2013 MITSUBISHI OUTLANDER SPORT warning
[x] Cancel search: warningPage 217 of 602
3-120 Features and controls
3
NOTETire inflation pressures vary with the ambient tempera-
ture. If the vehicle is subjected to large variations in ambi-
ent temperature, the tire inflation pressures may be under-
inflated (causing the warning light/display come on) when
the ambient temperature is relatively low. If the warning
light/display comes on, adjust the tire inflation pressure.Whenever the tires and wheels are replaced with
new ones
N00532900153
If new wheels with new tire inflation pressure sensors are
installed, their ID codes must be programmed into the tire pres-
sure monitoring system. Have tire and wheel replacement per-
formed by an authorized Mitsubishi Motors dealer to avoid the
risk of damaging the tire inflation pressure sensors. If the
wheel replacement is not done by an authorized Mitsubishi
Motors dealer, it is not covered by your warranty.
General information
N00533000223
Your tire pressure monitoring system operates on a radio fre-
quency subject to Federal Communications Commission
(FCC) Rules (For vehicles sold in U.S.A.) and Industry Canada
Rules (For vehicles sold in Canada). This device complies with
Part 15 of the FCC Rules and RSS-Gen of the Industry Canada
Rules.
Operation is subject to the following two conditions.
This device may not cause harmful interference.
This device must accept any interference received, includ-
ing interference that may cause undesired operation.
CAUTION
!The use of non-genuine wheels will prevent the
proper fit of the tire inflation pressure sensors,
resulting air leakage or damage of the sensors.
CAUTION
! Changes or modifications not expressly approved by
the manufacturer for compliance could void the
user’s authority to operate the equipment.
BK0150700US.book 120 ページ ２０１２年３月２２日 木曜日 午後６時４６分
Page 218 of 602
Features and controls3-121
3
Rear-view camera
(if so equipped)
N00546200128
When the gearshift lever or the selector lever is in the “R” posi-
tion with the ignition switch or the operation mode is in ON,
the rear-view image will be displayed on the screen of the
Mitsubishi Multi-Communication System in the center panel or
on the left portion of the inside rearview mirror.
When the gearshift lever or the selector lever is shifted out of
the “R” position, the rear-view image will go off.
Location of rear-view cameraThe rear-view camera (A) is in the liftgate, at the left side of
the liftgate handle.
WARNING
!
Never rely solely on the rear-view camera to clear
the area behind your vehicle. Always check visually
behind and all around your vehicle for persons, ani-
mals, obstructions or other vehicles. Failure to do so
can result in vehicle damage, serious injury or
death.The rear-view camera is an aid system for backing
up, but it is not a substitute for your visual confir-
mation.The view on the screen is limited, and objects out-
side the view, such as under the bumper or around
either corner of the bumper end, cannot be seen on
the screen.
CAUTION
! If the camera lens gets dirty, a clear image cannot be
obtained. As necessary, rinse the lens with clean
water and gently wipe with a clean, soft cloth.To avoid damaging the camera;
• Do not rub the cover excessively or polish it by
using an abrasive compound.
• Do not disassemble the camera.
• Do not splash hot water directly on the lens.
• Do not spray the camera and its surroundings with high-pressure water.
• Make sure that the liftgate is securely closed when
backing up.
BK0150700US.book 121 ページ ２０１２年３月２２日 木曜日 午後６時４６分
Page 221 of 602
3-124 Features and controls
3
NOTEMirror image is displayed on the screen.
Monitor brightness is adjusted automatically by sensors.
It is possible to change the display language of the screen.
For details, please refer to the separated owner’s manual
for “Mitsubishi Multi-Communication System” or
“Change language or turn off the inside rearview mirror
screen: To change the language of warning text (3)” on
page 3-124.
Under certain circumstances, it may become difficult to
see an image on the screen, even when the system is func-
tioning correctly.
• In a dark area, such as at night.
• When water drops or condensation are on the lens.
• When sun light or headlights shine directly into the lens. Change language or turn off the inside rearview
mirror screen
N00568900053
It is possible to turn off the screen of the inside rearview mirror
and change the language of the warning messages on the
screen.
To temporarily set the non-display modeIf you press the switch (1) while the image appears on the
screen, it goes off temporarily.
To return to display mode, press the switch again or perform
the following operation.
[Except for vehicles equipped with the Free-hand Advanced
Security Transmitter (F.A.S.T.-key)]
Turn the ignition switch to the “ON” position after turning to
“OFF” or “ACC” position.
[For vehicles equipped with the Free-hand Advanced Security
Transmitter (F.A.S.T.-key)]
Put the operation mode in ON after putting the operation mode
in OFF.
BK0150700US.book 124 ページ ２０１２年３月２２日 木曜日 午後６時４６分
Page 222 of 602
Features and controls3-125
3
To permanently set the non-display mode1. Turn the ignition switch to the “ON” position or put theoperation mode in ON.
2. Put the gearshift lever or the selector lever in the “R” posi- tion.
3. Press and hold down the switch (1) (for about 15 sec- onds).
While you keep the switch pressed, the orange indicator
(2) comes on. When the image goes off, the non-display
mode setting is completed.
To change the language of warning text (3)1. Turn the ignition switch to the “ON” position or put theoperation mode in ON.
2. Put the gearshift lever or the selector lever in the “R” posi- tion.
3. Press and hold down the switch (1) to enter language selection mode (for 6 to 11 seconds).
In this mode, the image appears and the green indicator
(2) comes on.
4. Press the switch until the desired language appears on the display.
Each time you press the switch, the language will change
to the next one. When the warning text flashes, setting is
completed.
CAUTION
! For safety reasons, do not perform the following
operations with the engine running.
CAUTION
! For safety reasons, do not perform the following
operations with the engine running.
BK0150700US.book 125 ページ ２０１２年３月２２日 木曜日 午後６時４６分
Page 226 of 602
Features and controls3-129
3
Multi-information display
N00555000265
The multi-information display displays warnings, the odometer, trip odometer, service reminder, engine coolant temperature, fue
l
remaining, outside temperature, selector lever position, all-wheel drive operation status, average and momentary fuel consumpti on,
driving range, average speed, instrument brightness, etc.
It is also possible to change elements such as the language and units used on the multi-information display.
With ignition switch or
operation mode is in OFF With ignition switch or operation
mode is in ON (CVT)
Type 1 Type 2 With ignition switch or operation
mode is in ON (Manual transaxle)
Type 1 Type 2 Type 1 Type 2
1- Warning display screen (With ignition switch or opera-
tion mode in OFF) → P.3-131
2- Information screen (With ignition switch or operation mode in OFF) → P.3-131
Interrupt display screen (With ignition switch or operation
mode in OFF) → P.3-134
3- Door ajar warning display screen (With ignition switch or operation mode in OFF) → P.3-135
4- Drive mode indicator display screen (if so equipped)
→ P.3-137
5- Warning display screen (With ignition switch or opera-
tion mode in ON) → P.3-137
6- Active stability control (ASC) OFF display screen (if so equipped) → P.3-137
7- Information screen (With ignition switch or operation mode in ON) → P.3-138
Interrupt display screen (With ignition switch or operation
mode in ON) → P.3-142
8- Selector lever position display screen (if so equipped) → P.3-143
9- Outside temperature display screen → P.3-143
BK0150700US.book 129 ページ ２０１２年３月２２日 木曜日 午後６時４６分
Page 227 of 602
3-130 Features and controls
3
NOTEThe fuel units, temperature units, display language, and
other settings can be changed.
Refer to “Changing the function settings (With ignition
switch or operation mode in ON)” on page 3-148.
The display screen is different depending on whether the
ignition switch or the operation mode in OFF or ON.
Refer to “Information screen (With ignition switch or
operation mode in OFF)” on page 3-131.
Refer to “Warning display list (With ignition switch or
operation mode in OFF)” on page 3-164.
Refer to “Information screen (With ignition switch turned
from the “OFF” position to the “ON” position or opera-
tion mode changed from OFF to ON)” on page 3-136.
Refer to “Information screen (With ignition switch or
operation mode in ON)” on page 3-138.
Refer to “Warning display list (With ignition switch or
operation mode in ON)” on page 3-167.
10- Fuel remaining display screen → P.3-144
11- Engine coolant temperature display (if so equipped)
→ P.3-138
12- ECO mode indicator (if so equipped) → P.3-144
13- Gearshift indicator display screen (if so equipped)
→ P.3-71BK0150700US.book 130 ページ ２０１２年３月２２日 木曜日 午後６時４６分
Page 228 of 602
Features and controls3-131
3
Multi-information meter switch
N00555100149
The multi-information meter switch is a button marked
“INFO” on the left side of the dash.
Each time the multi-information meter switch is operated, a
sound is emitted and the multi-information display changes
between information such as warnings, Odometer (Type1), trip
odometer, service reminder, engine coolant temperature (Type
1), average and momentary fuel consumption, driving range,
and average speed.
It is also possible to change elements such as the language and
units used on the multi-information display by operating the
multi-information meter switch.
Warning display screen (With ignition switch
or operation mode in OFF)
N00555200179
If you press the multi-information meter switch and return
from the warning display screen to the previous screen, the
warning is displayed.
Refer to “Returning to the display screen from before the warn-
ing display” on page 3-134.
This mark is also displayed if there is another warning other
than the one displayed. When the cause of the warning display
is eliminated, the warning goes out automatically.NOTE When the warning is displayed, the warning display
screen can be redisplayed on the information screen.
Refer to “Information screen (With ignition switch or
operation mode in OFF)” on page 3-131.
Refer to “Information screen (With ignition switch or
operation mode in ON)” on page 3-138.Information screen (With ignition switch or oper-
ation mode in OFF)
N00555300167
Each time you lightly press the multi-information meter
switch, the display screen switches in the following order.
BK0150700US.book 131 ページ ２０１２年３月２２日 木曜日 午後６時４６分
Page 229 of 602
3-132 Features and controls
3
Odometer/Trip odometer
N00555400113
Each time you lightly press the multi-information meter
switch, the display screen switches.
Odometer/trip odometer → Odometer/trip odometer →
Service reminder → Redisplay of a warning display screen →
Odometer/trip odometer .
Odometer
Shows the total distance traveled.
Trip odometer
Shows the distance traveled between two points.
To reset the trip odometer
To return the display to 0, hold down the multi-information
meter switch for about 2 seconds or more. Only the currently
displayed value will be reset.
Example
If trip odometer is displayed, only trip odometer will
be reset.
When there is no
warning display
When there is a
warning display
Type 1
Type 2
When there is no
warning display
When there is a
warning display
1-Odometer (Type1)/Trip odometer
2- Odometer (Type1)/Trip odometer
3- Service reminder
4- Redisplay of a warning display screen
Usage examples for trip odometer , trip odometer It is possible to measure two currently traveled distances,
from home using trip odometer and from a particular
point on the way using trip odometer .
BK0150700US.book 132 ページ ２０１２年３月２２日 木曜日 午後６時４６分