2013 RENAULT CLIO CUP steering wheel

Downloaded from www.Manualslib.com manuals search engine 98CUP_2013 Release

C-25

B.6.4.8 Resetting the chassis sensors

This procedure allows to reset the following sensor s:
- Front Brake pressure sensor
- Rear brake pressure sensor
- Steering angle sensor
It is necessary to make a reset if one of the follo wing sensor has been changed or if the
brake circuit has been bleeded.
CONDITIONS :


The car must be in the following configuration to a llow the procedure:
- Engine stalled
- Gearbox in Neutral
- Speed = 0 kph
- Brake pedal released
- Steering wheel straight
- Car on a flat surface · Press the “ON” button to power supply the car
· Display the “brake diagnostic” page
· Press the “RESET” button, the following message app ears :

· press again the “RESET” button gain to start the pr ocedure or “PAGE” button
(steering wheel) to cancel it

· Check in the “brake diagnostic” page that the value of :
Front BP = 0 bar
Rear BP = 0 bar
Steering angle = 0 °

This page only reminds
the conditions to
perform the RESET
procedure

Downloaded from www.Manualslib.com manuals search engine 98CUP_2013 Release

C-26

B.6.5 ADJUSTING THE DRIVING POSITION

B.6.5.1 Adjusting the steering wheel

To optimize the driving position, the height and de epness of the steering wheel may be
adjusted by unlocking the steering column lever (1)


NOTE :
After having set the
steering column position,
the adjustment lever
must be removed (1
screw to remove). It is
strictly forbidden to run
with it (FIA regulation)



B.6.5.2 Adjusting the seat

To move the seat forwards or backwards, place the s eat in the required position and then
re-screw the brackets in the appropriate holes (2).

The height and angle of the seat may be adjusted th e same way by altering its
attachment points on the brackets (3).


(2)
(3)

Downloaded from www.Manualslib.com manuals search engine 98CUP_2013 Release

C-35

B.9.2 REPLACEMENT OF MECHANICAL COMPONENTS

The mileage of the below parts must be monitored by the user throughout the vehicle’s
lifetime.
The mileage stated in the table below is the maximu m expected mileage before
replacement, notwithstanding any incidents or accid ents.
Should any component become faulty or its condition deteriorate before reaching the
stated mileage, please contact Renault Sport Techno logies.

NOTE :
This list may not under any circumstances be cons idered to be part of the
manufacturer’s warranty.

Parts Recommanded milage
Front axle
Point E and Point F ball joint 5000 km
Wishbone ball joints 3000 km
Wheel bearing 5000 km
Shock absorbers + Bump stop 5000 km
Support strut 10000 km
Anti-roll ball joint 7000 km
Wheel stud and nut 5000 km
Rear Axle
Point F ball joint 7000 km
Point E ball joint 7000 km
Point A ball joint 7000 km
Wheel bearing 5000 km
Shock absorbers + Bump stop 5000 km
Wheel stud and nut 5000 km
Steering
Power steering module 15000 km
Steering rack 7500 km
Steering rod ball joint (point H) 7000 km
Rack ball joint 7000 km
Transmission
Gearbox 7500 km
Clutch friction 4500 km
Clutch mecanism 4500 km
Slave cylinder bearing 5000 km
Driveshafts 5000 km
Engine
Engine / Turbo / HP pump / WG / pop off 10000 km
Starter / alternator 10000 km
Engine + Gearbox mountings 10000 km
Motorised Throttle 6000 km
Gas Pedal potentiometer 10000 km
Brakes
Front brake disc 1500 km
Front brake caliper 6000 km
Rear brake disc 8000 km
Rear brake calliper 8000 km

NOTE:
Particular attention must be paid to the state of t he fasteners after any work has
been carried out.