2013 RENAULT KANGOO speed

17B-242
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$160.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
ALP 22 Idling speed too high or too low
Check the alternator charge signal module by running TEST 2 Alternator signal module check.
Check the accelerator pedal potentiometer by running TEST 8 Accelerator pedal potentiometer check.
Check the air filter unit.
Check the air inlet temperature sensor by running TEST 6 Checking the air temperature sensor.
Check the throttle valve by running TEST 3 Throttle valve check.
Check the additional fuel circuit solenoid valve by running TEST 5 Checking the additional fuel tank.
Check the coolant temperature sensor by running TEST 15 Coolant temperature sensor check.
Check the spark plugs.
Check the injector rail.
Check the inlet manifold.
Check the additional petrol circuit pump by running TEST 12 Additional fuel tank pump check.
Check the upstream oxygen sensor by running TEST 17 Checking the upstream O2 sensor.
Check the downstream oxygen sensor by running TEST 18 Checking the downstream O2 sensor.
Check the cylinder head.
Check the camshaft.
Check the valves.
Check the timing.
Check the injection computer.
If the fault is still present, contact the techline.
V42_V04_ALP22/V42_V05_ALP22/V42_V06_ALP22/V42_V14_ALP22/V42_V16_ALP22/V42_V18_ALP22

17B-252
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 3 Throttle valve check
NOTESNone.
Check that parameter PR444 Idle speed regulation integral correction is between:
5 N.m < PR444 < 10 N.m (K4M, K7M engine) or -5 N.m < PR444 < 5 N.m (D4D, F4R and K4M engine of Duster).
The attempt is made with the engine idling and warm (75°C), without any electrical consumers switched on. The
value of PR444 must be read at least 20 minutes after the engine coolant temperature has reached 75°C.
If the value of PR444 is greater than 10 N.m (K4M, K7M engine) or 5 N.m (D4D, F4R and K4M engine of Duster),
reprogram the throttle valve using command RZ031 Throttle stop programming.
If the value of PR444 is less than -5 N.m, check the fitting of the throttle and check for possible air leaks (see MR
388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374
(Kangoo VLL), Mechanical, 12A, Fuel mixture, Throttle valve: Removal - Refitting).
If the fault is still present, contact the techline.
V42_V04_TEST3/V42_V05_TEST3/V42_V06_TEST3/V42_V14_TEST3/V42_V16_TEST3/V42_V18_TEST3

17B-259
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 8 Accelerator pedal potentiometer check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the variation in PR055 Engine speed when depressing the accelerator pedal (with the engine running).
Stop the engine and switch on the ignition. Without action on the pedal, check that the voltage correction of circuit 1:
–PR147 Pedal potentiometer voltage gang 1 is less than 817 mV and
–PR148 Pedal potentiometer voltage gang 2 is less than 440 mV.
Next, in the "full load" position, check the circuit 1 voltage PR147, which must be greater than 4185 mV, and
PR148, which must be greater than 2013 mV.
Also check the pedal position in the following cases:
– "position zero" (PR030 Accelerator pedal position = 0)
– "Full load" (PR030 = 1).
Stop the engine and then switch on the ignition.
With the vehicle under + after ignition feed, measure the voltage between the following connections:
–3LR and 3LT of component 921,
–3LU and 3LV of component 921.
If the value is not between 4.75 VX5.25 V, check the insulation, the continuity and the absence of
interference resistance of the following connections:
–3LR between components 120 and 921,
–3LT between components 120 and 921,
–3LU between components 120 and 921,
–3LV between components 120 and 921.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3LS between components 120
and 921,
–3LW between components 120 and 921.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
V42_V04_TEST8/V42_V05_TEST8/V42_V06_TEST8/V42_V14_TEST8/V42_V16_TEST8/V42_V18_TEST8

17B-264
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 10 TDC sensor check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the sensor fitting (connectors, mountings, etc.) (see MR 388 (Logan and Sandero), MR 451 (Duster), MR
423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 17B, Petrol Injection,
Crankshaft position sensor: Removal - Refitting).
Switch on the ignition, check the change of the engine rotation speed using parameter PR055 Engine speed. The
value must be between 0 rpm and more than 120 rpm when the starter is operating.
With the engine running, accelerate to obtain different engine rotation speeds and check that the engine speed
correctly changes in relation to the accelerations.
If PR055 varies, the sensor is sound.
Check the cleanliness and condition of the TDC sensor, component code 149 and of the injection computer
connector, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
V42_V04_TEST10/V42_V05_TEST10/V42_V06_TEST10/V42_V14_TEST10/V42_V16_TEST10/V42_V18_TEST10

17B-272
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 16 Fan relay check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the operation of the low speed fan assembly by running command AC038 Low speed fan assembly relay.
Check the operation of the high speed fan assembly by running command AC039 High speed fan assembly
relay.
If these two checks are correct, the fan assembly relay is not faulty
Run command AC038 and use the test light to check for the control signal of component 120 on connection 3JN
of component 700 (for Logan, Sandero, Duster) or 784 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo VLL).
Check the connection and condition of the fan assembly connector, component code 188 (for Logan, Sandero,
Duster) or 262 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo VLL) and the injection computer connector,
component code 120.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connections:
For Logan, Sandero, Duster:
–3JN between components 700 and 120,
–49C between components 321 and 700,
–49B between components 188 and 321.
For Thalia 2/Symbol 2, Clio II F 6, Kangoo VLL:
–3JN between components 784 and 120,
–49C between components 784 and 321,
–49C between components 262 and 321.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
V42_V04_TEST16/V42_V05_TEST16/V42_V06_TEST16/V42_V14_TEST16/V42_V16_TEST16/V42_V18_TEST16

17B-273
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TEST 16
CONTINUED
Run command AC038 and use the test light to check for the presence of supply at the relay output.
If the supply is absent, replace the low speed fan assembly relay, component code 700 (for Logan, Sandero,
Duster) or 784 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo VLL).
Run command AC039 and use the test light to check for the control signal of component 120 on connection 3JP
of component 336.
Check the insulation, continuity and absence of interference resistance on the following connection:
–49B between components 336 and 188 (for Logan, Sandero, Duster) or 262 (for Thalia 2/Symbol 2, Clio II F
6, Kangoo VLL),
–3JP between components 336 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Run command AC039 and use the test light to check for the presence of supply at the relay output.
If the supply is absent, replace the high speed fan assembly relay, component code 336.
If the fault is still present, contact the techline.

17B-278
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$180.mif
PETROL INJECTION
Fault finding – Tests17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
TDC*: Top Dead Centre
TEST 20 Camshaft sensor check
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Visually inspect the condition of the camshaft sensor.
Check the status of synchronisation of the camshaft sensor with the TDC sensor using ET775 Camshaft TDC*
synchronisation.
Is ET775 "NOT PERFORMED"?
Start the engine. Does the engine start?
With the starter operating, check the status of
synchronisation of the camshaft sensor with the TDC
sensor using ET775.At idle speed and after a few accelerations between
1000 and 2000 rpm, check the status of
synchronisation of the camshaft sensor with the TDC
sensor using ET775.
Is ET775 "PERFORMED"?Is ET775 "PERFORMED"?
The camshaft sensor is
correct.The camshaft sensor is
correct.
YES
NO
A
NOYES
YESNO
A
YESNO
A
V42_V04_TEST20/V42_V05_TEST20/V42_V06_TEST20/V42_V14_TEST20/V42_V16_TEST20/V42_V18_TEST20