2013 NISSAN X-TRAIL ESP


> (GLW    0RGHO 7$@
5-12
Starting anddriving
especially incold weather.
CAUTION:
Do not leave thevehicle unattended whilethe
engine iswarming up.
GUID-85BD 5A32-4CA0-4 B20-A3F7-7F2F8C6EA 88C
1. Apply theparking brake.
2. Continuously Variable Transmission (CVT)
model:
Move theshift lever tothe ªPº (Park) orthe ªNº
(Neutral) position.
The starter isdesigned tooperate onlywhen
the shift lever isin the proper position.
Manual Transmission (MT)model:
Move theshift lever tothe ªNº (Neutral) position.
The starter isdesigned tonot operate unless
the clutch pedalisfully depressed.
The Intelligent Keymust becarried when
operating theignition switch.
3. Place theignition switchinthe ªONº position.
Depress thebrake pedal(CVTmodel) orthe
clutch pedal(MTmodel) andpush theignition
switch tostart theengine.
For diesel engine models: Wait until theglow
indicator light
goes out.
T o start theengine immediately ,push andrelease
the ignition switchwhiledepressing thebrake
pedal orclutch pedalwiththeignition switchin
any position.
4. Immediately releasetheignition switchwhenthe
engine starts.Ifthe engine starts,butfails torun,
repeat theabove procedures.
If the engine isvery hard tostart inextremely cold
or hot weather, depresstheaccelerator pedaland
hold it.Push theignition switchforupto15
seconds whileholding. Release theaccelerator
pedal whentheengine starts.
CAUTION:
. Assoon asthe engine hasstarted, release
the ignition switchimmediately.
. Donot operate thestarter formore than15
seconds atatime. Ifthe engine doesnot
start, place theignition switchinthe ªOFFº
position andwait 10seconds beforecrank-
ing the engine again.Otherwise, thestarter
could bedamaged.
. Ifitbecomes necessary tostart theengine
with abooster batteryandjumper cables,
the instructions andcautions contained in
the ª6.Incase ofemergencyº sectionshould
be carefully followed.
5. Allow theengine toidle foratleast 30seconds
after starting theengine towarm-up. Driveat
moderate speedsforashort distance first,
especially incold weather.
CAUTION:
Do not leave thevehicle unattended whilethe
engine iswarming up.
6. To stop theengine, movetheshift lever tothe ªPº
(Park) position (CVTmodel) ormove theshift lever
to the ªNº (Neutral) position(MTmodel) ,apply the
parking brakeandplace theignition switchinthe
ªOFFº position.
ST ARTING ENGINE (modelwith
Intelligent Keysystem)
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
T32A1308 27-5DFB93F9 -CDD2-40A4-B4CA-7AD 7192119CB
DRIVING WITHCONTINUOUSL YVARI-
ABLE TRANSMISSION (CVT)
T32A1308 27-F7C5B DAC-B708- 41F7-9A32-F14C17BDCD AE
The Continuously Variable Transmission (CVT)inyour
vehicle iselectronically controlledtoproduce maximum
power andsmooth operation.
The recommended operatingprocedures forthis
transmission areshown onthe following pages.Follow
these procedures formaximum vehicleperformance
and driving enjoyment.
WARNING:
Do not downshift abruptlyonslippery roads.
This maycause aloss ofcontrol.
CAUTION:
. The cold engine idlespeed ishigh, souse
caution whenshifting thetransmission into
a forward orreverse position beforethe
engine haswarmed up.
. Avoid revving upthe engine whilethe
vehicle isstopped. Thiscould cause unex-
pected vehicle movement.
. Never shifttoeither theªPº (Park) orªRº
(Reverse) positionwhilethevehicle ismov-
ing. This could cause serious damage tothe
transmission.
. Start theengine ineither theªPº (Park) or
ªNº (Neutral) position.Theengine willnot
start inany other position. Ifitdoes, have
your vehicle checked byaNISSAN dealer.
. Except inan emergency, donot shift tothe
ªNº (Neutral) positionwhiledriving. Coast-
ing with thetransmission inthe ªNº (Neutral)
position maycause serious damage tothe transmission.
. Shift intotheªPº (Park) position andapply
the parking brakewhenatastandstill for
longer thanashort waiting period.
. Keep theengine atidling speed while
shifting fromtheªNº (Neutral) positionto
any driving position.
. When stopping thevehicle onanuphill
grade, donot hold thevehicle bydepressing
the accelerator pedal.Thefoot brake pedal
should bedepressed inthis situation.
Starting vehicle
T32A1308 27-E0E8CE2C -3F3F-496A-B326-0ED705AD3FCB
1. After starting theengine, fullydepress thefoot
brake pedalbefore moving theshift lever outofthe
ªPº (Park) position.
2. Keep thefoot brake pedaldepressed andmove
the shift lever toadriving position.
3. Release theparking brake,thefoot brake pedal,
and then gradually startthevehicle inmotion.
The CVT isdesigned sothe foot brake pedal
MUST bedepressed beforeshifting fromtheªPº
(Park) position toany driving position whilethe
ignition switchisin the ªONº position.
The shift lever cannot bemoved outofthe ªPº
(Park) position andinto anyofthe other
positions ifthe ignition switchisplaced inthe
ªLOCKº ,ªOFFº orªACCº position.
CAUTION:
. DEPRESS THEFOOTBRAKE PEDAL-Shift-
ing the shift lever toªDº ,ªDsº ,ªR º, ªL ºor
manual shiftmode without depressing the
foot brake pedalcauses thevehicle tomove
slowly whentheengine isrunning. Make sure
thefoot brake pedalisdepressed fully
and thevehicle isstopped beforeshifting
the shift lever.
. MAKE SUREOFTHE SHIFT LEVER POSI-
TION -Make suretheshift lever isin the
desired position. ªDº,ªDsº ,ªL ºand manual
shift mode areused tomove forward and
ªR ºto back up.
. WARM UPTHE ENGINE -Due tothe higher
idle speeds whentheengine iscold, extra
caution mustbeexercised whenshifting the
shift lever intothedriving position immedi-
ately afterstarting theengine.
Shifting
GUID-668 83E50-62D B-4D0A-AD 0D-64E18A8 E9465
JVS0391X
With manual shiftmode (LHDmodel) (Type A)
Starting anddriving
5-13
DRIVING
VEHICLE
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
5-16
Starting anddriving
T ype A:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94A EAE0
JVS0392X
Example
1. Place theignition switchinthe ªOFFº orªLOCKº
position.
2. Apply theparking brake.
3. Remove theshift lockrelease cover(shown inthe
illustration above)usingasuitable tool.
4. Insert themechanical keyand push down theshift
lock release.
5. Press theshift lever button andmove theshift
lever tothe ªNº (Neutral) positionwhileholding
down theshift lockrelease. Replace theremoved
shift lockrelease coveraftertheoperation. T
ype B:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94A EAE0
JVS0466X
1. Place theignition switchinthe ªOFFº orªLOCKº
position.
2. Apply theparking brake.
3. Depress theshift lockrelease button.
4. Press theshift lever button andmove theshift
lever tothe ªNº (Neutral) positionwhileholding
down theshift lockrelease.
Place theignition switchinthe ªONº position to
release thesteering wheellock.
The vehicle maybemoved, bypushing, tothe desired
location.
If the shift lever cannot bemoved outofthe ªPº (Park)
position, haveaNISSAN dealerchecktheCVT system
as soon aspossible.
High fluidtemperature protectionmode
T32A1308 27-808BD 7D2-9BE0-4 70E-A660-24 B385D4FB8A
This transmission hasahigh fluidtemperature protec-
tion mode. Ifthe fluid temperature becomestoohigh
(for example, whenclimbing steepgrades inhigh
temperature withheavy loads),engine powerand,
under someconditions, vehiclespeedwillbede-
creased automatically toreduce thechance of
transmission damage.Vehicle speed canbecontrolled with
theaccelerator pedal,butengine andvehicle
speed maybelimited.
Fail-safe
T32A1308 27-5877C8 5B-EA11-4DD 6-9D52-6992317A74D 5
When thefail-safe operation occurs,theCVT willnot
be shifted tothe selected drivingposition.
If the vehicle isdriven underextreme conditions,
such asexcessive wheelspinning andsubse-
quent hardbraking, thefail-safe systemmaybe
activated. Thiswilloccur evenifall electrical
circuits arefunctioning properly.Inthis case,
turn theignition switchoffand wait for10
seconds. Thenplace theignition switchbackin
the ªONº position. Thevehicle shouldreturnto
its normal operating condition. Ifitdoes not
return toits normal operating condition, havea
NISSAN dealercheckthetransmission and
repair itifnecessary.
WARNING:
When thefail-safe operation occurs,vehicle
speed maybegradually reduced.Thereduced
speed maybelower thanother traffic,which
could increase thechance ofacollision. Be
especially carefulwhendriving. Ifnecessary, pull
to the side ofthe road atasafe place andallow
the transmission toreturn tonormal operation,
or have itrepaired ifnecessary.
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
5-18
Starting anddriving
R9M engine model:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94AEAE0
km/h (MPH)
1st 35
(22)
2nd 63
(39)
3rd 98
(61)
4th 136
(85)
5th &6th Ð
(Ð)
GEAR SHIFTINDICA TOR (ifequipped)
GUID-AE4B 246D-E5F4-49 10-9BC9-04131765976 2
JVS0331X
Gear ShiftIndicator appearsinthe vehicle information
display whenthedriver should shiftintoahigher or
lower gearasindicated bythe upordown arrow.
The useofGear ShiftIndicator willhelp toreduce fuel
consumption.
When theuparrow appears, upshifting isrecom-
mended. Whenthedown arrow appears, downshifting
is recommended.
CAUTION:
Gear ShiftIndicator helpstoreduce fuelcon-
sumption. Itdoes notrecommend theappro-
priate gearshiftforalldriving situations. Ina
certain situations, onlythedriver canselect the correct
gear(forexample, whenovertaking,
driving upasteep gradient ortowing atrailer) .
GUID-EB9 25B64-34B7-44CF-8 DDB-6D26A0E20FE2
The Stop/Start SystemorIdling StopSystem is
designed toprevent unnecessary fuelconsumption,
exhaust emissions, andnoise during ajourney:
. When youstop thevehicle withthebrake pedal
depressed (CVT)orwith theshift lever inªNº
(Neutral) andclutch pedalreleased (MT),the
engine isturned offautomatically .
. When yourelease thebrake pedal(CVT) orpush
the clutch pedal(MT),the engine isautomatically
turned on.
CAUTION:
At the end ofthe journey theengine mustbe
stopped andignition turnedoff.Lock thevehicle
as normal. Turning theignition switchOFFwill
shut down allelectrical systems.Failuretodo
this may result inaflat battery.
NO TE:
For model withStop/Start SystemorIdling Stop
System, usethespecial batterythatisenhanced
in regard tothe charge-discharge capacityand
life performance. Avoidusinganon-special
battery forthe Stop/Start SystemorIdling Stop
System, asthis may cause earlydeterioration of
the battery oramalfunction ofthe Stop/Start
System orIdling StopSystem. Forthebattery, it
is recommended touse Genuine NISSANparts.
For more information, contactaNISSAN dealer.
NO TE:
The Stop/Start SystemorIdling StopSystem
will notactivate underthefollowing conditions:
. when theengine iskept idling without any
driving aftertheengine isturned on.
ST OP/ST ARTSY STEM ORIDLING
ST OP SY STEM (ifequippe d)
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
. when theengine coolant temperature islow.
. when thebattery capacity islow.
. when thebattery temperature islow.
. when thevehicle ismoved.
. when thevacuum inthe brake servode-
creases.
. when theengine hoodisopened withthe
engine running.
. when theengine isturned onwith the
engine hoodopen.
. when thedriver's seatbeltisnot fastened.
. when thedriver's doorisopen.
. when thesteering wheelisoperated (for
CVT model) .
. when theStop/Start orIdling StopSystem
indicator blinksatalow speed.
. when thefan speed control isin any position
other thanªOFFº (0)while theairflow
control isin the front defogger position.
. when thefront defogger switchison.
. when thetemperature insidethevehicle is
too high orlow. (When theairconditioner is
off, theStop/Start SystemorIdling Stop
System willoperate.)
. when thefanspeed ofthe airconditioner is
set tothe maximum speed.
. when theStop/Start orIdling StopOFF
switch isturned on.
. when thepower consumption islarge.
. when thevehicle istraveling ataltitudes
higher than2,000 m(6,562 ft)(for MTmodel) .
. when thevehicle istravelling ataltitudes
higher than1500m (4922ft)(R9M engine in
combination withCVTmodels) . .
For Manual Transmission (MT)models
Ð when theshift lever isin any position
except theªNº(Neutral) position.
Ð when theclutch pedalisdepressed.
Ð when theIntelligent Keyisnot inthe
vehicle.
. For Continuously Variable Transmission
(CVT) models
Ð when theaccelerator pedalisdepressed.
Ð when theshift lever isin the ªRº(Reverse)
position.
Ð when thebrake pedalisnot firmly
depressed.
Ð when stopping thevehicle onsteep
sloping roads.
. when theelectric powersteering warning
light, theAnti-lock BrakingSystem(ABS)
warning light,orthe Vehicle Dynamic Con-
trol (VDC)/Electronic StabilityProgram
(ESP) warning lightilluminates.
NO TE:
The engine willnotrestart evenifthe brake
pedal isreleased (CVT)orclutch pedalis
pressed (MT)while theStop/Start Systemor
Idling StopSystem isactivated underthe
following condition:
. when theshift lever isin the ªPº(Park)
position (CVTmodel) .
. when theengine hoodisopened.
. when thedriver seatbeltisunfastened and
the driver's doorisopened (MTmodel) .
. when thegear shiftlever isnot inthe Neutral
position (MTmodels) . NO
TE:
It may take some timeuntil theStop/Start or
Idling StopSystem activates underthefollowing
conditions:
. when thebattery isdischarged.
. when theoutside temperature islow orhigh.
. when thebattery isreplaced orthe battery
terminal isdisconnected forextended peri-
ods and then reconnected.
NO TE:
When theStop/Start SystemorIdling Stop
indicator illuminates, theengine startsrunning
automatically underatleast oneofthe following
conditions:
. the brake pedalisreleased withtheshift
lever inthe ªDº(Drive) orªNº (Neutral)
position (forCVT model) .
. theshift lever isplaced inthe ªDº(Drive) or
ªRº (Reverse) positionfromtheªNº(Neutral)
or ªPº (Park) position (forCVT model) .
. the driver's seatbeltisunfastened, orthe
driver's doorisopen (forCVT model) .
. the battery voltage becomes low(due to
electrical loadfrom other vehicle systems
like headlights, heaters,etc.,or auxiliary
devices connected tothe 12volt socket
inside thevehicle) .
. the vehicle speedisabove about2km/h (1
MPH) .
. thefront defogger isoperated.
. when thetemperature insidethevehicle is
too high orlow. (When theairconditioner is
off, theStop/Start SystemorIdling Stop
System willoperate.)
Starting anddriving
5-19
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
5-24
Starting anddriving
Ð when towing thevehicle withtherear
tires raised fromtheground.
. Operate the4WD mode switch onlywhen
driving straight. Donot operate the4WD
mode switch whenmaking aturn orbacking
up.
. Donot operate the4WD mode switch with
the front wheel spinning.
. Engine idlingspeed ishigh while warming
up the engine. Beespecially carefulwhen
starting ordriving onslippery surfaces with
the 4WD mode switch setinthe AUT Omode.
4WD WARNING
GUID-237 09BED-21 E1-4D10-B8 89-D097C5F3D412
If any malfunction occursinthe Four-Wheel Drive
(4WD) system whiletheengine isrunning, warning
messages appearinthe vehicle information display
.
JVS0411X
If the ª4WD system faultºwarning
*
1
appears, there
may beamalfunction inthe 4WD system. Reduce
vehicle speedandhave yourvehicle checked bya
NISSAN dealerassoon aspossible.
The ª4WD HighTemp. Stopvehicleº (hightempera-
ture) warning
*
2
may appear whiletrying tofree a
stuck vehicle duetoincreased oiltemperature. The
driving modemaychange toTwo-Wheel Drive(2WD) .
If this warning isdisplayed, stopthevehicle withthe
engine idling,assoon asitis safe todo so. Then ifthe
warning turnsoff,you can continue driving.
The ªTyre size incorrectº warning
*
3
may appear ifthere
isalarge difference betweenthediameters of
front andrear wheels. Pulloffthe road inasafe area,
with theengine idling.Check thatalltire sizes arethe
same, thatthetirepressure iscorrect andthat thetires
are not excessively worn.Change the4WD mode
switch tothe 2WD mode anddonot drive fast.
If any warning message continues tobe displayed,
have yourvehicle checked byaNISSAN dealeras
soon aspossible.
CAUTION:
. Donot operate theengine onafree roller
when anyofthe wheels raised.
. Ifthe ª4WD system faultºwarning appears
while driving, theremaybeamalfunction in
the 4WD system. Reducethevehicle speed
and have yourvehicle checked byaNISSAN
dealer assoon aspossible. Beespecially
careful whendriving.
. The power trainmaybedamaged ifyou
continue drivingwiththeª4WD system faultº
warning on.
4WD MODE INDICATOR LIGHTS
T32A130 827-36969 1F0-AE85-4F0 2-8C65-5AED24075D5A
The 4WD mode indicator lights(
,
) are
located inthe meter.
The 4WD mode indicator lights(
,
) illuminate
when theignition switchisplaced inthe ªONº position.
The indicator lightsturnoffwithin 1second.
The 4WD mode indicator lightswilldisplay themode
selected bythe 4WD mode switch whileengine is
running.
The 4WD LOCK indicator light
illuminates
simultaneously alongwiththe4WD AUTOindicator
light
when selecting theLOCK mode.
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
5-26
Starting anddriving
. Always usetires ofthe same type,size,brand,
construction (bias,bias-belted orradial) ,and
tread pattern onallfour wheels. Installtirechains
on the front wheels whendriving onslippery roads
and drive carefully .
. Besure tocheck thebrakes immediately after
driving inmud orwater. (SeeªBrake systemº (P.5-
57) .)
. Whenever youdrive off-road throughsand,mudor
water asdeep asthe wheel hub,more frequent
maintenance mayberequired. Fordetails, referto
ªMaintenance foroff-road drivingºinaseparate
maintenance booklet.
. Avoid parking yourvehicle onsteep hills.Ifyou get
out ofthe vehicle anditrolls forward, backward or
sideways, youcould beinjured.
TIRES OF4WD MODEL
T32A130 827-AE5C0 353-CEE0-4F0C-8B42-DD14B0 A90107
CAUTION:
. Always usetires ofthe same size,brand,
construction (bias,bias-belted orradial) ,
and tread pattern onallfour wheels. Failure
to do somay result inacircumference
difference betweentiresonthe front and
rear axles which willcause excessive tire
wear andmay damage thetransmission,
transfer caseandrear differential gears.
. Only usespare tiresspecified foreach 4WD
model.
If excessive tirewear isfound, itis recommended that
all four tires bereplaced withtires ofthe same size,
brand, construction andtread pattern. Thetire
pressure andwheel alignment shouldalsobechecked
and corrected asnecessary .Contact aNISSAN
dealer.
Snow tires
T32A1308 27-786C9A7 D-5F2C-4C44-8252-7577B2315AD6
If you install snowtires,theymust alsobethe same
size, brand, construction andtread pattern onallfour
wheels.
Tire inflation pressure
T32A130827-0 2F5E13F-EB84-4678-B8E3-01C847020459
Check thepressures inall tires, including thespare,
with agauge periodically whenataservice station.
Adjust tothe specified pressureifnecessary .Tire
pressures areshown onthe tire placard.
Tire rotation
T32A130 827-BCA9A BF3-4A1A-42 5E-8276-807FAAD0A08E
NISSAN recommends thattires berotated every5,000
km (3,000 miles).Do not include thespare tireinthe
tire rotation.
Tire chain
T32A130 827-61205 7E2-0991-4 824-9088-F4 4BB593B9BC
Tire chains mustbeinstalled onlyonthe front
wheels andnotonthe rear wheels.
Do not drive withtirechains onpaved roadswhich are
clear ofsnow .Driving withchains insuch conditions
can cause damage tothe various mechanisms ofthe
vehicle duetosome overstress.
GUID-282 AEC18-44 35-4758-87 F0-FE282A2B8D35
Except forEurope: Vehicle Dynamic Control
(VDC) system
For Europe: Electronic StabilityProgram (ESP)
system
WARNING:
. The VDC/ESP systemisdesigned tohelp the
driver maintain stabilitybutdoes notpre-
vent accidents duetoabrupt steering opera-
tion athigh speeds orby careless or
dangerous drivingtechniques. Reducevehi-
cle speed andbeespecially carefulwhen
driving andcornering onslippery surfaces
and always drivecarefully.
. Donot modify thevehicle's suspension. If
suspension partssuchasshock absorbers,
struts, springs, stabilizer bars,bushings and
wheels arenot NISSAN recommended for
your vehicle orare extremely deteriorated,
the VDC/ESP systemmaynotoperate
properly. Thiscould adversely affectvehicle
handling performance, andtheVDC/ESP
warning light
may illuminate.
. Ifbrake related partssuchasbrake pads,
rotors andcalipers arenot NISSAN recom-
mended orare extremely deteriorated, the
VDC/ESP systemmaynotoperate properly
and theVDC/ESP warninglight
may
illuminate.
. Ifengine control related partsarenot
NISSAN recommended orare extremely
deteriorated, theVDC/ESP warninglight
may illuminate.
. When driving onextremely inclinedsurfaces
such ashigher banked corners, theVDC/
ESP system maynotoperate properly and
VEHICLE DYNAMIC CONTROL
(VDC)/ELECTR ONICSTABILITY
PROGRAM (ESP)SY STEM
&RQGLWLRQ
([FHSWIRU&KLQD



> (GLW    0RGHO 7$@
the VDC/ESP warninglight
may illumi-
nate. Donot drive onthese typesofroads.
. When driving onanunstable surfacesuchas
a turntable, ferry,elevator orramp, theVDC/
ESP warning light
may illuminate. This
is not amalfunction. Restarttheengine after
driving ontoastable surface.
. Ifwheels ortires other thantheNISSAN
recommended onesareused, theVDC/ESP
system maynotoperate properly andthe
VDC/ESP warninglight
may illuminate.
. The VDC/ESP systemisnot asubstitute for
winter tiresortire chains onasnow covered
road.
The Vehicle Dynamic Control(VDC)/Electronic Stabi-
lity Program (ESP)system usesvarious sensors to
monitor driverinputs andvehicle motion. Undercertain
driving conditions, theVDC/ESP systemhelpsto
perform thefollowing functions.
. Controls brakepressure toreduce wheelslipon
one slipping drivewheel sopower istransferred to
a non slipping drivewheel onthe same axle.
. Controls brakepressure andengine outputto
reduce drivewheel slipbased onvehicle speed
(traction controlfunction) .
. Controls brakepressure atindividual wheelsand
engine outputtohelp thedriver maintain controlof
the vehicle inthe following conditions:
Ð understeer (vehicletendstonot follow the
steered pathdespite increased steeringinput)
Ð oversteer (vehicletendstospin duetocertain
road ordriving conditions) .
The VDC/ESP systemcanhelp thedriver tomaintain
control ofthe vehicle, butitcannot prevent lossof
vehicle control inall driving situations. When
theVDC/ESP systemoperates, theVDC/ESP
warning light
in the meter flashes sonote the
following:
. The road maybeslippery orthe system may
determine someaction isrequired tohelp the
vehicle onthe steered path.
. You may feelapulsation inthe brake pedal and
hear anoise orvibration fromunder thehood. This
is normal andindicates thattheVDC/ESP system
is working properly.
. Adjust yourspeed anddriving tothe road
conditions.
If a malfunction occursinthe system, theVDC/ESP
warning light
illuminates inthe meter. TheVDC/
ESP system automatically turnsoff.
The VDC/ESP OFFswitch isused toturn offthe VDC/
ESP system. TheVDC/ESP offindicator light
illuminates toindicate theVDC/ESP systemisoff.
When theVDC/ESP OFFswitch isused toturn offthe
system, theVDC/ESP systemstilloperates toprevent
one drive wheel fromslipping bytransferring powerto
a non slipping drivewheel. TheVDC/ESP warninglight
flashes ifthis occurs. Allother VDC/ESP
functions areoffand theVDC/ESP warninglight
will not flash. TheVDC/ESP systemisauto-
matically resettoon when theignition switchisplaced
in the ªOFFº position thenback tothe ªONº position.
See ªVehicle Dynamic Control(VDC)warning light/
Electronic StabilityProgram (ESP)warning lightº(P.2-
16) and ªVehicle Dynamic Control(VDC)offindicator
light/Electronic StabilityProgram (ESP)offindicator
lightº (P.2-19) .
The computer hasabuilt-in diagnostic featurethat
tests thesystem eachtimeyoustart theengine and
move thevehicle forward orinreverse ataslow speed.
When theself-test occurs,youmay hear aªclunkº noise
and/or feelapulsation inthe brake pedal. Thisis
normal andisnot anindication ofamalfunction.
VEHICLE DYNAMIC CONTROL (VDC)/
ELECTRONIC STABILITY PROGRAM (ESP)
S YSTEM OFFSWIT CH
GUID-6741A 6E6-5C87-4519-ADE2- B1D05929FA1D
SSD1149
The vehicle shouldbedriven withtheVehicle Dynamic
Control (VDC)/Electronic StabilityProgram (ESP)
system ONformost driving conditions.
When thevehicle isstuck inmud orsnow ,the VDC/
ESP system reduces theengine outputtoreduce
wheel spin.Theengine speedwillbereduced evenif
the accelerator isdepressed tothe floor. Ifmaximum
engine powerisneeded tofree astuck vehicle, turn
the VDC/ESP systemoff.
T o turn offthe VDC/ESP system,pushtheVDC/ESP
OFF switch. TheVDC/ESP offindicator light
will
illuminate.
Push theVDC/ESP OFFswitch againorrestart the
engine toturn ONthesystem.
Starting anddriving
5-27
&RQGLWLRQ
([FHSWIRU&KLQD