2013 RENAULT KANGOO Lighting Workshop Manual

80D-25
AFTER REPAIRCarry out a road test and then a check using the diagnostic tool.
V1 MR-376-X76-80D000$100.mif
LIGHTING
Fault finding – Interpretation of commands80D
UCH
Vdiag No.: 0F
AC145FRONT COURTESY LIGHTS
NOTESThis command is used to activate the front courtesy light.
There must be no present or stored faults.
Check the conformity of the courtesy light bulbs.
Switch on the ignition.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check the connection and condition of the courtesy light console, component code 265 and the UCH connector,
component code 645.
If the connector(s) are faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity between the following connections:
•BPT between components 265 and 645,
•13E between components 265 and 645,
•MK between components 265 and earth.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
Check the continuity of connection MK of component 265.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the techline.
UCH_V0F_AC145

80D-26V1 MR-376-X76-80D000$110.mif
80D
UCH
Vdiag No.: 0F
NOTESOnly refer to these customer complaints after carrying out a complete check with
the diagnostic tool
LIGHTING
The direction indicator lights do not work ALP 2
Side lights do not operate ALP 3
The reversing lights do not operate ALP 10
LIGHTING
Fault finding – Customer complaints

80D-27
AFTER REPAIRCheck the system operation.
V1 MR-376-X76-80D000$120.mif
80D
UCH
Vdiag No.: 0F
ALP 2 The direction indicator lights do not work
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
Check the bulbs.
Special Note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check for the presence and condition of fuse F31 (10 A) on the passenger compartment fuse and relay box,
component code 260 (see MR 374 Mechanical, 81C, Fuses, Fuses: List and location of components).
Press the hazard warning lights switch and check that status ET485 Hazard warning lights signal is PRESENT;
if not, refer to the interpretation of this status.
Activate the right-hand or left-hand indicator and check that ET486 Right-hand indicator signal and ET487 Left-
hand indicator signal are PRESENT. If not, refer to the interpretation of these statuses.
Check the condition of the UCH connector, component code 645.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity of the following connections:
•64C between components 645 and 256, then 173, then 268,
•64D between components 645 and 255, then 172, then 267.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.
UCH_V0F_ALP02
LIGHTING
Fault finding – Fault Finding Chart

80D-28
AFTER REPAIRCheck the system operation.
V1 MR-376-X76-80D000$120.mif
LIGHTING
Fault finding – Fault Finding Chart80D
UCH
Vdiag No.: 0F
ALP 3 Side lights do not operate
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
Check the bulbs.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Activate the side lights control and check that status ET484 Side lights signal is PRESENT; if not, refer to the
interpretation of this status.
Check for the presence and condition of fuses F31 and F32 (10 A) on the passenger compartment fuse and relay
box, component code 260 (see MR 374, Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the continuity of the following connections:
•LPG between components 185 and 260,
•LPG between components 173 and 260,
•LPG between components 167 and 260,
•LPD between components 184 and 260,
•LPD between components 172 and 260,
•LPG between components166 and 260.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
Check for earths on the following connections:
•MQ of component 184,
•MB of component 185,
•MG of component 173,
•MF of component 172,
•MG of components 166 and 167.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair) repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.
UCH_V0F_ALP03

80D-29
AFTER REPAIRCarry out a check using the diagnostic tool.
V1 MR-376-X76-80D000$120.mif
LIGHTING
Fault finding – Fault Finding Chart80D
UCH
Vdiag No.: 0F
ALP 10 The reversing lights do not operate
Check for the presence and condition of fuse
F14 (15 A) in the passenger compartment fuse
and relay box, component code 260.
Is the result of the check correct? Replace the fuse if necessary (see MR
374, Mechanical, 81C, Fuses, Fuses:
List and location of components).
Check the bulbs and condition of the bulb
supports.
Are the checks correct?Replace the bulbs if necessary (see MR
374 Mechanical, 81A, Rear lighting,
Rear light bulb: Removal - Refitting).
Check the condition and connection of the
connectors of components 155 and 172.
Are the checks correct?If the connector or connectors are faulty
and there is a repair procedure (see
Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for
repair), repair the connector, otherwise
replace the wiring.
Check for earth on the following connections:
–MF between component 172 and earth.
Is it correct?If the connection or connections are faulty
and there is a repair procedure (see
Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise
replace it.
NO
YES
NO
YES
NO
YES
NO
YES
A
UCH_V0F_ALP10

80D-30
AFTER REPAIRCarry out a check using the diagnostic tool.
V1 MR-376-X76-80D000$120.mif
LIGHTING
Fault finding – Fault Finding Chart80D
UCH
Vdiag No.: 0F
ALP 10
CONTINUED
Check the operation of the reversing lights
switch, component code 155 while making a
direct connection:
– between AP3 and H66P of component 155.
Does the reversing light illuminate?Replace the reversing lights switch,
component code 155.
Check the continuity, insulation and absence
of interference resistance on the following
connections:
–H66P between components 155 and 172.
–AP3 between components 260 and 155.
Are the checks correct?If the connection or connections are
faulty and there is a repair procedure
(see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for
repair), repair the connector, otherwise
replace the wiring.
If the fault is still present, contact Techline
A
YES
YES
NO
NO
YES