2013 RENAULT KANGOO key

82D-29
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-82D000$130.mif
82D
UCH
Vdiag No.: 0F
PR056NUMBER OF KEYS ALLOCATED
NOTESCheck that no fault is present.
This parameter indicates the number of keys allocated to the vehicle.
The maximum number of allocated keys is 4.
In the event of a fault, perform fault finding on the UCH (see87B, Passenger compartment connection unit).
UCH_V0F_PR056
ACCESS - SECURITY
Fault finding – Interpretation of parameters

82D-30V1 MR-376-X76-82D000$140.mif
82D
UCH
Vdiag No.: 0F
Tool command Diagnostic tool name Comments
AC004Central door locking Refer to the interpretation of the command.
AC005Central door unlocking Refer to the interpretation of the command.
AC006Driver's door unlocking Refer to the interpretation of the command.
AC136Remote locking buzzer Refer to the interpretation of the command.
SC003Spare Refer to the interpretation of the command.
SC015Key allocation Refer to the interpretation of the command.
ACCESS - SECURITY
Fault finding – Command summary table

82D-34
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-82D000$150.mif
ACCESS - SECURITY
Fault finding – Interpretation of commands82D
UCH
Vdiag No.: 0F
This key allocation operation enables you to assign keys to the vehicle.
To add one or more keys, replace one or more keys, de-allocate one or more keys (in the event of theft for example).
Before starting this operation, check that there are no components likely to interfere with the electromagnetic field
(for example: CB (Citizen Band), mobile phones, etc.).
SC015ALLOCATE KEY
Equipment required
CLIP
IMPORTANT
It is not possible to allocate more than two blank keys per operation.
If more than two keys must be allocated: program 2 blank keys then repeat the procedure with all the keys.
WARNING
If not all of the keys are available, all the keys will have to be reallocated. Keys not inserted will no longer be
allocated to this vehicle.
WARNING
The only keys which can be submitted are those ordered for the vehicle concerned, or the vehicle's old keys.
UCH_V0F_SC015

82D-35
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-82D000$150.mif
ACCESS - SECURITY
Fault finding – Interpretation of commands82D
UCH
Vdiag No.: 0F
The UCH must not be blank in order to be able to program keys.
With this system it is not possible to replace some components, such as the UCH and the key as these parts are
sold blank and uncoded.
SC015
CONTINUED 1
IMPORTANT
Do not interrupt the procedure when it is in progress.
If it is interrupted, restart the procedure in "not connected mode"; a new programming key will be displayed.
IMPORTANT
When the programming operation is complete, only remove the key once the Remove key message is displayed
on the screen. Otherwise the programming operation fails and the key will be unusable.
WARNING
When the tool issues the programming key, the user has a limited time in which to enter the immobiliser code.
If the time has elapsed, the CLIP tool displays the message: Time elapsed. Restart the procedure.

82D-36
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-82D000$150.mif
ACCESS - SECURITY
Fault finding – Interpretation of commands82D
UCH
Vdiag No.: 0F
Key allocation procedure
– Establish dialogue with the UCH.
– Select the Repair mode menu.
– Select the Programming menu.
– Select line SC015 Allocate key.
The key allocation procedure takes place in two stages:
1. Key insertion stage.
2. Key allocation stage.
1- Key insertion stage
Clip requires that the keys to be allocated are inserted.
Insert ALL the keys to be allocated (old and new blank keys). Any keys not inserted at this stage will be rejected at
the Key allocation stage and the operation will have to be restarted from the beginning.
Once all the keys are inserted, the Clip diagnostic tool displays the programming key in "not connected" mode.
To obtain the immobiliser code, (see Technical Note 5037A, Code delivery procedure).
2- Key allocation stage:
Continue the procedure following the instructions on the Clip diagnostic tool.
Once the keys have been allocated, make sure that all the keys can lock and start the vehicle.
SC015
CONTINUED 2
IMPORTANT
In "not connected" mode, the programming key can only be used for a limited amount of time, as indicated by the
CLIP diagnostic tool. After this time, the programming key and associated immobiliser code are no longer valid.
The operation must be restarted from the beginning.

82D-39
AFTER REPAIRCarry out a complete check with the diagnostic tool.
V1 MR-376-X76-82D000$170.mif
ACCESS - SECURITY
Fault finding – Fault finding chart82D
UCH
Vdiag No.: 0F
ALP 7
CONTINUED 1
Is the immobiliser warning light illuminated
CONTINUOUSLY?Does the warning light flash?
Normally Rapidly
The UCH has not
detected the after
ignition feed.Carry out a test
using the
diagnostic tool and
deal with status
ET185 Key code
received.
See 87B, Passenger compartment
connection unit.Carry out a test using
the diagnostic tool
and deal with status
ET004 + 12 V after
ignition.
A
NO
YES