2013 RENAULT SCENIC reset

37B-10
MR-372-J84-37B000$144.mif
V11
ELECTRONIC PARKING BRAKE
Fault finding – System operation
FPA
Vdiag No.: 0C, 04, 08,
0D, 11
37B
GENERAL OPERATING MODE FOR THE COMPUTER:
The electronic parking brake computer operates in two modes: STANDBY mode and SWITCH ON mode.
●SWITCH ON mode:
Available functions:
– Manual application and release, assisted application and release and emergency braking (steering column
unlocked).
– Full system fault finding (all faults can be identified).
Switch on conditions (3 possibilities):
– The UCH sends a switch on request to the parking brake computer via the multiplex network when the vehicle
is opened or the card is inserted in the reader.
– Braking request via the parking brake control lever.
– Battery voltage more than 13.2 V, if the vehicle has been parked for less than 24 hours.
●STANDBY mode:
Available functions:
– Monitoring of the braking force and slope angle for 24 hours (to ensure parking brake application).
– Only application is authorised (using the lever).
– Restricted system fault finding (the computer can no longer identify all faults).
– Release not authorised.
Conditions for setting to standby:
– The UCH sends a "set to standby" request to the parking brake computer via the multiplex network after the
ignition is switched off and the vehicle is locked (after a few seconds). The parking brake computer's STANDBY
mode will be confirmed by the lever warning light going out (special note: the battery voltage must be less than
13.2 V).
CABLE RESETTING:
The parking brake cable is locked after the control lever is released or after driving at over 1 mph (2 km/h) (switched
on mode).
When the electronic parking brake system locks, it makes a sound that lasts for a few seconds and ends with
clicking (play compensation is automatic).WARNING
Before using the emergency control, it is important to put the vehicle into gear and wedge one wheel if necessary
(on a slope).

37B-13
MR-372-J84-37B000$288.mif
V11
37B
ELECTRONIC PARKING BRAKE
Fault finding – Replacement of components
A/ PROCEDURE FOR REPLACING AN ELECTRONIC PARKING BRAKE COMPUTER
●For the description of the mechanical operations for replacing the control unit (computer) and brake cables (see
MR405 (Espace IV) or MR395 (Laguna II) or MR370 (Scénic), Mechanical, 37B, Electronic parking brake,
Control unit: Removal - Refitting and 37A, Mechanical component controls, Parking brake cables:
Removal - Refitting or MR353 (Vel Satis), Mechanical, 37B, Automatic parking brake, Control unit and
brake cables).
●The parking brake cables must always be replaced when the computer is replaced.
●In the same way, the computer must be replaced when the parking brake cables are changed.
●Conversely, the lever and the parking brake are independent of one another.
●Lever replacement must be carried out with + after ignition feed switched off and the parking brake released,
otherwise faults may occur.
●The clutch sensor must be replaced with + after ignition feed switched on to avoid a fault being provoked.
BEFORE REPLACING THE PARKING BRAKE COMPUTER:
If the vehicle has a manual gearbox, recover the clutch data from the memory of the old computer so that it can be
entered into the new computer (see section C).
Operations to perform before replacement:
– Switch on the ignition, connect the diagnostic tool and establish dialogue with the computer (parking
brake field).
– before replacing the computer, check that it is actually causing the fault by reading the faults and apply
the fault finding procedure concerned.
Steps to follow after replacement:
– with the ignition switched off, replace the electronic parking brake computer (with the approval of
Te c h l i n e ) .
– switch on the ignition, connect the diagnostic tool and establish dialogue with the computer (parking
brake field),
– apply the procedure described in section B: NEW COMPUTER CALIBRATION AND INITIALISATION,
– release the parking brake lever to reset the cables.
– check parking brake operation by testing the braking, maximum braking, and release,
– read the faults to clear any stored faults and check that replacing the computer has enabled the fault on
the vehicle to be rectified (no faults present).
– read the configuration (repair mode menu) to check that the parking brake computer configuration has
been correctly configured.
– depending on the configuration chosen, check the assisted braking and release. Note:
An electronic parking brake computer should be replaced only when requested by the Techline (fill out the fault
finding log).
Note:
With an automatic transmission, no data recovery is required (the computer can be replaced without applying
sections C and D).
Important:
Do not clear the faults from the computer before replacing it.
IMPORTANT: It is strictly forbidden to drive a vehicle with an electronic parking brake computer unless it is in
customer mode.
FPA
Vdiag No.: 0C, 04, 08,
0D, 11
MR-372-J84-37B000$288.mif

37B-49
MR-372-J84-37B000$504.mif
V11
ELECTRONIC PARKING BRAKE
Fault finding – Interpretation of faults
FPA
Vdiag No.: 0C, 04, 08,
0D, 11
37B
DF046
PRESENT
OR
STOREDBRAKE MOTOR/CABLES CONNECTION
(EMERGENCY UNLOCKING)
1. DEF: Parking brake unlocked by the emergency handle
NOTESPriority when dealing with a number of faults:
Deal first with faults DF003, DF004, DF028, DF029, DF035, DF041, DF042, DF043,
DF050, DF054, DF055, DF057, DF058 and DF073 if they are present or stored.
Conditions for applying the fault finding procedure to a stored fault:
Apply this fault finding procedure if the fault recurs after the fault is cleared, with the
ignition switched off and on again (forced + after ignition feed, see Introduction),
and the parking brake released then applied using the control lever.
Special notes:
The fault does not usually come from the electronic parking brake computer.
This fault indicates that the electronic parking brake system has been unlocked by the
manual control (if this is the case, check that the handle protector has not been
damaged).
Check that the emergency unlocking handle has not been manually pulled by the
user, which would provoke this fault.
The cables are reset by the parking brake release manual command or automatically
(if the fault is present) when the vehicle is driven at more than 1.2 mph (2 km/h)
(the fault is then stored).
Only for Vdiag 08, 0C and 0D:
If there is a stored fault, refer to the statuses and parameters when it appears.
Explanation of counters: see Introduction.
If the fault is stored and PR018 = 0 and PR022 > 25 clear the fault: do not take this
fault into account.
If there has been no manual use of the emergency unlocking handle and if PR019 > 5,
contact the Techline.
Check that the fault was not provoked by manual usage of the emergency unlocking handle. In this case, it is
normal for the fault to arise; clear the fault.
Carry out a releasing command, then a braking command with the control lever to reset the cables of the parking
brake.
Check the conformity of the parking brake mechanical tensioning line: correctly attached, no breakage.
Check the conformity of the emergency unlocking cable.
Carry out the necessary repairs.
Check that the braking force and maximum braking are operating correctly.
If the fault persists, contact the Techline.
AFTER REPAIRIf the computer has been replaced (at the request of the Techline), initialise the
electronic parking brake computer (see Replacement of components).
Issue several braking and release commands to confirm the repair.
Deal with any other faults.
FPA_V0C_DF046/FPA_V04_DF046/FPA_V08_DF046/FPA_V0D_DF046/FPA_V11_DF046

37B-63
MR-372-J84-37B000$504.mif
V11
ELECTRONIC PARKING BRAKE
Fault finding – Interpretation of faults
FPA
Vdiag No.: 0C, 04, 08,
0D, 11
37B
DF055
PRESENT
OR
STOREDBATTERY UNDERVOLTAGE
1. DEF: Battery voltage too low
2. DEF: Electronic parking brake reset when vehicle being driven
1. DEF
NOTESSpecial notes:
The fault does not usually come from the electronic parking
brake computer.
This fault appears as present if the computer supply voltage
is less than 10.3 V, and becomes stored once the voltage
rises back above 10.5 V.
Only for Vdiag 08, 0C and 0D:
If there is a stored fault, refer to the statuses and
parameters when it appears.
Explanation of counters: see Introduction.
If the fault is stored and PR018 = 0 and PR022 > 25,
clear the fault:
do not take this fault into account.
Note:
This fault may appear if starting is very difficult.
Conditions for applying the fault finding procedure to
a stored fault:
Apply this fault finding procedure if the fault reappears as
present after the ignition has been switched on (forced
+ after ignition feed, see Introduction).
2. DEF
NOTESNote:
This fault only affects Vdiag 0D.
Priorities when dealing with a number of faults:
Deal first with faults DF046 Brake motor/cables
connection, DF042 Force sensor, DF035 Undervoltage,
DF041 Slope sensor, DF049 Brake application, DF054
Battery voltage too high and DF055 Battery
undervoltage if they are present or stored.
If none of these faults is present or stored, the parking brake
computer is not normally the cause.
AFTER REPAIRIf the computer has been replaced (at the request of the Techline), initialise the
electronic parking brake computer (see Replacement of components).
Issue several braking and release commands to confirm the repair.
Deal with any other faults.
FPA_V0C_DF055/FPA_V04_DF055/FPA_V08_DF055/FPA_V0D_DF055/FPA_V11_DF055

37B-64
MR-372-J84-37B000$504.mif
V11
ELECTRONIC PARKING BRAKE
Fault finding – Interpretation of faults
FPA
Vdiag No.: 0C, 04, 08,
0D, 11
37B
DF055
CONTINUED
2. DEF
NOTESSpecial notes:
This fault is generated after the automatic parking brake is
switched on whilst driving or following an internal reset.
With the anti-lock braking system, this detection is active at
> 0.6 mph (> 1 km/h), otherwise the multiplex signal
emitted by the injection computer must be 1.
Note:
The driver is only informed of this fault after 16 successive
detections.
This fault may be due to battery disconnections or vehicle
supply faults, in which case it is associated with fault 1.DEF
(battery voltage too low) dealt with previously.
If the frequency counter (PR016) > 3 and if the onboard network (battery, wiring) analysis does not bring up any
present or stored fault under battery voltage, contact the Techline.
Check that the battery, battery - starter - alternator connection lead, battery earth - chassis lead and the chassis
earth - engine and transmission assembly lead are in good condition.
Repair if necessary.
Check the charging circuit: the alternator should not supply a voltage of less than + 12 V or greater than + 14.4 V
(engine at idle speed).
Carry out the necessary repairs.
track H4
(except Laguna II, Vel Satis and Espace IV)
track G4+12V
track H2
(except Laguna II, Vel Satis and Espace IV)
track G2earth
Repair if necessary (see the vehicle wiring diagram).
If the fault is still present, check that no electrical system using the same supply fuse as the electronic parking
brake computer is faulty.
If the fault persists, contact the Techline.
AFTER REPAIRIf the computer has been replaced (at the request of the Techline), initialise the
electronic parking brake computer (see Replacement of components).
Issue several braking and release commands to confirm the repair.
Deal with any other faults.