2013 RENAULT KANGOO check engine

13B-31
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF008
PRESENT
OR
STOREDPEDAL POTENTIOMETER CIRCUIT GANG 1CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to +12 V
1.DEF: Inconsistency between pedal gang 1 and gang 2
2.DEF: No signal
3.DEF: Jammed component
NOTESPriority when dealing with a number of faults:
– DF113 Sensor supply voltage.
Special notes:
If fault DF008 is present: the engine speed is maintained above 1000 rpm (normal idle
speed with the brake pedal depressed) and the level 1 warning light comes on
(except 3.DEF).
If faults DF008 and DF009 Pedal potentiometer circuit gang 2 are present: engine
speed fixed at 1300 rpm, level 1 warning light lit.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
1.DEF
3.DEF
NOTESNone.
Disconnect the injection computer connector, component code 120 and the pedal potentiometer connector,
component code 921.
Check the insulation, continuity and the absence of interference resistance of the following connections:
●3LS between components 120 and 921,
●3LW between components 120 and 921.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If the fault is still present, replace the pedal potentiometer (see MR 388 (Logan/Sandero), MR451 (Duster), MR
423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 37A, Mechanical component controls,
Accelerator pedal: Removal – Refitting).
If the fault is still present, contact the Techline.
DCM1.2_V08_DF008

13B-34
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF009
PRESENT
OR
STOREDPEDAL POTENTIOMETER CIRCUIT GANG 2
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to +12 V
NOTESPriority when dealing with a number of faults:
– DF122 Pedal potentiometer gang 2 supply voltage.
Special notes:
If fault DF009 is present: engine speed maintained above 1000 rpm and engine
performance reduced to 75%, the level 1 warning light comes on.
If faults DF009 and DF008 Pedal potentiometer circuit gang 1 are present: engine
speed fixed at 1300 rpm, level 1 warning light lit.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
CO.0
NOTESNone.
Check the connection and condition of the pedal potentiometer connector, component code 921.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check for + 5 V on connection 3LU of the pedal potentiometer, component code 921.
Check for earth on connection 3LV of the pedal potentiometer, component code 921.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Disconnect the computer connector and the connector of the pedal potentiometer, component code 921.
Check the insulation to earth of connection 3LW on the injection computer connector.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
DCM1.2_V08_DF009

13B-37
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF010
PRESENT
OR
STOREDEGR POSITION SENSOR CIRCUIT
1.DEF: At minimum limit
2.DEF: At maximum limit
NOTESPriority when dealing with a number of faults:
– DF113 Sensor supply voltage.
Special notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
K9K 714, 718, 740, 792, 796 ENGINES (Euro 4):
Check the connection and condition of the EGR valve connectors, component code 1460.
Check the connection and condition of the computer connectors, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation and continuity of the following connections:
●3GC between components 1460 and 120,
●3EL between components 1460 and 120,
●3JM between components 1460 and 120.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Check for + 5 V on connection 3GC of the EGR valve sensor, component code 1460.
Check for earth on connection 3JM of the EGR valve sensor, component code 1460.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
DCM1.2_V08_DF010

13B-38
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF010
CONTINUED 1
Measure the resistance of the EGR valve, component code 1460:
●with the engine stopped, the EGR valve will be closed (unless there is a fault),
●wait for the ambient temperature to stabilise (approximately 20°C) around the valve,
measure the resistance between connections 3VP and 3VQ of component 1460. The resistance must be between:
0.5  < R < 50 .
If the value is not correct, replace the EGR valve (see MR 388 (Logan/Sandero), MR 451 (Duster), MR 423
(Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 14A, Emission control, Exhaust gas
recirculation solenoid valve: Removal – Refitting).
After replacing the EGR valve, use command RZ002 EGR adaptives to reinitialise the EGR valve offsets.
If the fault is still present, contact the Techline.
K9K 790, 794 ENGINE (euro 3):
Check the connection and condition of the EGR valve connector, component code 1460.
Check the connection and condition of connector B (brown 48-track) of the computer, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation and continuity of the following connections:
●3GC between components 1460 and 120,
●3EL between components 1460 and 120,
●3JM between components 1460 and 120.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Check for + 5 V on connection 3GC of the EGR valve sensor, component code 1460.
Check for earth on connection 3JM of the EGR valve sensor, component code 1460.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.

13B-39
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF010
CONTINUED 2
Check the resistance of the EGR valve, component code 1460:
●with the engine stopped, the EGR valve will be closed (unless there is a fault),
●wait for the ambient temperature to stabilise (approximately 20°C) around the valve,
●measure the resistance between connections 3FB (or 3FB2) and 122B. The resistance must be between
7.54 ●measure the resistance between connections 3GC and 3JM. The resistance must be between 2.4 k < R <
5.6 k (at 20°C),
●measure the resistance between connections 3JM and 3EL. The resistance must be between 800  < R <
3.6 k (at 20°C),
If the value is not correct, replace the EGR valve (see MR388 (Logan/Sandero) or MR451 (Duster), Mechanical,
14A, Emission control, Exhaust gas recirculation solenoid valve: Removal – Refitting). After replacing the
EGR valve, run command RZ002 EGR adaptives to reinitialise the EGR valve offsets.
If the fault is still present, contact the Techline.

13B-41
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF015
PRESENT
OR
STOREDMAIN RELAY CONTROL CIRCUIT
1.DEF: Permanent low level
2.DEF: Permanent high signal
NOTESConditions for applying the fault finding procedure to a stored fault:
Apply the fault finding procedure below if the fault is present or stored.
Special notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the main relay supply fuse in the engine compartment F02 (30 A), F11 (for Kangoo VLL) or F01 (30 A)
AutoFuse for Duster on the engine fuse and relay box, component code 597 or 260 (for Kangoo VLL) (see MR
388 (Logan/Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical,
81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the injection computer connector, component code 120, and of the
computer supply relay, component code 983 on the engine fuse and relay box.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3AA between components 120 and 983,
●3FB (or 3FB2) between components 120 and 983.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Replace the relay if the fault is still present.
DCM1.2_V08_DF015

13B-42
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF016
PRESENT
OR
STOREDEGR VALVE CONTROL CIRCUITCO.0: Open circuit or short circuit to earth
CC.1: Short circuit to + 12 V
CO: Open circuit.
CO.1: Open circuit or short circuit to + 12 V
CC.0: Short circuit to earth
1.DEF: Detection of overheating
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present with the engine idling.
Special notes:
If fault DF016 is present: unstable engine speed and even stalling.
Starting difficult or even impossible when cold.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
K9K 718, 740, 792, 796 engine (Euro 4):
Check the connection and condition of the exhaust gas recirculation valve connector, component code 1460.
Check the connection and condition of the injection computer, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation and continuity of the following connections:
●3VP between components 1460 and 120,
●3VQ between components 1460 and 120.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A (Renault)
or Technical Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
Check for the supply 13 V < X< 14 V (with the engine running), 11.5 V < X < 12.5 V (with the ignition on and
the engine stopped) on connection 3VP of component 1460.
Check for earth on connection 3VQ of component 1460.
DCM1.2_V08_DF016

13B-43
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF016
CONTINUED 1
Measure the resistance of the EGR valve, component code 1460:
●with the engine stopped, the EGR valve will be closed (unless there is a fault),
●wait for the ambient temperature to stabilise (approximately 20°C) around the valve,
measure the resistance between connections 3VP and 3VQ of component 1460. The resistance must be between:
0.5  < R < 50 .
If the value is not correct, replace the EGR valve (see MR 388 (Logan/Sandero), MR 451 (Duster), MR 423
(Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 14A, Emission control, Exhaust gas recirculation
solenoid valve: Removal - Refitting).
After replacing the EGR valve, use command RZ002 EGR adaptives to reinitialise the EGR valve offsets.
If the fault is still present, contact the Techline.
K9K 790, 794 engine (Euro 3):
Check the connection and condition of the exhaust gas recirculation solenoid valve connector, component code
1460.
Check the connection and condition of the injection computer, component code 1260.
If the connector(s) are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation and continuity of the following connections:
●3FB (or 3FB2) between components 1460 and 120,
●122B between components 1460 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check for the supply 13 V < X < 14 V (with the engine running), 11.5 V < X < 12.5 V (with the ignition on and
the engine stopped) on connection 3FB (or 3FB2) of component 1460.
Check for earth on connection122B of component1460.