the trailer with the maximum permitted drawbar
load on the ball joint of the towing bracket, but do not exceed the specified
limit.
Tyre pressure
Check the tyre pressures on your vehicle, and adjust for “full load” condi-
tions (refer to the sticker listing the tyre pressures on the door pillar). It may
also be necessary to adjust the tyre pressures on the trailer according to the
recommendations of the trailer manufacturer.
Exterior mirrors
Check whether you can see enough of the road behind the trailer with the
standard mirrors. If this is not the case you should have additional mirrors
fitted. The two exterior mirrors should be fitted on folding arms. Adjust the
mirrors to give sufficient rear vision.
Headlights
Before starting a journey, check the headlight beam settings with the trailer
hitched up. If necessary, alter the height of the headlight beams by means
of the headlight range control. See ⇒ page 121.
Power supply
When you remove the ignition key, the power supply to the trailer is inter-
rupted.
Removable ball joint coupling
Vehicles with a factory-fitted towing bracket are equipped with a removable
ball joint coupling. This is stored in the spare wheel well in the luggage
compartment together with the necessary fitting instructions.
Note
If you frequently tow, we recommend you also have the vehicle serviced be-
tween services. Notes on towing
Towing a trailer involves additional attention by the driver.
Weight distribution
The weight distribution of a loaded trailer with an unladen vehicle is very
unfavourable. However, if this cannot be avoided, drive extra slow to allow
for the unbalanced weight distribution.
Speed
The stability of the vehicle and trailer is reduced with increasing speed.
Therefore, it is advisable not to drive at the maximum permissible speed in
unfavourable road, weather or wind conditions. This especially applies
when driving downhill.
You should always reduce speed immediately if the trailer shows the slight-
est sign of swaying. Never try to stabilise the trailer by accelerating.
Anticipate hazards and brake in good time. If towing a trailer with an inertia
brake, first brake gently and then harder. This will prevent brake tapping by
the trailer wheels when they lock. Select a low gear in due course before go-
ing down a steep downhill. This enables you to use the engine braking to
slow down the vehicle.
Swaying and pitching can be reduced by stabiliser aids. We recommend
having stabiliser aids installed when towing trailers with a high trailer
weight. They can be purchased and installed at a Technical Service.
Reheating
When climbing long hills in hot weather with the engine running fast in low
gear, you should keep an eye on the coolant temperature gauge ⇒ page 62.
Reduce speed immediately if the needle moves to the right end of the scale.
If the temperature warning lamp  in the instrument panel should start
flashing, stop the vehicle and let the engine cool down by running it at
idling speed for a few minutes. 
Safety FirstOperating instructionsPractical TipsTechnical Specifications

274If and when
Preparation
● Switch off the ignition, lights and all electrical equipment.
● Open the corresponding fuse box ⇒ page 273.
Identifying a blown fuse
A fuse is blown if its metal strip is ruptured ⇒ Fig. 204.
Point a lamp at the fuse. This will make it easier to see if the fuse is blown.
To replace a fuse
● Remove the fuse.
● Replace the blown fuse by one with an identical amperage rating (same
colour and markings) and identical size ⇒ 
.
● Replace the cover again or close the fuse box lid.
CAUTION
If you replace a fuse with higher-rating fuse, you could cause damage to an-
other part of the electrical system. 
Bulbs
General information
You can change the following bulbs for exterior lights yourself:
● Main headlights: all bulbs (except xenon headlights)
● Tail lights: all bulbs
● Side turn signal bulb
The following bulbs can only be changed by a specialised workshop:●
Main headlights: Xenon* bulb ⇒ page 281
● Front fog lights: Bulb
As a rule, you require a certain degree of practical skill to change defective
bulbs. This applies in particular to those bulbs which are only accessible
from the engine compartment.
If in doubt, we recommend that you have defective bulbs changed by a spe-
cialised workshop or qualified mechanic.
If you do decide to change bulbs in the engine compartment yourself, be
aware of the safety risks involved ⇒ page 235 ⇒ 
in Types of bulbs on
page 275.
The name of many of the lamps fitted by SEAT ends in "LL". This means Long
Life. These lamps are used for functions with a long service time (dipped
beam, side lights, daylight driving, etc.). This does not apply to lamps with
a shorter service time (turn signals, etc.). A lamp with the same name ex-
cept for the last two letters, "LL“ or “SLL”, is compatible, but will have a
service life of approximately half of the LongLife lamps.
When replacing lamp bulbs, the same type of bulb as originally fitted
should always be used where possible. 

275
If and when
Changing bulbs. Halogen headlights Types of bulbs
You must only replace a bulb with a bulb of the same type. The name can be
found on the base of the bulb holder.
BulbTypeDipped beam headlights (halogen)12 V/55 W (H7 LL)Main beam headlights12 V/55 W (H1)Turn signal12 V/21 W (PY21W)Side lights12 V/5 W (W5W LL)
WARNING
● Take particular care when working on components in the engine com-
partment if the engine is warm. Risk of burns.
● Bulbs are highly sensitive to pressure. The glass can break when you
touch the bulb, causing injury.
● The high voltage element of gas discharge bulbs* (xenon light) must
be handled correctly. Otherwise, there is a risk of death.
● When changing bulbs, please take care not to injure yourself on sharp
parts in the headlight housing.
CAUTION
● Remove the ignition key before working on the electric system. Other-
wise, a short circuit could occur.
● Switch off the lights or parking lights before you change a bulb.
For the sake of the environment
Please ask your specialist retailer how to dispose of used bulbs in the prop-
er manner.
Note
● Depending on weather conditions (cold or wet), the front lights, the fog
lights, the tail lights and the turn signals may be temporarily misted. This
has no influence on the useful life of the lighting system. By switching on
the lights, the area through which the beam of light is projected will quickly
be demisted. However, the edges may continue to be misted.
● Please check at regular intervals that all lighting (especially the exterior
lighting) on your vehicle is functioning properly. This is not only in the inter-
est of your own safety, but also in that of all other road users.
● Before changing a bulb, make sure you have the correct new bulb.
● Do not touch the glass part of the bulb with your bare hands, use a cloth
or paper towel instead. Otherwise, the fingerprints left on the glass will va-
porise as a result of the heat generated by the bulb, they will be deposited
on the reflector and will impair its surface. 
Safety FirstOperating instructionsPractical TipsTechnical Specifications

282If and when
● Main headlight lamps: Xenon ⇒ 
lights.
● Sources of the DRL (daylight) light unit and position.
WARNING
● Take particular care when working on components in the engine com-
partment if the engine is warm. Risk of burns.
● Bulbs are highly sensitive to pressure. The glass can break when you
touch the bulb, causing injury.
● The high voltage element of gas discharge bulbs* (xenon light) must
be handled correctly. Otherwise, there is a risk of death.
● When changing bulbs, please take care not to injure yourself on sharp
parts in the headlight housing.
CAUTION
● Remove the ignition key before working on the electric system. Other-
wise, a short circuit could occur.
● Switch off the lights or parking lights before you change a bulb.
For the sake of the environment
Please ask your specialist retailer how to dispose of used bulbs in the prop-
er manner.
Note
● Depending on weather conditions (cold or wet), the front lights, the fog
lights, the tail lights and the turn signals may be temporarily misted. This
has no influence on the useful life of the lighting system. By switching on
the lights, the area through which the beam of light is projected will quickly
be demisted. However, the edges may continue to be misted.
● Please check at regular intervals that all lighting (especially the exterior
lighting) on your vehicle is functioning properly. This is not only in the inter-
est of your own safety, but also in that of all other road users. ●
Before changing a bulb, make sure you have the correct new bulb.
● Do not touch the glass part of the bulb with your bare hands, use a cloth
or paper towel instead. Otherwise, the fingerprints left on the glass will va-
porise as a result of the heat generated by the bulb, they will be deposited
on the reflector and will impair its surface. 
Removing the air duct
The air duct has to be removed to gain access to the bulbs
for the right-side headlight.
Fig. 217 Air duct on
right side of vehicle
– Unscrew bolts A
⇒ Fig. 217.
– Detach air duct from guide B
and take it out. 

Head restraintsFront seats . . . . . . . . . . . . . . . . . . . . . . . . . 142
Rear seats . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Removing and fitting . . . . . . . . . . . . . . . . . 142
Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Heated rear window . . . . . . . . . . . . . . . . . . . . . 128 Heating element wires . . . . . . . . . . . . . . . . 222
Heated seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
High pressure cleaners . . . . . . . . . . . . . . . . . . 220
Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
How to jump start description . . . . . . . . . . . . . 296
I
Identification number . . . . . . . . . . . . . . . . . . . 303
Identification plate . . . . . . . . . . . . . . . . . . . . . . 303
Ignition key Safety interlock . . . . . . . . . . . . . . . . . . . . . . 174
Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Indicator lamps Glow plug system . . . . . . . . . . . . . . . . . . . . . 72
Main beam headlights . . . . . . . . . . . . . . . . . 72
Indicator lamps - overview . . . . . . . . . . . . . . . . . 67
Instruments Lighting . . . . . . . . . . . . . . . . . . . . . . . . . 64, 121
Interior lights Ambient lighting . . . . . . . . . . . . . . . . . . . . 126
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Luggage compartment . . . . . . . . . . . . . . . . 127
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 Interior mirror
With manual anti-dazzle setting . . . . . . . . 133
Interior monitoring . . . . . . . . . . . . . . . . . . . . . . 111
Intermittent wipe . . . . . . . . . . . . . . . . . . . . . . . 129
ISOFIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
J
Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261, 266
Jump-starting . . . . . . . . . . . . . . . . . . . . . . . . . . 295
Jump leads . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295
K
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Air conditioner settings . . . . . . . . . . . . . . . 171
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Remote control key . . . . . . . . . . . . . . . . . . . 108
Settings for the driver seat . . . . . . . . . . . . 142
Kick-down feature . . . . . . . . . . . . . . . . . . . . . . . 192
L
Lamps Cruise speed . . . . . . . . . . . . . . . . . . . . . . . . . 69
Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Instruments . . . . . . . . . . . . . . . . . . . . . 64, 121
Lights Adaptive headlights . . . . . . . . . . . . . . . . . . 123
Automatic headlight control . . . . . . . . . . . 117
Coming home function . . . . . . . . . . . . . . . 119
Cornering light . . . . . . . . . . . . . . . . . . . . . . 123 Dipped beam headlights faulty . . . . . . . . . . 85
Dynamic headlight range control . . . . . . . 122
Headlight flasher . . . . . . . . . . . . . . . . . . . . 125
Leaving home function . . . . . . . . . . . . . . . 119
Parking light . . . . . . . . . . . . . . . . . . . . . . . . 125
Reverse lights faulty . . . . . . . . . . . . . . . . . . . 85
Switching on and off . . . . . . . . . . . . . . . . . 117
Xenon lights . . . . . . . . . . . . . . . . . . . . . . . . 122
Load compartment in the luggage compart- ment
see Loading the luggage compartment . . . 16
Loading the luggage compartment . . . . . . . . . . 16
Locking the doors manually if the central lock- ing fails to work
Locking the doors manually if the centrallocking fails to work . . . . . . . . . . . . . . . . 105
Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Long periods of non-use Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Luggage compartment . . . . . . . . . . . . . . . . . . . 145 Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Extending . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Fastening rings . . . . . . . . . . . . . . . . . . . . . . 146
Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Loading . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Luggage compartment liner . . . . . . . . . . . 150
Luggage net . . . . . . . . . . . . . . . . . . . . . . . . 146
Net partition . . . . . . . . . . . . . . . . . . . . . . . . 148
Retaining strap . . . . . . . . . . . . . . . . . . . . . . 147
Side storage compartment . . . . . . . . . . . . 151
Ski bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
see also Loading the luggage compartment . .16
319
Index