2013 RENAULT KANGOO wiring

13B-143
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$120.mif
13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
PR058AIR TEMPERATURE
NOTESSpecial notes:
This circuit is not present on vehicles equipped with K9K 790, 794 engines.
Only apply the checks if the parameter is inconsistent.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2 or
Symbol 2.
Check the condition of the air flowmeter connections, component code 799.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A (Renault) or Technical Note
9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace
the wiring.
If necessary, replace the air temperature/pressure sensor (see MR 388 (Logan/Sandero) or MR 451 (Duster),
Mechanical, 12A, Fuel mixture, Air flowmeter: Removal - Refitting).
Measure the resistance between connections 3B and 3DW of the air flowmeter.
If the resistance of the air temperature / pressure sensor is not:
(theoretical values)
41255  < X < 47492  at – 40°C,
14260  < X < 16022  at – 20°C,
5497  < X < 6050  at 0°C,
2353  < X < 2544  at 20°C,
1114  < X < 1186  at 40°C,
569  < X < 597  at 60°C,
310  < X < 322  at 80°C,
180  < X < 185  at 100°C,
replace the air temperature / pressure sensor (see MR388 (Logan/Sandero) or MR451 (Duster), Mechanical,
12A, Fuel mixture, Air flowmeter: Removal - Refitting).
DCM1.2_V08_PR058
DIESEL INJECTION
Fault finding – Interpretation of parameters

13B-144
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$120.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
PR064COOLANT TEMPERATURE
NOTESSpecial notes:
Only apply the checks if the parameter is inconsistent.
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check the condition of the coolant temperature sensor connections, component code 244.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A (Renault) or Technical Note
9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace
the wiring.
If necessary, replace the sensor.
Measure the resistance between connections 3C and 3JK of the coolant temperature sensor, component code
244:
If the resistance of the coolant temperature sensor is not:
(theoretical values)
11.5  < X < 13.5  at – 10°C,
2140  < X < 2364  at 25°C,
773  < X < 851  at 50°C,
275  < X < 291  at 80°C,
112  < X < 118  at 110°C,
Replace the coolant temperature sensor (see MR 388 (Logan/Sandero), MR 451 (Duster), MR 423 (Thalia 2/
Symbol 2) or MR 374 (Kangoo VLL), Mechanical, 19A Cooling, Coolant temperature sensor: Removal –
Refitting).
DCM1.2_V08_PR064

13B-150
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP1 No dialogue with the computer
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
Try to establish dialogue with a computer on another vehicle to check that the diagnostic tool is not faulty. If the
tool is not at fault, and dialogue cannot be established with any other computer on the same vehicle, the cause
could be a faulty computer interfering on the multiplex network. Check the battery voltage and make the necessary
adjustments to obtain a correct voltage (9.5 V < Battery voltage < 17.5 V).
Carry out fault finding on the multiplex network using the diagnostic tool (see88B, Multiplexing).
Check the presence and the condition of the injection fuses in the engine fuse box.
Check the connection of the injection computer connectors, component code 120 and the condition of its
connections.
Check the injection computer earths (quality, oxidation, tightness of earth bolts on the battery terminal).
Check that the supply to the computer is correct:
●NH or N between the earth and component 120.
●AP29 or AP15 between components 1016 or 260 and 120.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A (Renault)
or Technical Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
A
DCM1.2_V08_ALP01
DIESEL INJECTION
Fault finding – Fault Finding Chart

13B-151
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP1
CONTINUED
Ensure that the diagnostic socket, component code 225, has properly power supply:
●+ Before ignition feed on connection BP56 or BP10 of component 225.
●+ After ignition feed on connection AP10 of component 225.
●Earth on connections MAM and NC or MK and NA of component 225.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A (Renault)
or Technical Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If dialogue has still not been established after these checks, contact the techline.
A

13B-153
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP2
CONTINUED 1
Is the timing set correctly? Carry out the necessary repairs.
Visually check the condition of the engine wiring harness.
Does the starter motor operate correctly (minimum engine
speed = 200 rpm)?Carry out the necessary repairs.
Is the compression in order? Carry out the necessary repairs.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen.
If not, configure the correct injector codes using command SC002 Enter injector codes
Is PR038 Rail pressure less than 50 bar under + after
ignition feed?Apply the fault finding procedure for
DF007 Rail pressure sensor
circuit.
A
NO
YES
NO
YES
NO
YES
NO
B
YES

13B-156
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP3
CONTINUED 1
Is the timing set correctly? Carry out the necessary repairs.
Is the compression in order? Carry out the necessary repairs.
Visually check the condition of the engine wiring harness.
Check the electrical circuit by running TEST 2 Electrical circuit check.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes
A
NO
YES
NO
YES
B

13B-158
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP4 Starting difficult with warm engine
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check that the tank has been filled correctly.
Check the air inlet circuit by running TEST 5 Inlet circuit check.
Is the compression in order? Carry out the necessary repairs.
Is the catalytic converter clogged or damaged?Replace the catalytic converter (see
MR 388 (Logan/Sandero), MR 451
(Duster), MR 423 (Thalia 2/Symbol 2) or
MR 374 (Kangoo VLL), Mechanical,
19B, Exhaust, Catalytic converter:
Removal - Refitting).
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes
Visually check the condition of the engine wiring harness.
Check the low pressure circuit by running TEST 1 Low pressure circuit check.
NO
YES
YES
NO
A
DCM1.2_V08_ALP04

13B-160
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
V1 MR-376-X76-13B000$150.mif
DIESEL INJECTION
Fault finding – Fault Finding Chart13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
ALP5 Rough idle (pumping)
NOTESOnly address this customer complaint after a complete check with the diagnostic
tool.
Check that the tank is correctly filled and that the appropriate fuel is used.
Apply test 13 Diesel fuel conformity check.
Check the low pressure circuit by running TEST 1 Low pressure circuit check.
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen. If
not, configure the correct injector codes using command SC002 Enter injector codes
Visually check the condition of the engine wiring harness.
Visually check that there are no leakages on the high pressure circuit by running TEST 7 High pressure circuit
sealing check.
A
DCM1.2_V08_ALP05