2013 RENAULT KANGOO 6015A

17B-129
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF974
PRESENT OR
STOREDPEDAL POTENTIOMETER CIRCUIT GANG 11.DEF: Battery voltage too high.
2.DEF: Battery voltage too low.
NOTESFault priorities:
Deal with the following fault as a priority:
DF011 Sensor voltage supply no. 1
Special notes:
After this fault appears:
The OBD and level 1 warning lights are illuminated.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and condition of the connector of the accelerator pedal sensor, gang 1, component code
921 and of the injection computer connector, component code 120.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Run TEST 8 Accelerator pedal potentiometer check.
If the fault is still present, contact the Techline.
V42_V04_DF974/V42_V05_DF974/V42_V06_DF974/V42_V14_DF974/V42_V16_DF974/V42_V18_DF974

17B-130
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF975
PRESENT OR
STOREDPEDAL POTENTIOMETER CIRCUIT GANG 21.DEF: Battery voltage too high.
2.DEF: Battery voltage too low.
NOTESSpecial notes:
After this fault appears:
The OBD and level 1 warning lights are illuminated.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the connection and condition of the connector of the accelerator pedal sensor, gang 2, component code
921 and of the injection computer connector, component code 120.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Run TEST 8 Accelerator pedal potentiometer check.
If the fault is still present, contact the Techline.
V42_V04_DF975/V42_V05_DF975/V42_V06_DF975/V42_V14_DF975/V42_V16_DF975/V42_V18_DF975

17B-131
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF992
PRESENT OR
STOREDADDITIONAL HEATER 1 RELAY CIRCUITCC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness and condition of the additional heater 1 relay, component code 1067 and the connections
of the injection computer, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
–38JU between components 1067 and 120,
–3FB between components 1067 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the additional heater relay operates correctly by running command AC250 Heating resistor 1 relay
and check that there are no more faults on the relay. If the check is not correct, replace the additional heater relay,
component code 1067 (see MR 388 or 451, Mechanical, 61A, Heating system, Heating resistor relay:
Removal - Refitting).
If the fault is still present, contact the Techline.
V42_V04_DF992/V42_V05_DF992/V42_V06_DF992/V42_V14_DF992/V42_V16_DF992/V42_V18_DF992

17B-132
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF993
PRESENT OR
STOREDADDITIONAL HEATER 2 RELAY CIRCUITCC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness and condition of the additional heater 2 relay, component code 1068 and the connections
of the injection computer, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
–38JV between components 1068 and 120,
–3FB between components 1068 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the additional heater relay operates correctly by running command AC251 Heating resistor 2 relay
and check that there are no more faults on the relay. If the check is not correct, replace the additional heater relay,
component code 1068 (see MR 388 or 451, Mechanical, 61A, Heating system, Heating resistor relay:
Removal - Refitting).
If the fault is still present, contact the Techline.
V42_V04_DF993/V42_V05_DF993/V42_V06_DF993/V42_V14_DF993/V42_V16_DF993/V42_V18_DF993

17B-133
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF994
PRESENT OR
STOREDADDITIONAL HEATER 3 RELAY CIRCUITCC.0: Short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit
NOTESSee the Wiring Diagrams Technical Note for Logan, Sandero, Duster.
Check the cleanliness and condition of the additional heater 3 relay, component code 1069 and the connections
of the injection computer, component code 120.
If the connector or connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing
electrical wiring, Wiring: Precautions for repair), repair the connector(s), otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
–38JW between components 1069 and 120,
–3FB between components 1069 and 1047.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check that the additional heater relay operates correctly by running command AC252 Heating resistor 3 relay
and check that there are no more faults on the relay. If the check is not correct, replace the additional heater relay,
component code 1069 (see MR 388 or 451, Mechanical, 61A, Heating system, Heating resistor relay:
Removal - Refitting).
If the fault is still present, contact the Techline.
V42_V04_DF994/V42_V05_DF994/V42_V06_DF994/V42_V14_DF994/V42_V16_DF994/V42_V18_DF994

17B-135
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF1015
CONTINUED
– With the brake pedal depressed, measure the resistance of the brake pedal switch, component code 160
between connections AP1 (for Logan, Sandero, Duster) or AP10 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo
VLL) and 65A. The value must be X > 10 M (between 0°C and 40°C).
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), Mechanical, 37A, Mechanical component controls,
Brake pedal switch: Removal - Refitting or MR 430 (Clio II F 6), MR 374 (Kangoo VLL), Mechanical, 37A,
Mechanical component controls, Brake pedal: Removal - Refitting).
– With the brake pedal released, measure the resistance of the brake pedal switch, component code 160
between connections AP1 (for Logan, Sandero, Duster) or AP10 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo
VLL) and 5A, the value must be between 0  < X  1 (between 0°C and 40°C).
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), Mechanical, 37A, Mechanical component controls,
Brake pedal switch: Removal - Refitting or MR 430 (Clio II F 6), MR 374 (Kangoo VLL), Mechanical, 37A,
Mechanical component controls, Brake pedal: Removal - Refitting).
Check the brake pedal switch connector, component code 160 (see MR 388 (Logan and Sandero), MR 451
(Duster), MR 423 (Thalia 2/Symbol 2), Mechanical, 37A, Mechanical component controls, Brake pedal
switch: Removal - Refitting or MR 430 (Clio II F 6), MR 374 (Kangoo VLL), Mechanical, 37A, Mechanical
component controls, Brake pedal: Removal - Refitting).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair
), repair the connector, otherwise replace the wiring.
Check fuse F03 (for Logan, Sandero, Duster), F4 (for Thalia 2/Symbol 2, Clio II F 6 or F16 (for Kangoo VLL)
and replace it if necessary.
If the fault is still present, contact the Techline.

17B-137
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF1016
CONTINUED
Part 2:
Check the connector of the clutch pedal position sensor, component code 675.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connections:
–86D between components 675 and 120,
–MAM or M between earth and component 675.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.

17B-141
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF1058
PRESENT OR
STOREDINLET PRESSURE CONSISTENCY1.DEF: Abnormal voltage
2.DEF: Abnormal pressure
NOTESPriority when dealing with a number of faults:
DF079 Motorised throttle valve servo
Conditions for applying the fault finding procedure to a stored fault:
The fault is considered present under the following conditions:
–For 2.DEF engine running at idle speed.
Special note:
For 2.DEF, the OBD warning light and level 1 fault warning light illuminate,
For 1.DEF, the OBD warning light illuminates.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
Check the fitting and sealing of the inlet air pressure sensor, component code 147 (condition of the seals) and look
for possible leaks on the inlet air pipe.
Check the connector of the inlet air pressure sensor, component code 147.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the supply voltage of the sensor on connections 3AJR and 3AJP.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3AJP between components 120 and 147,
–3AJR between components 120 and 147,
–3AJQ between components 120 and 147.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Replace the inlet air pressure sensor, component code 147 and check that the fault is no longer present (see MR
388 (Logan and Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374
(Kangoo VLL), Mechanical, 12A, Fuel mixture, Air inlet: Description).
If the fault is still present, contact the Techline.
V42_V04_DF1058/V42_V05_DF1058/V42_V06_DF1058/V42_V14_DF1058/V42_V16_DF1058/V42_V18_DF1058