2013 RENAULT KANGOO injector code

13B-167
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP9
CONTINUED
Check the electrical circuit by running TEST 2 Electrical circuit check.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes
Check the low pressure circuit by running TEST 1 Low pressure circuit check.
Visually check that there are no leakages on the high pressure circuit by running TEST 7 High pressure circuit
sealing check.
Check the injectors by running TEST 3 Injector check.
Check the high pressure system by running TEST 6 High pressure system check.
Check the condition of the computer connections (for bent pins, signs of oxidation, silicone, etc.) and check that
the computer connectors lock correctly.
Contact the Techline if the customer complaint is still present.
A

13B-168
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP10 Engine hesitation
NOTESSpecial note:
Only consult this customer complaint after a complete check using the diagnostic tool
(see System operation, Function: Fuel supply management (advance, flow and
pressure), paragraph: flow capacity function (VLC)).
Check that the fuel tank is filled and that the appropriate fuel is used.
Apply TEST 13 Diesel fuel conformity check.
Check the low pressure circuit by running TEST 1 Low pressure circuit check.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes
Is the engine wiring harness cut or pinched? Carry out the necessary repairs.
Is the compression in order? Carry out the necessary repairs.
Is the valve clearance set correctly? Carry out the necessary repairs.
Check the high pressure pump by running TEST 6 High pressure system check.
YES
NO
NO
YES
NO
YES
A
DCM1.2_V08_ALP10

13B-170
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP11 Loss of power
NOTESSpecial note:
Only address this customer complaint after a complete check with the diagnostic
tool.
See explanation for flow capacity function in system operation.
Is status ET563 Flow capacity function "ACTIVE"?
Using the diagnostic tool, check that the
injector codes (C2I) are correctly
entered on the identification screen. If not,
configure the correct injector codes using
command SC002 Enter injector codesCheck the diesel filter.
Is it close to the replacement mileage?
Replace the diesel filter (see MR 388 (Logan/Sandero),
MR 451 (Duster), MR 423 (Thalia 2/Symbol 2) or MR
374 (Kangoo VLL), Mechanical, 13A, Fuel supply, Fuel
filter: Removal - Refitting).
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Is the engine oil level correct? Top up the oil level.
NOYES
NO
YES
NO
A
YES
DCM1.2_V08_ALP11

13B-172
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP12 Too much power
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
In this case, the control solenoid valve is jammed: it is possible to increase the vacuum but not reduce it
afterwards.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Check that the engine has not sucked up its oil (engine racing).
Check that the turbocharger is working properly.
Run TEST 11 Air line at the turbocharger.
Run TEST 10 Turbocharger solenoid valve check.
Run TEST 12 Turbocharger.
Check the condition of the computer connections (for bent pins, signs of oxidation, silicone, etc.) and check that
the computer connectors lock correctly.
Contact the Techline if the customer complaint is still present.
DCM1.2_V08_ALP12

13B-175
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP 13 Excessive consumption
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check that the fuel tank is correctly filled and that the appropriate fuel is used.
Apply TEST 13 Diesel fuel conformity check.
Check the levels of engine oil and coolant.Replace the fuel temperature sensor (see MR
388 (Logan/Sandero), MR 423 (Thalia 2/Symbol
2), MR 451 (Duster) or MR 374 (Kangoo VLL),
Mechanical, 13B, Diesel injection, Rail pressure
sensor: Removal - Refitting). Is the fuel temperature sensor leaking?
Check the low pressure circuit by running TEST 1 Low pressure circuit check.
Visually check that there are no leakages on the high pressure circuit by running TEST 7 High pressure circuit
sealing check.
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes
YES
NO
A
DCM1.2_V08_ALP13

13B-177
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP14 Overspeed when releasing accelerator or changing gear
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check that there are no obstacles that might impede the accelerator pedal travel (carpet, hard point, etc.).
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes
Visually check the condition of the engine wiring harness.
Is the clutch clearance set correctly?Carry out the necessary
repairs.
Check that the engine has not sucked up its oil (engine racing).
Check that the turbocharger is working properly.
Run TEST 11 Air line at the turbocharger.
Run TEST 10 Turbocharger solenoid valve check.
Run TEST 12 Turbocharger.
Is the turbocharger in order?Carry out the necessary
repairs.
NO
YES
NO
A
YES
DCM1.2_V08_ALP14

13B-179
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP15 Engine dies on pulling away
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Is the clutch clearance set correctly? Carry out the necessary repairs.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Is the catalytic converter clogged or damaged?Replace the catalytic converter (see MR 388
(Logan/Sandero), MR 451 (Duster), MR 423
(Thalia 2/Symbol 2) or MR 374 (Kangoo VLL),
Mechanical, 19B, Exhaust, Catalytic
converter: Removal - Refitting).
Check the low pressure circuit by running TEST 1 Low pressure circuit check.
Visually check the condition of the engine wiring harness.
Check the condition of the computer connections (for bent pins, signs of oxidation, silicone, etc.) and check that
the computer connectors lock correctly.
Contact the Techline if the customer complaint is still present.
NO
YES
YES
NO
DCM1.2_V08_ALP15

13B-181
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP16
CONTINUED
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes
Check the air inlet circuit by running TEST 5 Air inlet circuit check.
Check the low pressure circuit by running TEST 1 Low pressure circuit check.
Check the injectors by running TEST 3 Injector check.
Check the high pressure circuit by running TEST 6 High pressure system check.
Contact the Techline if the customer complaint is still present.
A