2013 RENAULT KANGOO engine speed

13B-25
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF001
PRESENT
OR
STOREDCOOLANT TEMPERATURE SENSOR CIRCUIT
CO.1: Open circuit or short circuit to +12 V
CC.0: Short circuit to earth
NOTESSpecial notes:
If fault DF001 is present, the preheating time is greater than 10 seconds and the
engine fan switches on at low speed (Fan assembly 1). If there is a fault on Fan
assembly 1, then Fan assembly 2 switches on (on vehicles fitted with air conditioning).
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the condition and connection of the coolant temperature sensor connector, component code 244.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connectors, otherwise
replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3C between components 244 and 120,
●3JK between components 244 and 120,
●M (or NH) of component 244,
●42A between components 244 and 247.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Measure the resistance of the coolant temperature sensor between connections 3JK and 3C of component 244.
11.5 k < X < 13,5 k at -10°C,
2140  < X < 2364  at 25°C,
773  < X < 851  at 50°C,
275  < X < 291  at 80°C,
112  < X < 118  at 110°C.
If the value is not correct, replace the coolant temperature sensor (see MR 388 (Logan/Sandero), MR 451
(Duster), MR 423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 19A Cooling, Coolant
temperature sensor: Removal – Refitting).
DCM1.2_V08_DF001
DIESEL INJECTION
Fault finding – Interpretation of faults

13B-29
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF005
PRESENT
OR
STOREDENGINE SPEED SENSOR CIRCUIT1.DEF: Inconsistency
2.DEF: Inconsistency
3.DEF: Too many additional teeth
4.DEF: Teeth missing
5.DEF: Additional teeth
6.DEF: Too many teeth missing
NOTESSpecial notes:
If fault DF005, 1.DEF, 2.DEF, 3.DEF or 6.DEF is present: the engine stops and the
level 2 warning light comes on.
If fault DF005, 4.DEF or 5.DEF is present: engine performance is reduced to 75%, and
no warning light comes on.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Conditions for applying the fault finding procedure to a stored fault:
The fault is present when the starter motor is operating or the engine is running at idle
speed.
Check the connection and condition of the engine speed sensor connector, component code 149.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check that the engine speed sensor is correctly fitted to the engine.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3BL between components 120 and 149,
●3BG between components 120 and 149.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Measure the resistance of the engine speed sensor between connections 3BG and 3BL of component 149.
If the resistance of the engine speed sensor is not between 510  < X < 850  at 20°C, replace the sensor (see
MR 388 (Logan/Sandero) or MR 451 (Duster), MR 423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL),
Mechanical, 13B Diesel injection, Crankshaft position sensor: Removal – Refitting).
Check that the flywheel ring gear is not defective (missing teeth).
If the fault is still present, contact the Techline.
DCM1.2_V08_DF005

13B-31
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF008
PRESENT
OR
STOREDPEDAL POTENTIOMETER CIRCUIT GANG 1CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to +12 V
1.DEF: Inconsistency between pedal gang 1 and gang 2
2.DEF: No signal
3.DEF: Jammed component
NOTESPriority when dealing with a number of faults:
– DF113 Sensor supply voltage.
Special notes:
If fault DF008 is present: the engine speed is maintained above 1000 rpm (normal idle
speed with the brake pedal depressed) and the level 1 warning light comes on
(except 3.DEF).
If faults DF008 and DF009 Pedal potentiometer circuit gang 2 are present: engine
speed fixed at 1300 rpm, level 1 warning light lit.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
1.DEF
3.DEF
NOTESNone.
Disconnect the injection computer connector, component code 120 and the pedal potentiometer connector,
component code 921.
Check the insulation, continuity and the absence of interference resistance of the following connections:
●3LS between components 120 and 921,
●3LW between components 120 and 921.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If the fault is still present, replace the pedal potentiometer (see MR 388 (Logan/Sandero), MR451 (Duster), MR
423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 37A, Mechanical component controls,
Accelerator pedal: Removal – Refitting).
If the fault is still present, contact the Techline.
DCM1.2_V08_DF008

13B-34
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF009
PRESENT
OR
STOREDPEDAL POTENTIOMETER CIRCUIT GANG 2
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to +12 V
NOTESPriority when dealing with a number of faults:
– DF122 Pedal potentiometer gang 2 supply voltage.
Special notes:
If fault DF009 is present: engine speed maintained above 1000 rpm and engine
performance reduced to 75%, the level 1 warning light comes on.
If faults DF009 and DF008 Pedal potentiometer circuit gang 1 are present: engine
speed fixed at 1300 rpm, level 1 warning light lit.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
CO.0
NOTESNone.
Check the connection and condition of the pedal potentiometer connector, component code 921.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check for + 5 V on connection 3LU of the pedal potentiometer, component code 921.
Check for earth on connection 3LV of the pedal potentiometer, component code 921.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Disconnect the computer connector and the connector of the pedal potentiometer, component code 921.
Check the insulation to earth of connection 3LW on the injection computer connector.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
DCM1.2_V08_DF009

13B-42
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF016
PRESENT
OR
STOREDEGR VALVE CONTROL CIRCUITCO.0: Open circuit or short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit.
CO.1: Open circuit or short circuit to + 12 V
CC.0: Short circuit to earth
1.DEF: Detection of overheating
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present with the engine idling.
Special notes:
If fault DF016 is present: unstable engine speed and even stalling.
Starting difficult or even impossible when cold.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
K9K 718, 740, 792, 796 engine (Euro 4):
Check the connection and condition of the exhaust gas recirculation valve connector, component code 1460.
Check the connection and condition of the injection computer, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation and continuity of the following connections:
●3VP between components 1460 and 120,
●3VQ between components 1460 and 120.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A (Renault)
or Technical Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Check for the supply 13 V < X< 14 V (with the engine running), 11.5 V < X < 12.5 V (with the ignition on and
the engine stopped) on connection 3VP of component 1460.
Check for earth on connection 3VQ of component 1460.
DCM1.2_V08_DF016

13B-46
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF018
PRESENT
OR
STOREDLOW SPEED FAN ASSEMBLY CONTROL CIRCUIT
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to + 12 V
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after attempting to start or with the engine running or when
command AC154 Low speed fan assembly is running.
Special notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
CC.1
NOTESNone.
Check the + 12 V after relay feed to the percolation/low speed fan assembly relay mounting, component code 700
on connection 3FB (only for K9K 792, 794, 796 engines) or 3FB2 (only for K9K 790 engines), 796 for Duster or
BP7 (only for K9K 714, 718, 740 engines).
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
Check the condition of the connections and the correct operation of relay 700.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the continuity and the absence of interference resistance on the following connection:
●3JN between components 120 and 700.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
If the fault is still present, contact the Techline.
DCM1.2_V08_DF018

13B-48
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF019
PRESENT
OR
STOREDHIGH SPEED FAN ASSEMBLY CONTROL CIRCUIT
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to + 12 V
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after attempting to start or with the engine running or when
command AC153 High speed fan assembly is running.
Special notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
CC.1
NOTESNone.
Check the + 12 V after relay feed to the fan assembly relay mounting 336 on connection 3FB (only for K9K 792,
794, 796 engines) or 3FB2 (only for K9K 796 engines for Duster) or BP7 (only for K9K 714, 718, 740 engines).
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
Check the condition of the connections and the correct operation of relay 336. Replace it if necessary.
Check the continuity and the absence of interference resistance on the following connection:
●3JP between components 120 and 336.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
If the fault is still present, contact the Techline.
DCM1.2_V08_DF019

13B-54
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF026
PRESENT
OR
STOREDCYLINDER 1 INJECTOR CONTROL CIRCUITCO: Open circuit
CC: Short circuit
1.DEF: At minimum stop
2.DEF: At maximum stop
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present with the engine idling.
Special notes:
When this fault appears, the idle speed is locked at 1000 rpm, there is engine noise,
unsteady engine speed, engine performance reduced to 75% and the level 1 warning
light comes on until the next time the ignition is switched off.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
CO
CC
NOTESNone.
Switch off the ignition and wait 15 seconds.
Check the connection and condition of the injector 1 connector, component code 193.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connectors, otherwise
replace the wiring.
Run command AC005 Cylinder 1 injector.
If injector 1 cannot be heard operating five times in a cycle, connect the wire of the injector of cylinder 2 to the
injector of cylinder 1 and use command AC006 Cylinder 2 injector.
Does this injector actuation cycle work?
Note:
If the wires cannot be swapped, continue the procedure by replying YES to the previous question.
DCM1.2_V08_DF026