2013 RENAULT KANGOO brake

17B-124
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$083.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF887
PRESENT OR
STOREDBRAKE - ACCELERATOR PEDAL POSITION1.DEF: Jammed accelerator pedal detected.
2.DEF: Jammed accelerator pedal detected.
3.DEF: Inconsistency between pedal gang 1 and gang 2.
4. DEF: Fault on pedal potentiometer gangs 1 and 2.
NOTESConditions for application to a stored fault:
The fault is declared present after the ignition is switched on or with the engine running.
Deal with the stored faults (1.DEF, 2.DEF only).
Special notes:
After this fault appears:
For 3.DEF, the OBD and level 1 warning lights are illuminated.
For 2.DEF and 4.DEF, the OBD and level 2 warning lights are illuminated.
1.DEF
2.DEF
NOTESNone.
Check that the accelerator pedal is not jammed and that there is nothing impeding its operation (floor carpet, etc.).
Run TEST 9 Brake pedal switch check.
Run TEST 8 Accelerator pedal potentiometer check.
If the fault is still present, contact the Techline.
V42_V04_DF887/V42_V05_DF887/V42_V06_DF887/V42_V14_DF887/V42_V16_DF887/V42_V18_DF887

17B-134
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF1015
PRESENT OR
STOREDBRAKE SWITCH SIGNAL CONSISTENCY
1.DEF: Value outside permitted tolerance values
2.DEF: Inconsistent signal.
NOTESFault priorities
Deal with the following faults first:
DF050 Brake switch circuit
DF631 Brake light switch signal
Conditions for application to a stored fault:
The fault is declared present:
–For 1.DEF engine at idle speed.
–For 2.DEF, if impossible to see the fault present, deal with it as stored.
See the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2, Clio II F 6, Kangoo VLL.
With the brake pedal released, check ET039 Brake pedal and ET799 Brake wire contact.
If ET039 is Released and ET799 is Inactive.
Check the fitting and mechanical operation of the brake pedal (the pedal returns properly).
If the check is incorrect, check the braking system.
Remove the brake pedal switch, component code 160 (see MR 388 (Logan and Sandero), MR 451 (Duster),
MR 423 (Thalia 2/Symbol 2), Mechanical, 37A, Mechanical component controls, Brake pedal switch:
Removal - Refitting or MR 430 (Clio II F 6), MR 374 (Kangoo VLL), Mechanical, 37A, Mechanical component
controls, Brake pedal: Removal - Refitting) and, without depressing the pedal, press sufficiently on the brake
pedal switch to seat it completely in its position.
Lock it by turning it an eighth of a turn.
The fault should change from present to stored.
V42_V04_DF1015/V42_V05_DF1015/V42_V06_DF1015/V42_V14_DF1015/V42_V16_DF1015/V42_V18_DF1015

17B-135
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF1015
CONTINUED
– With the brake pedal depressed, measure the resistance of the brake pedal switch, component code 160
between connections AP1 (for Logan, Sandero, Duster) or AP10 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo
VLL) and 65A. The value must be X > 10 M (between 0°C and 40°C).
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), Mechanical, 37A, Mechanical component controls,
Brake pedal switch: Removal - Refitting or MR 430 (Clio II F 6), MR 374 (Kangoo VLL), Mechanical, 37A,
Mechanical component controls, Brake pedal: Removal - Refitting).
– With the brake pedal released, measure the resistance of the brake pedal switch, component code 160
between connections AP1 (for Logan, Sandero, Duster) or AP10 (for Thalia 2/Symbol 2, Clio II F 6, Kangoo
VLL) and 5A, the value must be between 0  < X  1 (between 0°C and 40°C).
If the resistance is not correct, replace the brake pedal switch, component code 160 (see MR 388 (Logan and
Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), Mechanical, 37A, Mechanical component controls,
Brake pedal switch: Removal - Refitting or MR 430 (Clio II F 6), MR 374 (Kangoo VLL), Mechanical, 37A,
Mechanical component controls, Brake pedal: Removal - Refitting).
Check the brake pedal switch connector, component code 160 (see MR 388 (Logan and Sandero), MR 451
(Duster), MR 423 (Thalia 2/Symbol 2), Mechanical, 37A, Mechanical component controls, Brake pedal
switch: Removal - Refitting or MR 430 (Clio II F 6), MR 374 (Kangoo VLL), Mechanical, 37A, Mechanical
component controls, Brake pedal: Removal - Refitting).
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair
), repair the connector, otherwise replace the wiring.
Check fuse F03 (for Logan, Sandero, Duster), F4 (for Thalia 2/Symbol 2, Clio II F 6 or F16 (for Kangoo VLL)
and replace it if necessary.
If the fault is still present, contact the Techline.

17B-140
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF1034
CONTINUED
After repair, check that the catalytic converter was not damaged by the misfire.
To do this, switch on the ignition, run the catalytic converter test SC006 Run OBD test: Catalytic converter and
start the engine (only depress the brake pedal to authorise the starting of the engine,
Do not depress the accelerator pedal or the clutch pedal).
At the end, check the test results:
STATUS1: Fault finding was not performed/impossible to obtain the necessary conditions
STATUS2: The component is in an average condition - sensor OK
STATUS3: The component is in a good condition - sensor OK
STATUS4: The component is in poor condition - replace the catalytic converter (see MR 451 (Duster), MR 423
(Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 19B, Exhaust, Catalytic
converter: Removal - Refitting).
Note: The catalytic converter procedure is not carried out if a fault is present.
Important: Do not run the procedure if a new catalytic converter is fitted.
2.DEF
NOTESNone.
Check the ignition coil circuit of cylinder 3,
Check the fuel supply circuit (see MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374
(Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit: Operating diagram),
Check the fuel supply pump circuit,
Check the condition of the cylinder 3 injector (see MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio
II F 6) or MR 374 (Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal -
Refitting),
Check the compression of cylinder 3.

17B-161V2 MR-376-X76-17B050$100.mif
17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
Tool status Diagnostic tool title
ET001Computer + After ignition
ET038Engine
ET039Brake pedal
ET041Gearbox ratio
ET047Fuel pump control circuit
ET051Throttle stop programming
ET089Flywheel target programming
ET148OBD warning light activation request
ET321Air conditioning compressor
ET405Clutch pedal switch
ET434Low fuel level
ET571LPG minimum signal
ET673Jammed accelerator pedal detected
ET717Target gearbox ratio
ET734Heating resistor 1 relay control
ET735Heating resistor 2 relay control
ET736Heating resistor 3 relay control
ET759Braking multiplex signal detected
ET760First starting
ET775Camshaft TDC* synchronisation
ET798Clutch wire contact connection
ET799Brake wire contact
PETROL INJECTION
Fault finding – Status summary table

17B-173V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET673JAMMED ACCELERATOR PEDAL
STATUS DEFINITIONYES: This status indicates that the accelerator pedal is jammed.
NO: This status indicates that the accelerator pedal is not jammed.
NOTESTo reinitialise this status, clear the fault memory by running command RZ001 Fault
memory.
Conformity check: Engine stopped, ignition on or engine running.
YESCheck that the accelerator pedal is not jammed or that there is nothing impeding its
operation (floor carpet, etc.).
Check the brake switch (see the interpretation of fault DF050 Brake switch circuit.
V42_V04_ET673/V42_V05_ET673/V42_V06_ET673/V42_V14_ET673/V42_V16_ET673/V42_V18_ET673

17B-176V2 MR-376-X76-17B050$110.mif
PETROL INJECTION
Fault finding – Interpretation of statuses17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET759BRAKING MULTIPLEX SIGNAL DETECTED
STATUS DEFINITIONABSENT: This status indicates that the braking multiplex signal detected is absent.
PRESENT: This status indicates that the braking multiplex signal detected is present.
INTERMEDIATE: This status indicates that the braking multiplex signal detected is
intermediate.
Conformity check: Engine stopped, ignition on or engine running.
Vehicle under + after ignition feed.
– Parking brake released,
– Gear lever in 1
st.
Neither the brake pedal nor the clutch pedal depressed.
Check status ET759.
PRESENT -
INTERMEDIATECheck the correct position and the conformity of the brake pedal sensor.
Run fault finding on the UCH domain (see 87B, UCH).
"ABSENT"The brake pedal sensor is correct.
V42_V04_ET759/V42_V05_ET759/V42_V06_ET759/V42_V14_ET759/V42_V16_ET759/V42_V18_ET759

17B-182V2 MR-376-X76-17B050$120.mif
PETROL INJECTION
Fault finding – Parameter summary table17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
Refriger.*: refrigerant
Syncro*: Synchronisation
OCR*: Opening cyclic ratio
CS*: CamshaftTool
ParameterDiagnostic tool title
PR832Combustion misfiring counter
PR833Combustion misfiring counter
PR834Combustion misfiring counter
PR847Inlet air temperature sensor voltage
PR872Refriger.* pressure sensor voltage
PR876CS* dephaser solenoid valve control OCR*
PR877Estimated engine oil temperature
PR887Motorised throttle safe mode programmed value
PR931Raw turbocharging pressure
PR1026Crankshaft synchro.* loss counter
PR1029 Alternator power
PR1116LPG pressure
PR1129 Brake contact no.1 duration
PR1153 Brake contact no.2 duration
PR1198LPG temperature
PR1232Number of engine rotations