2013 RENAULT KANGOO catalytic converter

17B-140
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
V2 MR-376-X76-17B050$084.mif
PETROL INJECTION
Fault finding – Interpretation of faults17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
DF1034
CONTINUED
After repair, check that the catalytic converter was not damaged by the misfire.
To do this, switch on the ignition, run the catalytic converter test SC006 Run OBD test: Catalytic converter and
start the engine (only depress the brake pedal to authorise the starting of the engine,
Do not depress the accelerator pedal or the clutch pedal).
At the end, check the test results:
STATUS1: Fault finding was not performed/impossible to obtain the necessary conditions
STATUS2: The component is in an average condition - sensor OK
STATUS3: The component is in a good condition - sensor OK
STATUS4: The component is in poor condition - replace the catalytic converter (see MR 451 (Duster), MR 423
(Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374 (Kangoo VLL), Mechanical, 19B, Exhaust, Catalytic
converter: Removal - Refitting).
Note: The catalytic converter procedure is not carried out if a fault is present.
Important: Do not run the procedure if a new catalytic converter is fitted.
2.DEF
NOTESNone.
Check the ignition coil circuit of cylinder 3,
Check the fuel supply circuit (see MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio II F 6) or MR 374
(Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel circuit: Operating diagram),
Check the fuel supply pump circuit,
Check the condition of the cylinder 3 injector (see MR 451 (Duster), MR 423 (Thalia 2/Symbol 2), MR 430 (Clio
II F 6) or MR 374 (Kangoo VLL), Mechanical, 17B, Petrol injection, Injector rail - Injectors: Removal -
Refitting),
Check the compression of cylinder 3.

17B-214V2 MR-376-X76-17B050$140.mif
PETROL INJECTION
Fault finding – Command summary table17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
AC217Additional fuel circuit
solenoid valveThis command is used to check the additional fuel circuit
solenoid valve. Only on Flexfuel injection
AC224Additional fuel circuit pump
relay This command is used to check the relay of the additional circuit
pump. Only on Flexfuel injection
AC250 Heating resistor 1 relayThis command is used to activate the heating resistor no.1 relay.
AC251 Heating resistor 2 relayThis command is used to activate the heating resistor no.2 relay.
AC252 Heating resistor 3 relayThis command is used to activate the heating resistor no.3 relay.
SC001 Write saved dataUse this command after replacing or (re)programming the
computer (if the data has been saved using command SC003).
SC003 Save computer dataThis command enables the computer operating data, the engine
adaptives, to be recorded.
SC006Start OBD test: Catalytic
converterThis command is used to test the catalytic converter.
SC007 Run OBD test: O2 sensorThis command is used to test the O2 sensors.
SC061Oil change interval (OCS)
OxidationThis command is used to perform a test on the oil oxidation (see
Technical Note 6523A, Oil change interval (OCS) fault finding
for petrol and diesel engines)
VP010 Enter VIN.This command is used to enter the VIN.
VP036 Fuel supply inhibitedThis command is used to inhibit fuel supply to the engine.

17B-221
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$160.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
ALP 2 General appearance of engine compartment
Check the fan assembly
Check the air filter unit.
Check the inlet manifold air pressure sensor by running TEST 7 Air inlet pressure sensor check.
Check the air pipes.
Check the coolant temperature sensor by running TEST 15 Coolant temperature sensor check.
Check the injector rail.
Check the inlet manifold.
Check the oil filter.
Check the catalytic converter.
Check the exhaust manifold.
Check the accessories belt.
Check the dipstick.
If the fault is still present, contact the techline.
V42_V04_ALP2/V42_V05_ALP2/V42_V06_ALP2/V42_V14_ALP2/V42_V16_ALP2/V42_V18_ALP2

17B-222
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$160.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
ALP 3 Appearance and mounting of the exhaust
Check the catalytic converter.
Check the exhaust manifold.
Check the cylinder head.
If the fault is still present, contact the techline.
V42_V04_ALP3/V42_V05_ALP3/V42_V06_ALP3/V42_V14_ALP3/V42_V16_ALP3/V42_V18_ALP3

17B-226
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$160.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
ALP 7 Unusual odour
Check the air pipes.
Check the catalytic converter.
Check the coolant pump.
Check the exhaust manifold.
Check the cylinder head.
Check the timing.
Check the cooling system.
If the fault is still present, contact the techline.
V42_V04_ALP7/V42_V05_ALP7/V42_V06_ALP7/V42_V14_ALP7/V42_V16_ALP7/V42_V18_ALP7

17B-228
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$160.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
ALP 9 Abnormal smoke in the engine compartment
Check the air pipes.
Check the injector rail.
Check the inlet manifold.
Check the oil circuit.
Check the catalytic converter.
Check the coolant pump.
Check the exhaust manifold.
Check the cylinder head.
Check the timing.
Check the cooling system.
If the fault is still present, contact the techline.
V42_V04_ALP9/V42_V05_ALP9/V42_V06_ALP9/V42_V14_ALP9/V42_V16_ALP9/V42_V18_ALP9

17B-232
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$160.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
ALP 13 Excessive fuel consumption
Check the air filter unit.
Check the air pipes.
Check the additional fuel circuit solenoid valve by running TEST 5 Checking the additional fuel tank.
Check the injector rail.
Check the injectors by running TEST 13 Checking the injectors.
Check the additional petrol circuit pump by running TEST 12 Additional fuel tank pump check.
Check the pinking sensor by running TEST 11 Pinking sensor check.
Check the upstream oxygen sensor by running TEST 17 Checking the upstream O2 sensor.
Check the downstream oxygen sensor by running TEST 18 Checking the downstream O2 sensor.
Check the catalytic converter.
Check the camshaft.
If the fault is still present, contact the techline.
V42_V04_ALP13/V42_V05_ALP13/V42_V06_ALP13/V42_V14_ALP13/V42_V16_ALP13/V42_V18_ALP13

17B-239
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V2 MR-376-X76-17B050$160.mif
PETROL INJECTION
Fault finding – Fault Finding Chart17B
V42 Injection
Program No.: 2A
Vdiag No.: 04, 05, 06,
14, 16, 18
ALP 19
CONTINUED
Check the downstream oxygen sensor by running TEST 18 Checking the downstream O2 sensor.
Check the catalytic converter.
Check the exhaust manifold.
Check the pistons and piston rings.
Check the cylinder head.
Check the camshaft.
Check the valves.
Check the timing.
Check the rotating parts.
Check the injection computer.
If the fault is still present, contact the techline.