2013 RENAULT KANGOO diagram

13B-108
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF242
PRESENT
OR
STOREDENGINE SPEED SIGNAL OUTPUT
CC.1: Short circuit to + 12 V
CO.0: Open circuit or short circuit to earth
NOTESPriority when dealing with a number of faults:
– DF113 Sensor supply voltage, deal with fault DF113 first.
Special notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the connection and condition of the engine speed sensor connector, component code 149.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3BG between components 120 and 149,
●3BL between components 120 and 149.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Measure the resistance of the engine speed sensor, component code 149 between connections 3BG and 3BL:
510  < X < 850  at 20°C
If the value is not correct, replace the engine speed sensor (see MR 388 (Logan/Sandero), MR 451 (Duster), MR
423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 13B, Diesel injection, Crankshaft position
sensor: Removal – Refitting).
If the fault is still present, contact the Techline.
DCM1.2_V08_DF242

13B-109
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF261
PRESENT
OR
STOREDTURBOCHARGER ACTUATOR CIRCUIT
CC.1: Short circuit to + 12 V
CO.0: Open circuit or short circuit to earth
NOTESSpecial notes:
If fault DF261 is present, the air flow regulation is switched off, the EGR valve is closed,
and the turbocharging regulation is switched off.
Injection defective message displayed on the instrument panel and reduced
performance.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Run TEST 11 Air line at the turbocharger.
Run TEST 5 Inlet circuit check.
Run TEST 10 Turbocharger solenoid valve check.
Run Test 12 Turbocharger.
Check the inlet pressure signal, check the gear number when changing gear.
If the fault is still present, contact the Techline.
DCM1.2_V08_DF261

13B-110
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF427
PRESENT
OR
STOREDTURBO ACTUATOR CONTROL
1.DEF: At minimum stop
2.DEF: At maximum stop
NOTESSpecial notes:
If fault DF427 is present, the air flow regulation is switched off, the EGR valve is closed,
the turbocharging regulation is switched off and reduced performance.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Run TEST 11 Air line at the turbocharger.
Run TEST 5 Inlet circuit check.
Run TEST 10 Turbocharger solenoid valve check.
Run Test 12 Turbocharger.
Check the turbocharging pressure signal, check the gear number when changing gear.
If the fault is still present, contact the Techline.
DCM1.2_V08_DF427

13B-112
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF489
PRESENT
OR
STOREDAIR CONDITIONING COMPRESSOR CONTROL
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to + 12 V
NOTESCondition for applying the fault finding procedure to a stored fault.
The fault is declared present after starting the engine and switching on the air
conditioning or running command AC180 Air conditioning relay compressor.
Special notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the condition of the clips of the cold loop/air conditioning relay on the engine fuse and relay board (see the
relay board wiring diagrams for the vehicle concerned).
Replace the clips if necessary.
With the ignition on, check for + 12 V on connection 3FB (or 3FB2) of the cold loop/air conditioning relay,
component code 474.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
Connect the bornier in place of the computer and check the insulation, continuity and the absence of
interference resistance on the following connection:
●38K between the components 120 and 474.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
Check the resistance value of the cold loop/air conditioning relay between connections 3FB (or 3FB2) and 38K
of the relay.
If the resistance is not between: 75  < X < 85  at 25°C, replace the relay.
If the fault is still present, replace the cold loop/air conditioning relay.
DCM1.2_V08_DF489

13B-113
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF532
PRESENT
OR
STOREDALTERNATOR CHARGE SIGNAL
1.DEF: Inconsistency
2.DEF: No signal
NOTESConditions for applying the fault finding procedure to a stored fault:
If the fault is declared present after the engine has been started.
Special notes:
Use bornier Elé. 1681 for any operations on the injection computer connectors.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the condition of the alternator connector, component code 103.
Check the condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the continuity and the absence of interference resistance on the following connection:
●2K between components 120 and 103.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
Check the charging circuit (see Technical Note 6014A (Renault) or Technical Note 9859A (Dacia), Checking
the charging circuit).
Carry out the necessary repairs.
If the fault is still present, contact the Techline.
DCM1.2_V08_DF532

13B-114
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF631
PRESENT
OR
STOREDBRAKE LIGHT SWITCH SIGNAL
1.DEF: No signal
2.DEF: Inconsistency
NOTESSpecial notes:
The fault is declared present when decelerating, when the brake pedal is depressed.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Conditions for applying the fault finding procedure to a stored fault:
Apply the fault finding procedure below if the fault is present or stored.
Check the connection and condition of the brake light switch connector, component code160.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check for + 12 V on connection AP1 or AP10 of the brake light switch supply, component code 160.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●5A between components 120 and 160,
●65A between components 120 and 160,
●AP1 or AP10 between components 160 and 1016 or 260.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If the fault is still present, contact the Techline.
DCM1.2_V08_DF631

13B-116
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF886
PRESENT
OR
STOREDPRESENCE OF WATER IN THE DIESEL FUEL
1.DEF: Open circuit on the line or presence of water in the diesel fuel
NOTESFault finding procedure application conditions:
The fault is declared present after the engine has been started.
Priorities when dealing with a number of faults:
– DF057 Water in diesel fuel detector circuit,
Special note:
If the fault is present, the level 1 warning light comes on or the water present in
diesel fuel warning light comes on (if present on the instrument panel and if
configured in injection).
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check for the presence of water in the diesel filter; if water is present, bleed the diesel filter.
If there is a great amount of water, run the first part of Test 13: Diesel fuel conformity check (Is the fuel cloudy
or does it separate into 2 parts?)
Check the connection and condition of the connector of the water in diesel fuel sensor, component code 414.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check for a voltage between 13V and 14V (with the engine running) and between 11.5 V and 12.5 V (with the
ignition on and engine stopped) on connection 3FB (or 3FB2, or 3FBA) on the connector of the water in diesel
fuel sensor, component code 414.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
DCM1.2_V08_DF886

13B-118
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF1083
PRESENT
OR
STOREDWATER IN DIESEL FUEL WARNING LIGHT CIRCUIT
CC.1: Short circuit to + 12 V
CO.0: Open circuit or short circuit to earth
NOTESSpecial notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Clear the fault and check the correct operation of the warning light with command AC261 Water in fuel warning
light.
Check the connection and condition of the water in diesel fuel warning light connector, component code 414.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3WT between components 120 and 414,
●M (or 3WU) between components 120 and 414,
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A (Renault)
or Technical Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If the fault is still present, replace the instrument panel, component code 247 (see MR 388, (Logan/Sandero), MR
423 (Thalia 2/Symbol 2), MR 451 (Duster) or MR 374 (Kangoo VLL), Mechanical, 83A, Instrument panel,
Instrument panel: Removal - Refitting).
If the fault is still present, contact the Techline.
DCM1.2_V08_DF1083