2013 RENAULT SCENIC wheel

37B-9
MR-372-J84-37B000$144.mif
V11
ELECTRONIC PARKING BRAKE
Fault finding – System operation
FPA
Vdiag No.: 0C, 04, 08,
0D, 11
37B
MANUAL OPERATION:
– The parking brake is engaged by pulling on the control lever (normal braking immobilises the vehicle).
– Over-application can be obtained by pulling and holding the lever for 5 seconds (maximum application for steep
hills or when the vehicle has reached its maximum permissible all-up weight).
– When the parking brake is applied, the computer super-applies if the force applied to the rear brake callipers is
insufficient (pads cooling) or if the computer detects slight vehicle movement. This detection is limited to
24 hours.
– The parking brake is released when the control lever is applied fully and the release switch is pressed.
ASSISTED OPERATION:
The electronic parking brake enables assisted application and release of the brake:
●Applying the brake: When the engine is switched off, the parking brake is applied when the driver presses the
start button
●Releasing: The brake releases when the drive wheels reach the torque required to move the vehicle
(Note:with automatic transmission, the driver's door must be closed).
Restrictions on assisted brake release in automatic transmissions:
Assisted release is not allowed in the following cases:
– Opening the driver's door followed by engaging a gear (gear lever in position D).
– Engaging a gear (gear lever in position D) followed by opening the driver's door. Note:
When the parking brake is applied, the red light on the instrument panel (brake pads) and indicator light on the
lever are lit.
Below 6 mph (10 km/h) pulling the lever applies the rear brakes. Above 6 mph (10 km/h) pulling the lever
provides dynamic emergency braking without locking the rear wheels (statutory deceleration of 1.5 m/s
2).
The electronic parking brake can only be released when the steering column is unlocked (forced + after ignition
feed, see Introduction).
Note: In this case, the instrument panel displays the message Lever in P or N and the buzzer on the instrument
panel sounds.
Note: In this case, release is authorised for 5 s after the driver's door has been opened (e.g. for a manoeuvre).
After 5 seconds release is prevented.
Note:
Assisted braking and release only occurs if the computer has been configured.
For details on how these configurations function, see Configuration and programming.

37B-10
MR-372-J84-37B000$144.mif
V11
ELECTRONIC PARKING BRAKE
Fault finding – System operation
FPA
Vdiag No.: 0C, 04, 08,
0D, 11
37B
GENERAL OPERATING MODE FOR THE COMPUTER:
The electronic parking brake computer operates in two modes: STANDBY mode and SWITCH ON mode.
●SWITCH ON mode:
Available functions:
– Manual application and release, assisted application and release and emergency braking (steering column
unlocked).
– Full system fault finding (all faults can be identified).
Switch on conditions (3 possibilities):
– The UCH sends a switch on request to the parking brake computer via the multiplex network when the vehicle
is opened or the card is inserted in the reader.
– Braking request via the parking brake control lever.
– Battery voltage more than 13.2 V, if the vehicle has been parked for less than 24 hours.
●STANDBY mode:
Available functions:
– Monitoring of the braking force and slope angle for 24 hours (to ensure parking brake application).
– Only application is authorised (using the lever).
– Restricted system fault finding (the computer can no longer identify all faults).
– Release not authorised.
Conditions for setting to standby:
– The UCH sends a "set to standby" request to the parking brake computer via the multiplex network after the
ignition is switched off and the vehicle is locked (after a few seconds). The parking brake computer's STANDBY
mode will be confirmed by the lever warning light going out (special note: the battery voltage must be less than
13.2 V).
CABLE RESETTING:
The parking brake cable is locked after the control lever is released or after driving at over 1 mph (2 km/h) (switched
on mode).
When the electronic parking brake system locks, it makes a sound that lasts for a few seconds and ends with
clicking (play compensation is automatic).WARNING
Before using the emergency control, it is important to put the vehicle into gear and wedge one wheel if necessary
(on a slope).

37B-25
MR-372-J84-37B000$504.mif
V11
ELECTRONIC PARKING BRAKE
Fault finding – Interpretation of faults37B
DF025
PRESENT
OR
STOREDVEHICLE MOVEMENT WITH MAXIMUM APPLICATION
1. DEF: Rear wheel movement with parking brake applied
2. DEF: Front wheel movement with parking brake applied
NOTESPriorities when dealing with a number of faults:
First deal with faults DF046 Brake motor/cables connection, DF042 Force sensor,
DF035 Undervoltage, DF041 Slope sensor, DF049 Brake application, DF054
Battery voltage too high and DF055 Battery undervoltage, if they are present or
stored.
If none of these faults is present or stored, the parking brake computer is not normally
the cause.
Conditions for applying the fault finding procedure to a stored fault:
Apply the fault finding procedure even if the fault is stored.
Note:
The fault does not remain present after it has been detected.
1. DEF
NOTESSpecial notes:
– This fault indicates that the electronic parking brake
computer detected rear wheel movement although the
parking brake was applied with maximum force.
– It may be associated with 2.DEF.
If this fault is not associated with the faults mentioned
above, check the conformity of the parking brake's
mechanical force line:
– Condition and conformity of rear brake pads.
– Parking brake cables correctly fitted.
– Good condition of the parking brake cables (no seizing
or deterioration).
– Conformity, condition and correct operation of the rear
brake callipers.
This fault is an operational warning. Check the context in
which it appears.
It may appear during:
– incorrect use of a roller test bench which drives the
rear wheels (MOT test),
– forced assisted release when starting, when the
starting conditions have not been met,
– vehicle overload on a very steep slope (maximum
permissible all-up weight exceeded + angle > 18°: e.g.
towing a trailer or a caravan).
AFTER REPAIRIf the computer has been replaced (at the request of the Techline), initialise the
electronic parking brake computer (see Replacement of components).
Issue several braking and release commands to confirm the repair.
Deal with any other faults.
FPA_V0D_DF025/FPA_V11_DF025
FPA
Vdiag No.: 0D, 11

37B-26
MR-372-J84-37B000$504.mif
V11
ELECTRONIC PARKING BRAKE
Fault finding – Interpretation of faults37B
DF025
CONTINUED
2. DEF
NOTESSpecial notes:
– This fault indicates that the electronic parking brake
computer detected front wheel movement although the
parking brake was applied with maximum force.
When this fault appears on its own it is an operating warning
that indicates that the vehicle's conditions of use are on the
limit (the braking system and parking brake are not normally
the cause).
This fault is an operational warning. Check the context in
which it appears.
It may appear during:
– an application request, whilst the vehicle is still being
driven,
– forced assisted release when starting, when the
starting conditions have not been met,
– parked on a steep slope with slippery surface,
– incorrect use of a roller test bench which drives the
front wheels (MOT test).
If the fault is stored, refer to the statuses and
parameters when it appears. Explanation of counters:
seeIntroduction section.
If the fault is stored and PR018 = 0 and PR022 > 25 clear
the fault: do not take this fault into account.
Using the diagnostic tool, display the wheel speed parameters on the parameters screen.
When stationary, these parameters must show 0 mph. If this is not the case, carry out fault finding on the anti-
lock braking system (see 38C, Anti-lock braking system).
Check that the parking brake mechanical tensioning line is correct:
– Parking brake cables correctly fitted.
– Good condition of the parking brake cables (no seizing or deterioration).
– Conformity, condition and proper functioning of the rear brake callipers.
– Condition and conformity of rear brake pads.
Carry out the necessary repairs.
Check that the vehicle is not overloaded.
Check that the vehicle's tyres are not bald.
If the fault persists, contact the Techline.
AFTER REPAIRIf the computer has been replaced (at the request of the Techline), initialise the
electronic parking brake computer (see Replacement of components).
Issue several braking and release commands to confirm the repair.
Deal with any other faults.
FPA
Vdiag No.: 0D, 11

37B-28
MR-372-J84-37B000$504.mif
V11
ELECTRONIC PARKING BRAKE
Fault finding – Interpretation of faults37B
DF025
CONTINUED
Using the diagnostic tool, display the wheel speed parameters on the parameters screen.
When stationary, these parameters must show 0 mph. If this is not the case, carry out fault finding on the anti-lock
braking system.
Check that the parking brake mechanical tensioning line is correct:
– Parking brake cables correctly fitted.
– Good condition of the parking brake cables (no seizing or deterioration).
– Conformity, condition and proper functioning of the rear brake callipers.
– Condition and conformity of rear brake pads.
Carry out the necessary repairs.
Check that the vehicle is not overloaded.
Check that the vehicle's tyres are not bald.
If the fault persists, contact the Techline.
AFTER REPAIRIf the computer has been replaced (at the request of the Techline), initialise the
electronic parking brake computer (see Replacement of components).
Issue several braking and release commands to confirm the repair.
Deal with any other faults.
FPA
Vdiag No.: 0C, 04, 08

37B-79
MR-372-J84-37B000$576.mif
V11
FPA
Vdiag No.: 0C, 04, 08,
0D, 11ELECTRONIC PARKING BRAKE
Fault finding – Conformity check37B
SUB-FUNCTION: AUTOMATIC APPLICATION (CONTINUED 1)
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool.
Application conditions: ignition on (forced + after ignition, see Introduction)
Note:
The interpretation of these statuses and parameters is only valid with the
ignition switched on, the statuses and parameters displayed in blue on the
diagnostic tool is information supplied by other computers, which are transmitted via
the multiplex network. If these variables display inconsistent values, check that the
multiplex system test has not shown up any faulty connections. Repair the faulty
multiplex connections before looking for a possible problem with the signals.
Each sub-function in this test is associated with a Fault finding chart.
Special notes
The diagnostic tool may display the message Computer busy when displaying
statuses and parameters. This message is displayed when the parking brake is
applying or releasing the brake, because the computer gives priority to controlling the
motor before transmitting variables. If this message is displayed, exit the current
screen and then return to it.
Order FunctionParameter or Status
Checked or ActionDisplay and
notesFault finding
4Wheel speedsPR012:Vehicle speedX = 0 mph (km/h)In the event of a fault on this
parameter, check that the anti-
lock braking system computer
is sending the signal correctly
(absence of faults DF037 No
ABS multiplex signal and
DF052 Multiplex network). If
the fault is still present, run
fault finding on the anti-lock
braking system computer (see
38C, Anti-lock braking
system).
5Electronic
parking brakeET011:Parking brakeNo movement of the lever:
INACTIVE
When released: Released
(while releasing, then
INACTIVE).
When applying the brake:
STATUS 1 Static braking
During emergency braking:
STATUS 2 Dynamic braking
(over 6 mph (10 km/h)).
When the system is faulty:
DEFECTIVEIf the status does not operate
as specified, refer to the
interpretation of fault DF043
Parking brake motor.

37B-86
MR-372-J84-37B000$576.mif
V11
FPA
Vdiag No.: 0C, 04, 08,
0D, 11ELECTRONIC PARKING BRAKE
Fault finding – Conformity check37B
SUB-FUNCTION: AUTOMATIC RELEASE (CONTINUED 5)
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool.
Application conditions: ignition on (forced + after ignition, see Introduction)
Note:
The interpretation of these statuses and parameters is only valid with the
ignition switched on, the statuses and parameters displayed in blue on the
diagnostic tool is information supplied by other computers, which are transmitted via
the multiplex network. If these variables display inconsistent values, check that the
multiplex system test has not shown up any faulty connections. Repair the faulty
multiplex connections before looking for a possible problem with the signals.
Each sub-function in this test is associated with a Fault finding chart.
Special notes
The diagnostic tool may display the message Computer busy when displaying
statuses and parameters. This message is displayed when the parking brake is
applying or releasing the brake, because the computer gives priority to controlling the
motor before transmitting variables. If this message is displayed, exit the current
screen and then return to it.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
9Wheel speedsPR012:Vehicle speedX = 0 mph (km/h)In the event of a fault with this
parameter, check that the anti-
lock braking system computer is
sending the signal correctly
(absence of faults DF037 No
ABS system multiplex signal
and DF052 Multiplex network).
If the fault is still present, run
fault finding on the anti-lock
braking system computer (see
38C, Anti-lock braking
system).

37B-89
MR-372-J84-37B000$576.mif
V11
FPA
Vdiag No.: 0C, 04, 08,
0D, 11ELECTRONIC PARKING BRAKE
Fault finding – Conformity check37B
SUB-FUNCTION: EMERGENCY BRAKING
NOTESOnly carry out this conformity check after carrying out a complete check using the
diagnostic tool.
Application conditions: ignition on (forced + after ignition, see Introduction)
Note:
The interpretation of these statuses and parameters is only valid with the
ignition switched on, the statuses and parameters displayed in blue on the
diagnostic tool is information supplied by other computers, which are transmitted via
the multiplex network. If these variables display inconsistent values, check that the
multiplex system test has not shown up any faulty connections. Repair the faulty
multiplex connections before looking for a possible problem with the signals.
Each sub-function in this test is associated with a Fault finding chart.
Special notes
The diagnostic tool may display the message Computer busy when displaying
statuses and parameters. This message is displayed when the parking brake is
applying or releasing the brake, because the computer gives priority to controlling the
motor before transmitting variables. If this message is displayed, exit the current
screen and then return to it.
Order FunctionParameter or Status
Checked or ActionDisplay and notes Fault finding
1EngineET019:EngineSTOPPED
Other possibilities
depending on the
operating status of the
engine:
- RUNNING
- UNDER STARTER
- STALLEDIn the event of a fault with this
status, check that the injection
computer is sending the signal
correctly (absence of faults DF036
No injection multiplex signal
and DF052 Multiplex network).
If the fault is still present, run fault
finding on the injection computer
(see 13B, Diesel injection or
17B, Petrol injection).
2Wheel speedsPR012:Vehicle speedX = 0 mph (km/h)In the event of a fault with these
parameters, check that the anti-
lock braking system computer is
sending the signals correctly
(absence of faults DF037 No ABS
multiplex signal and DF052
Multiplex network). If the fault is
still present, run fault finding on
the anti-lock braking system
computer (see 38C, Anti-lock
braking system). PR013:Rear left-hand
wheel speedX = 0 mph (km/h)
PR014:Rear right-hand
wheel speedX = 0 mph (km/h)