2013 NISSAN MURANO ignition

Black plate (188,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-36Pre-driving checks and adjustments
JVP0049X
Opening the soft topGUID-4C7A2A7D-B19A-4092-923C-63EC90103CB4Push the ignition switch to the OFF position and
make sure to carry the Intelligent Key with you.
Make sure that the trunk luggage cover is pulled
out and hung on the hooks. Push the door
handle request switch (driver’s or passenger’s)
*Aand hold it until the soft top is fully open.
Condition:

Black plate (189,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
TROUBLESHOOTING GUIDEGUID-2D51144E-87AE-4042-BCCA-A9F63DED76EDIf the soft top stops halfway during operation or does not operate normally, follow the procedures shown in the following table. If the procedures in the
following table do not solve the symptom, immediately contact a NISSAN dealer for the inspection.
SymptomBeepPossible cause Possible solution
The OPEN side of the soft top operating
switch is pushed, but the soft top does not
operate. Sounds twice
The OPEN side of the soft top operating switch is
pushed while the soft top is fully open, or the
CLOSE side of the soft top operating switch is
pushed while the soft top is fully closed. Push the CLOSE side of the soft top operating
switch when the soft top is fully open. Push the
OPEN side of the soft top operating switch when the
soft top is fully closed.
Sounds twice The selector lever is in the R (Reverse) position. Shift the selector lever to the P (Park) or N (Neutral)
position, and then operate the soft top.
Sounds twice The trunk lid is opened. Fully close the trunk lid.
Does not sound The battery voltage is low. Start the engine again and operate the soft top.
Does not sound The operation stops to protect the system. Wait for approximately 5 minutes.
The soft top stops halfway during opera-
tion. Sounds twice
Objects are trapped in the moving structure of the
soft top. Check that an object is not trapped inside the rear
parcel shelf, inner flap and soft top. After the check,
turn the ignition switch to the OFF position, start the
engine again and then operate the soft top.
Sounds twice The battery voltage is low. Start the engine again and operate the soft top.
When the vehicle is being driven, the beep
sounds. Sounds continu-
ously The soft top is partially opened. Immediately park the vehicle in a safe location and
fully open or fully close the soft top.
Pre-driving checks and adjustments3-37
Condition:

Black plate (190,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-38Pre-driving checks and adjustments
IF THE TOP DOES NOT OPEN OR
CLOSE ELECTRICALLY
GUID-17B75AAD-7BCD-4553-9A36-FB3FA5E49CAFIf you cannot operate the soft top with the
operating switch, first check whether all the
following operating conditions are met.
.Vehicle is stopped
. Ignition switch is ON (Run the engine when
operating the top.)
. The trunk is closed
. The selector lever is in a position other than
the R (Reverse) position
. The luggage cover is pulled out and hooked
so that the roof storage area is separated
from the trunk.
If the top still does not move under the above
conditions or has any system malfunction, see a
NISSAN dealer as soon as possible. When you
must close the top by yourself, in the event of
emergency or when an immediate dealer service
is not available, close the top manually accord-
ing to the procedures shown in this section.
When closing the soft top manually:
. Move the vehicle to a safe place, away from
traffic.
. Two people should perform this procedure,
as some of the top parts are extremely
heavy.
The top cannot be opened manually.
WARNING
. Do not drive with the top partially
opened.
. If the top cannot be operated prop-
erly, see a NISSAN dealer as soon
as possible to have your vehicle
checked.
CAUTION
The storage lid is extremely heavy. The
storage lid should be manually opened
or closed by two people.
1. Open the trunk lid. In the event of a
discharged battery, the secondary trunk
release mechanism should be operated.
(See “Trunk lid (CrossCabriolet models)”
earlier in this section.)
2. Open the top storage lid.JVP0036X
a. Remove the trunk light*1.
b. Remove the lower trim clips
*3and
remove the upper and lower trim pieces
*2.
c. Remove the two luggage cover hooks
*4
on the left and right side of the trunk.
Then disconnect the connector
*5on
the left side luggage cover hook.
d. Remove the clips
*6behind the luggage
cover hooks.
Condition:

Black plate (199,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SPA2443
MANUAL OPERATIONGUID-20C3E099-AD1B-4DFF-97DD-6AF9D7373A42
Manual operationGUID-69ADA9CB-3148-41B8-8BFC-2FD888E82F39Pull the lock lever*1down and adjust the
steering wheel forward or rearward to the
desired position.
Push the lock lever up securely to lock the
steering wheel in place.
Pull the lock lever
*2and adjust the steering
wheel up or down to the desired position.
Release the lock lever to lock the steering wheel
in place.
SPA2444A
ELECTRIC OPERATIONGUID-27257F1D-DB84-47F2-83F2-B6F7CC1D700D
Tilt or telescopic operationGUID-0F8A0E36-72D5-4F58-A543-110128462B2DMove the lever to adjust the steering wheel up or
down, forward or rearward to the desired
position.
Entry/Exit function operation (if so
equipped):
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407The automatic drive positioner system will make
the steering wheel move up automatically when
the driver’s door is opened with the ignition
switch in the LOCK position. This lets the driver
get into and out of the seat more easily.
For more information, see “Automatic drive
positioner” later in this section.
GUID-E95255EA-C17D-4F05-8E11-DD566D7FB686
SIC3451
Pre-driving checks and adjustments3-47
SUN VISORS
Condition:

Black plate (201,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SPA2143
Manual anti-glare typeGUID-F100EFA2-76F3-450F-8CD1-FA039540B2A2The night position*1will reduce glare from the
headlights of vehicles behind you at night.
Use the day position
*2when driving in daylight
hours.
WARNING
Use the night position only when ne-
cessary, because it reduces rear view
clarity.
SPA2422A
Type A
SPA2450
Type B
Automatic anti-glare typeGUID-75561106-D8BE-4E21-A23B-64B84E0A7AC5The inside mirror is designed so that it
automatically changes reflection according to
the intensity of the headlights of the following
vehicle.
The anti-glare system will be automatically
turned on when the ignition switch is pushed
to the ON position.
When the anti-glare system is turned on, the
indicator light
*Awill illuminate and excessive
glare from the headlights of the vehicle behind
you will be reduced.
Type A: Push the
switch*Bto make the
inside rearview mirror operate normally and the
indicator light will turn off. Push the
switch
again to turn the system on.
Type B: Push the “*” switch
*Cto make the
inside rearview mirror operate normally. The
indicator light will turn off. Push the “I” switch
*Dto turn the system on.
Do not allow any object to cover the
sensors
*Eor apply glass cleaner on
them. Doing so will reduce the sensitivity
of the sensor, resulting in improper opera-
tion.
For the compass (if so equipped) operation, see
“Compass” in the “2. Instruments and controls”
section.
Pre-driving checks and adjustments3-49
Condition:

Black plate (202,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-50Pre-driving checks and adjustments
For the HomeLink®Universal Transceiver opera-
tion, see “HomeLink®Universal Transceiver” in
the “2. Instruments and controls” section.
OUTSIDE MIRRORSGUID-EA0119F9-F39F-4DB3-A112-568766B0ECF6
WARNING
Objects viewed in the outside mirror on
the passenger side are closer than they
appear. Be careful when moving to the
right. Using only this mirror could cause
an accident. Use the inside mirror or
glance over your shoulder to properly
judge distances to other objects.
SPA2319
Adjusting outside mirrorsGUID-BDFF896E-E842-4BF3-8D64-FADE035BD4D5The outside mirror control switch is located on
the armrest.
The outside mirror will operate only when the
ignition switch is in the ACC or ON position.
Turn the switch right or left to select the right or
left side mirror
*1, then adjust using the control
switch
*2.
Defrosting outside mirrors (if so
equipped)
GUID-68C28473-B796-47E1-911F-00D0EEF293DBThe outside mirrors will be heated when the rear
window defroster switch is operated.
Condition:

Black plate (203,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SPA1829
Foldable outside mirrorsGUID-820E720A-12E0-455E-87A1-9AB90C7B54F2Fold the outside mirror by pushing it toward the
rear of the vehicle.
SIC2064
VANITY MIRRORGUID-67A0AA3C-5897-4AD3-A960-33D20860995ETo use the front vanity mirror, pull down the sun
visor and pull up the cover.
GUID-851FDA9C-62A3-4F94-9BB3-456D0780664EThe automatic drive positioner system has two
features:
.Entry/exit function (for Hardtop models)
. Memory storage
ENTRY/EXIT FUNCTION (for Hardtop
models)
GUID-B20D2394-0488-4194-B222-ACBB971CCC5CThis system is designed so that the driver’s seat
and steering column will automatically move
when the selector lever is in the P (Park)
position. This allows the driver to get into and
out of the driver’s seat more easily.
The driver’s seat will slide backward and the
steering wheel will move up when the driver’s
door is opened with the ignition switch in the
LOCK position and the Intelligent Key not
inserted in the Intelligent Key port.
The driver’s seat and steering wheel will return
to the previous positions when the ignition
switch is pushed to the ACC position.
The driver’s seat will not return to the previous
positions if the seat or steering adjusting switch
is operated when the seat is at the exit position.
Pre-driving checks and adjustments3-51
AUTOMATIC DRIVE POSITIONER (if
so equipped)
Condition:

Black plate (204,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-52Pre-driving checks and adjustments
Cancel or activate entry/exit functionGUID-58D4463D-3833-4D6F-AB39-9C380DA99AC9The selector lever must be in the P (Park)
position with the ignition switch in the OFF
position.
The entry/exit function can be activated or
canceled by pressing and holding the SET
switch for more than 10 seconds.
The indicator lights on the memory switches (1
and 2) will blink once when the function is
canceled, and the indicator lights will blink twice
when the function is activated. Note that the
indicator lights may illuminate after 5 seconds
while holding the SET switch. This indicates
readiness for linking the Intelligent Key to a
stored memory position. Keep the SET switch
pressed for more than 10 seconds to turn on or
off the entry/exit function.
The entry/exit function can also be activated or
canceled if the “Lift Steering Wheel on Exit” key
or “Slide Driver Seat Back on Exit” key is turned
to ON or OFF in the “Comfort” settings. (See
“Vehicle information and settings” in the “4.
Monitor, heater, air conditioner, audio, phone
and voice recognition systems” section.)
Initialize entry/exit functionGUID-3B7D11F0-51D7-4A5F-B078-9C3A3C24A746If the battery cable is disconnected, or if the fuse
opens, the entry/exit function will not work
though this function was set on before. In such
a case, after connecting the battery or replacing
with a new fuse, open and close the driver’s
door more than two times after the ignition
switch is placed in the LOCK position from the
ON position. The entry/exit function will be
activated.
SPA2756
MEMORY STORAGEGUID-1645D943-6DDE-4A8E-B347-C359AF16FEDFTwo positions for the driver’s seat, steering
column and outside mirrors can be stored in the
automatic drive positioner memory. Follow these
procedures to use the memory system.
1. Move the selector lever to the P (Park)position.
2. Push the ignition switch to the ON position.
3. Adjust the driver’s seat, steering column and outside mirrors to the desired positions by
manually operating each adjusting switch.
For additional information, see “Seats” in the
“1. Safety — Seats, seat belts and supple-
mental restraint system” section and “Tilt/
Condition: