2013 NISSAN MURANO ignition

Black plate (142,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
2-58Instruments and controls
Automatic window lowering (CrossCab-
riolet models)
GUID-68431D2A-45C1-4082-9602-DC8E37328739When the soft top operating switch is pressed,
the power windows will automatically be low-
ered completely. The windows do not rise
automatically after the soft top open/close
operation is completed. Use the power window
switches to raise them.
Automatic adjusting function (Cross-
Cabriolet models)
GUID-2A57D8B8-D2B5-4017-A2B4-5D5758878B3A
CAUTION
When the battery cable is removed from
the battery terminal, do not close either
of the front doors. The automatic win-
dow adjusting function will not work
and the side roof panel may be da-
maged.
The power window has an automatic adjusting
function. When the door is being opened, the
window is automatically lowered slightly to avoid
contact between the window and the top side
rail. When the door is closed, the window is
automatically raised slightly.
While the automatic adjusting function does not
work, the window will be controlled as follows: .
When the door is opened, the window
lowers for approximately 0.39 in (10 mm).
. While the door is open, the window cannot
be raised.
If the windows do not close automaticallyGUID-4DA9302E-1FB0-4884-925F-1A056E33BC0EIf the power window automatic function (closing
only) does not operate properly, perform the
following procedure to initialize the power
window system.
1. Push the ignition switch to the ON position.
2. Close the door and soft top (CrossCabriolet
models) .
3. Open the window completely by operating the power window switch.
4. Pull the power window switch and hold it to close the window, and then hold the switch
more than 3 seconds after the window is
closed completely.
5. Release the power window switch. Operate the window by the automatic function to
confirm the initialization is complete.
6. Perform steps 2 through 5 above for other windows.
If the power window automatic function does
not operate properly after performing the pro-
cedure above, have your vehicle checked by a
NISSAN dealer.
GUID-B46D76D1-C71E-43ED-8E5B-5188E0D125CB
WARNING
. In an accident you could be thrown
from the vehicle through an open
moonroof. Always use seat belts
and child restraints.
. Do not allow anyone to stand up or
extend any portion of their body out
of the moonroof opening while the
vehicle is in motion or while the
moonroof is closing.
CAUTION
.Remove water drops, snow, ice or
sand from the moonroof before
opening.
. Do not place any heavy object on
the moonroof or surrounding area.
. Do not push or pull on the sun-
shade. Doing so can damage the
sunshade.
MOONROOF (if so equipped for
Hardtop models)
Condition:

Black plate (143,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
AUTOMATIC MOONROOF AND SUN-
SHADES
GUID-3349AE79-1AF5-473F-9AB7-69A7957FBC85The moonroof and sunshades only operates
when the ignition switch is in the ON position.
The automatic moonroof and sunshades are
operational for about 45 seconds, even if the
ignition switch is pushed to the OFF position. If
the driver’s door or the passenger’s door is
opened during this period of about 45 seconds,
power to the moonroof and sunshades is
canceled.
SIC3801
Sliding sunshade and moonroofGUID-35ECC1C1-78E5-4B3C-860F-E718E2CD552DWhen the moonroof switch is pushed to the
OPEN position
*1, the front and rear sun-
shades will fully open. When the switch is
pushed again, the moonroof will fully open.
When the moonroof switch is pushed to the
CLOSE position
*2, the moonroof will auto-
matically close. Push the switch again, and the
front and rear sunshades will close.
When the moonroof switch is pushed to the
second detent to the OPEN
*3or CLOSE*4
position, both the sunshade and moonroof will
open or close.
To stop the sunshades or moonroof during the operation, push the moonroof switch to either of
the OPEN
*1, CLOSE*2or UP*5position.
Tilting moonroofGUID-5BCB6B6D-1017-4E94-B105-E837913634C6To tilt up the moonroof, push the moonroof
switch to the UP position
*5.
To tilt down the moonroof, push the switch to the
UP position
*5or push the switch to the
CLOSE position
*2.
When the moonroof is tilted up, push the
moonroof switch to the second detent to the
CLOSE position
*4. The moonroof will tilt down
and the sunshades will close.
Auto reverse functionGUID-07736A6E-057D-4405-B60A-86505A7F3C58
WARNING
There are some small distances imme-
diately before the closed position which
cannot be detected. Make sure that all
passengers have their hands, etc., in-
side the vehicle before closing the
moonroof.
If the control unit detects something caught in
the moonroof and sunshades when they are
closing, the moonroof will be immediately
opened.
Instruments and controls2-59
Condition:

Black plate (144,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
2-60Instruments and controls
The auto reverse function can be activated when
the moonroof and sunshades are closed by
automatic operation when the ignition switch is
in the ON position or for about 45 seconds after
the ignition switch is pushed to the OFF
position.
If the moonroof and sunshades cannot be
closed automatically when the auto reverse
function activates due to a malfunction, push
and hold the switch to the CLOSE position
*2.
Depending on the environment or driving
conditions, the auto reverse function may
be activated if an impact or load similar to
something being caught in the moonroof
occurs.
If the moonroof does not operateGUID-55D929EA-1A05-47B0-9DBB-75466D80DB38If the moonroof does not operate properly,
perform the following procedure to initialize the
moonroof operation system.
1. If the moonroof is open, close it fully by pushing the switch to the CLOSE position
*2.
2. Push and hold the switch to the CLOSE position
*2.
3. Release the moonroof switch after the
moonroof or sunshade moves slightly to
the closed position. 4. Push and hold the switch to the CLOSE
position
*2for 10 seconds.
5. The moonroof and sunshades will fully open and then close.
6. Check if the moonroof switch operates
normally.
If the moonroof does not operate properly after
performing the procedure above, have your
vehicle checked by a NISSAN dealer.
GUID-396974CF-8D5C-4223-9393-BF5087FE27B2
SIC4238
MAP LIGHTSGUID-EACC0B68-0B00-4B4C-B7BA-2C1E9F1879FCPush the button as illustrated to turn the light on
or off.
INTERIOR LIGHTS
Condition:

Black plate (145,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SIC3250
PERSONAL LIGHTS (Hardtop models)GUID-649CAF7C-2CCF-4E76-A1BD-9F34B3E94A95
RearGUID-0958BB58-F974-4165-8A79-D4E6DD15AACDPush the button as illustrated to turn the light on
or off.
SIC4239
INTERIOR LIGHT CONTROL SWITCHGUID-2A6055BA-7B37-4FE4-B397-77EF5A05A796The interior light control switch has three
positions: ON, DOOR and OFF.
ON positionGUID-7462AA90-5FAE-4F84-925A-24F0133E09B3When the switch is in the ON position*1the
map lights and rear personal lights will illumi-
nate.
DOOR positionGUID-2534F567-EC7E-4D89-9E58-CCFFC0DDC2B3When the switch is in the DOOR position*2,
the map lights and rear personal lights will
illuminate under the following conditions:
. ignition switch is switched to the LOCK
position — remain on for about 15 seconds.
. doors are unlocked by pushing the UN-
LOCK button on the Intelligent Key or door
handle request switch with the ignition
switch in the LOCK position
— remain on for about 15 seconds.
. any door is opened and then closed with the
ignition switch in the LOCK position
— remain on for about 15 seconds.
. any door is opened with the ignition switch
in the ACC or ON position
— remain on while the door is opened.
When the door is closed, the lights go
off.
The lights will also turn off after a period of
time when the lights remain illuminated
after the ignition switch has been pushed
to the OFF or LOCK position to prevent the
battery from becoming discharged.
Models with color display:
When the auto interior illumination is set to the
OFF position (see “Vehicle information and
settings” in the “4. Monitor, heater, air condi-
tioner, audio, phone and voice recognition
systems” section) , the lights will illuminate under
the following condition:
. any door is opened with the ignition switch
in any position
Instruments and controls2-61
Condition:

Black plate (147,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
GUID-AC16BAD8-F320-4304-996B-A0D05319728A
SIC2131A
When the switch is in the ON position*1, the
light illuminates while the lift gate is opened.
When the lift gate is closed, the light will turn off.
When the switch is in the OFF position
*2, the
light will turn off.
The lights will turn off after a period of
time when the light remain illuminated to
prevent the battery from becoming dis-
charged.
GUID-F7665349-183E-4013-AA39-F31226267085The light illuminates when the trunk lid is
opened. When the trunk lid is closed, the light
will turn off.
The light will also turn off after a period of
time when the light remains illuminated
after the ignition switch has been pushed
to the OFF or LOCK position to prevent the
battery from becoming discharged.GUID-55E56F2F-00B7-4A2E-969B-A4422F852328The HomeLink®Universal Transceiver provides a
convenient way to consolidate the functions of
up to three individual hand-held transmitters into
one built-in device.
HomeLink
®Universal Transceiver:
. Will operate most Radio Frequency (RF)
devices such as garage doors, gates, home
and office lighting, entry door locks and
security systems.
. Is powered by your vehicle’s battery. No
separate batteries are required. If the
vehicle’s battery is discharged or is dis-
connected, HomeLink
®will retain all pro-
gramming.
When the HomeLink
®Universal Transcei-
ver is programmed, retain the original
transmitter for future programming proce-
dures (Example: new vehicle purchases) .
Upon sale of the vehicle, the programmed
HomeLink
®Universal Transceiver buttons
should be erased for security purposes.
For additional information, refer to “Pro-
gramming HomeLink
®” later in this sec-
tion.
Instruments and controls2-63
CARGO LIGHTS (Hardtop models) TRUNK LIGHT (CrossCabriolet
models)HomeLink®UNIVERSAL
TRANSCEIVER (if so equipped)
Condition:

Black plate (159,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
SPA2300
LOCKING WITH POWER DOOR LOCK
SWITCH
GUID-DB03598A-E334-478D-9F87-2864156F8581Operating the power door lock switch will lock
or unlock all the doors. The switches are located
on the driver’s and front passenger’s door
armrests.
To lock the doors, push the power door lock
switch to the lock position
*1with the driver’s
or front passenger’s door open, then close the
door.
When locking the door this way, be certain
not to leave the Intelligent Key inside the
vehicle.
To unlock the doors, push the power door lock switch to the unlock position
*2.
Lockout protectionGUID-BB47EDF9-3384-43BF-9799-EA35B33C1506When the power door lock switch (driver or front
passenger) is moved to the lock position with
the Intelligent Key in the port and any door open,
all doors will lock and unlock automatically. With
the Intelligent Key left in the vehicle (not in the
Intelligent Key port) and any door open, all doors
will unlock automatically and a chime will sound
after the door is closed.
These functions help to prevent the Intelligent
Key from being accidentally locked inside the
vehicle.
AUTOMATIC DOOR LOCKSGUID-FC92C800-B665-49FF-9CDE-4A1CBC7A147B.
All doors will be locked automatically when
the vehicle speed reaches 15 MPH (24
km/h).
. All doors will be unlocked automatically
when the ignition switch is placed in the
OFF position.
The automatic unlock function can be
deactivated or activated. To deactivate or
activate the automatic door unlock system,
perform the following procedure:
1. Close all doors.
2. Place the ignition switch in the ON position. 3. Within 20 seconds of performing Step 2,
push and hold the power door lock switch to
the
position (UNLOCK) for more than 5
seconds.
4. When activated, the hazard indicator will flash twice. When deactivated, the hazard
indicator will flash once.
5. The ignition switch must be placed in the OFF and ON position again between each
setting change.
When the automatic door unlock system is
deactivated, the doors do not unlock when the
ignition switch is placed in the OFF position. To
unlock the door manually, use the inside lock
knob or the power door lock switch (driver’s or
front passenger’s side).
Pre-driving checks and adjustments3-7
Condition:

Black plate (161,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
computer.
. When the vehicle is parked near a parking
meter.
In such cases, correct the operating conditions
before using the Intelligent Key function or use
the mechanical key.
Although the life of the battery varies depending
on the operating conditions, the battery’s life is
approximately 2 years. If the battery is dis-
charged, replace it with a new one.
When the Intelligent Key battery is almost
discharged, insert the Intelligent Key into the
Intelligent Key port to start the engine. Replace
the discharged battery with a new one as soon
as possible. For more details, see “Push-button
ignition switch” in the “5. Starting and driving”
section.
Since the Intelligent Key is continuously receiv-
ing radio waves, if the key is left near equipment
which transmits strong radio waves, such as
signals from a TV and personal computer, the
battery life may become shorter.
For information regarding replacement of a
battery, see “Intelligent Key battery replacement”
in the “8. Maintenance and do-it-yourself”
section.
As many as 4 Intelligent Keys can be registered
and used with one vehicle. For information about
the purchase and use of additional Intelligent Keys, contact a NISSAN dealer.
CAUTION
.
Do not allow the Intelligent Key,
which contains electrical compo-
nents, to come into contact with
water or salt water. This could affect
the system function.
. Do not drop the Intelligent Key.
. Do not strike the Intelligent Key
sharply against another object.
. Do not change or modify the Intel-
ligent Key.
. Wetting may damage the Intelligent
Key. If the Intelligent Key gets wet,
immediately wipe until it is comple-
tely dry.
. If the outside temperature is below
148F (−108C) , the battery of the
Intelligent Key may not function
properly.
. Do not place the Intelligent Key for
an extended period in an area where
temperatures exceed 1408F (608C) .
. Do not attach the Intelligent Key
with a key holder that contains a
magnet. .
Do not place the Intelligent Key near
equipment that produces a mag-
netic field, such as a TV, audio
equipment, personal computer or
cellular phone.
If an Intelligent Key is lost or stolen, NISSAN
recommends erasing the ID code of that
Intelligent Key from the vehicle. This may prevent
the unauthorized use of the Intelligent Key to
operate the vehicle. For information regarding
the erasing procedure, contact a NISSAN deal-
er.
The Intelligent Key function can be disabled. For
information about disabling the Intelligent Key
function, contact a NISSAN dealer.
Pre-driving checks and adjustments3-9
Condition:

Black plate (164,1)
[ Edit: 2012/ 7/ 31 Model: Z51-D ]
3-12Pre-driving checks and adjustments
When you carry the Intelligent Key with you, you
can lock or unlock all doors by pushing the door
handle request switch
*A(driver’s or front
passenger’s) or the lift gate request switch
*B
within the range of operation.
When you lock or unlock the doors or the lift
gate/trunk lid, the hazard indicator will flash and
the horn (or the outside chime) will sound as a
confirmation. For details, see “Setting hazard
indicator and horn mode” later in this section.
Locking doorsGUID-131EB795-ADF4-4035-8A9F-3856D80189ED1. Move the selector lever to the P (Park) position, push the ignition switch to the OFF
position and make sure you carry the
Intelligent Key with you.*1
2. Close all the doors and the lift gate.*2
3. Push the door handle request switch
*Aor
lift gate request switch
*Bwhile carrying
the Intelligent Key with you.*3
4. All the doors and the lift gate will lock.
5. The hazard indicator flashes twice and the outside chime sounds twice.
*1: Doors will lock with the Intelligent Key while the
ignition switch is in the ACC or ON position.
*2: Doors will not lock by pushing the door handle request switch while any door (including the lift
gate) is open.
*3: Doors will not lock by pushing the door handle request switch with the Intelligent Key inside the
vehicle.
However, when an Intelligent Key is inside the
vehicle, doors can be locked with another
registered Intelligent Key.
CAUTION
.
After locking the doors using the
request switch, make sure that the
doors have been securely locked by
operating the door handles.
. When locking the doors using the
request switch, make sure to have
the Intelligent Key in your posses-
sion before operating the request
switch to prevent the Intelligent Key
from being left in the vehicle.
. The request switch is operational
only when the Intelligent Key has
been detected by the Intelligent Key
system.
Lockout protection:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407To prevent the Intelligent Key from being
accidentally locked in the vehicle, lockout
protection is equipped with the Intelligent Key
system.
When the driver’s side door is open, the doors are locked, and then the Intelligent Key is put
inside the vehicle and all the doors are closed;
the lock will automatically unlock and the door
buzzer sounds.
NOTE:
The doors may not lock when the Intelli-
gent Key is in the same hand that is
operating the request switch to lock the
door. Put the intelligent key in a purse,
pocket or your other hand.
CAUTION
The lockout protection may not function
under the following conditions:
.
When the Intelligent Key is placed
on top of the instrument panel.
. When the Intelligent Key is placed
inside the glove box or a storage
bin.
. When the Intelligent Key is placed
inside the door pockets.
. When the Intelligent Key is placed
on or under the spare tire area.
. When the Intelligent Key is placed
on the outer side of trunk area.
Condition: