2013 RENAULT CLIO CUP reset

Downloaded from www.Manualslib.com manuals search engine 98CUP_2013 Release

C-2


B PRESENTATION

CONTENTS
B
PRESENTATION 2
B.1 IDENTIFICATION 4
B.1.1 ROLL CAGE 4
B.1.2 CHASSIS NUMBER 4
B.1.3 HOLOGRAMS 5
B.1.4 MARKINGS 5
B.2 DIMENSIONS 6
B.3 CAPACITIES 7
B.4 GENERAL CHARACTERISTICS 8
B.5 HANDLING 9
B.5.1 LIFTING 9
B.5.2 TOWING 9
B.6 USING THE CAR 10
B.6.1 FACIA SWITCH PANEL : XAP_SWT98 10
B.6.2 STEERING WHEEL SWITCH PANEL : XAP_STER98 11
B.6.3 DASHBOARD: COSWORTH ICD 01D-032954-RST 12
B.6.3.1 PAGES 12
B.6.3.1.1 DRIVER PAGE 1 : RACE PAGE 12
B.6.3.1.2 DRIVER PAGE 2 : QUALIFICATION PAGE 13
B.6.3.1.3 DRIVER PAGE 3 : CIRCUIT MAP PAGE 14
B.6.3.1.4 DIAGNOTIC PAGE 1 : ENGINE DIAGNOSTIC 14
B.6.3.1.5 DIAGNOSTIC PAGE 2 : GEARBOX DIAGNOSTIC 16
B.6.3.1.6 DIAGNOSTIC PAGE 3 : BRAKE / CHASSIS DIAGNOSTIC 17
B.6.3.1.7 DIAGNOSTIC PAGE 4 : CBNT DIAGNOSTIC (PAGE 1/2 : STATUS) 17
B.6.3.1.8 DIAGNOSTIC PAGE 5 : CBNT DIAGNOSTIC (PAGE 1/2 : STATES) 18
B.6.3.2 CHANGING PAGES 19
B.6.3.3 LEDS / SHIFTLIGHTS 19
B.6.3.4 ALARMS DISPLAYED ON THE DASHBOARD 20
B.6.3.4.1 MAIN ALARMS (CATEGORY A) 20
B.6.3.4.2 SECONDARY ALARMS (CATEGORY B) 21
B.6.3.4.3 ALARMS AND THRESHOLD 21
B.6.4 BASIC PROCEDURES 22
B.6.4.1 POWER-UP 22
B.6.4.2 STARTING 22
B.6.4.3 TURNING OFF THE ENGINE 23
B.6.4.4 SWITCHING OFF THE POWER SUPPLY 23
B.6.4.5 CHANGING GEARS 23
B.6.4.6 PIT LIMITER 23
B.6.4.7 CONTROLLING THE RAIN LIGHT 24
B.6.4.8 RESETTING THE CHASSIS SENSORS 25

Downloaded from www.Manualslib.com manuals search engine 98CUP_2013 Release

C-10

B.6 USING THE CAR


B.6.1 FACIA SWITCH PANEL : XAP_SWT98

1 – Power supply
2 push buttons ON/OFF
2 – Ignition 1 switch ON/OFF
3 – Starter excitation
1 push button
4 – Fuel pump override
1 push button
5 – Rear Rain light 1 switch ON/OFF
6 – Engine Map 1 switch DRY/WET
7 – Reset : 1 push button
8 – Heating : 1 switch ON/OFF
9 – Fire extinguisher
1 push button
1 2
4
3
5 6 7
8 9

Downloaded from www.Manualslib.com manuals search engine 98CUP_2013 Release

C-25

B.6.4.8 Resetting the chassis sensors

This procedure allows to reset the following sensor s:
- Front Brake pressure sensor
- Rear brake pressure sensor
- Steering angle sensor
It is necessary to make a reset if one of the follo wing sensor has been changed or if the
brake circuit has been bleeded.
CONDITIONS :


The car must be in the following configuration to a llow the procedure:
- Engine stalled
- Gearbox in Neutral
- Speed = 0 kph
- Brake pedal released
- Steering wheel straight
- Car on a flat surface · Press the “ON” button to power supply the car
· Display the “brake diagnostic” page
· Press the “RESET” button, the following message app ears :

· press again the “RESET” button gain to start the pr ocedure or “PAGE” button
(steering wheel) to cancel it

· Check in the “brake diagnostic” page that the value of :
Front BP = 0 bar
Rear BP = 0 bar
Steering angle = 0 °

This page only reminds
the conditions to
perform the RESET
procedure