2013 MERCEDES-BENZ SPRINTER run flat

Engine speed setting (working
mode)
............................................ 168
Irregularr unning............................ 137
Jump-starting ................................. 267
Operating safety .............................. 25
Starting .......................................... 134
Starting problems ..........................137
Switching off .................................. 146
Tow-starting (vehicle) ..................... 271
Engine, jump-starting .......................267
Engine electronics Notes ............................................. 314
Problem (malfunction) ...................137
Engine oil
Adding ........................................... 244
Additives ........................................ 322
Checking the oil level (on-board
computer) ...................................... 242
Checking the oil level using the
dipstick .......................................... 243
Display message ............................ 206
Filling capacity ............................... 323
Information about oil
consumption .................................. 323
Mixing ............................................ 322
Notes about oil grades ................... 321
Oil change ...................................... 322
Oil leve l(note) ............................... 242
Viscosity ........................................ 321
Warning lamp ................................. 214
Engine spee dsetting (working
mode) ................................................. 167
Equipment/conversions .....................27
ESP ®
(Electronic Stability
Program) Display message ............................ 200
Function/notes ................................ 57
Indicator lamp ................................ 213
Warning lamp ................................. 210
Exhaus tcheck ................................... 148
Exhaust gas aftertreatment ...............27
DEF leve lindicato r......................... 178
DEF reducing agent .................27, 320
Diesel Exhaus tFluid (DEF) .............320
Display messages (vehicles
without steering wheel buttons) ....195
Display messages (vehicles with
steering wheel buttons) .................204Indicator lamp ................................ 213
Malfunction ...................................
.204
Refilling DEF .................................. 143
Exterior lighting
Daytime running lamp mode
(vehicles without steering wheel
buttons) ......................................... 179
Daytime running lamp mode
(vehicles with steering wheel
buttons) ......................................... 187
see Lights
Exterior mirrors
Adjusting ......................................... 86
Important safety notes ....................86
Eyeglasses compartment .................223 F
FAME fuel Bio-diesel ....................................... 317
Fire extinguisher ............................... 266
First-aid kit ......................................... 266
Flat tire Changing a wheel/mounting the
spare wheel ................................... 303
General notes ................................ 295
Preparing the vehicle .....................295
Using tire sealant ........................... 295
Fog lamps
Switching on/off .............................. 91
Folding seat ......................................... 82
Folding table ...................................... 225
Frequencies Mobile phone ................................. 314
Two-way radio ................................ 314
Front fog lamps
Changing the bulbs ..........................98
Switching on/off .............................. 91
Fron tinterior light
Changing bulbs .............................. 102
Fron twindshield
see Windshield
Fuel
Additives (diesel) ........................... 318
Bio-diesel (FAME fuel ).................... 317
Consumption information ..............319
Consumption statistics ..................19010
Index

Air bags
Important safety notes G
WARNING
To reduce the ris kofinjury when the front air
bags inflate, it is very important for the driver
and co-driver to always be in a properly seated
positio nand to wear thei rrespective seat
belt.
For maximum protection in the event of a
collision always be in normal seated position
with your back against the seat backrest.
Fasten your seat belt and make sure it is
properly positioned on your body.
Since the air bag inflates with considerable
speed and force, a proper seating position
and correct positioning of the hands on the
steering wheel will help to keep you at a safe
distance from the air bag. Occupants who are
not wearing their seat belt, are not seated
properly or are too close to the air bag can be
seriously injured or killed by an air bag as it
inflates with great force instantaneously:
R Sit with the seat belt properly fastened in a
position that is as upright as possible with
your back against the seat backrest.
R Move the driver's seat as far back as
possible, still permitting proper operation
of vehicle controls. The distance from the
center of the driver's chest to the center of
the air bag cover on the steering wheel
must be at least 10 inches (25 cm) or more.
You should be able to accomplish this by
adjusting the seat and steering wheel. If
you have any difficulties, please contact a
qualified specialist workshop.
R Do not lean your head or chest close to the
steering wheel or instrument panel.
R Keep hands on the outside of the steering
wheel rim. Placing hands and arms inside
the rim can increase the risk and potential
severity of hand/arm injury when the driver
front air bag inflates. R
Move the co-driver's seat as far as possible
away from the instrument panel when the
seat is occupied.
R Occupants, especially children, should
never place their bodies or lean their heads
in the area of the door where the side
impact air bag inflates .This could result in
serious injuries or death should the side
impact air bag be deployed. Always sit as
upright as possible, wear the seat belt
properly and use an appropriately sized
infant restraint, toddler restraint, or
booster seat recommended for the size and
weight of the child.
R Children twelve years old and under must
never travel on the co-driver's seat. They
will otherwise be struck by the co-driver's
front air bag when it inflates in a crash. This
could result in serious or fatal injury.
Failure to follow these instructions can result
in severe injuries to you or other occupants.
If you sell your vehicle, it is important that you
make the buyer aware of this safety
information. Be sure to give the buyer this
Operator's Manual. G
WARNING
The air bag parts are hot after the airbag has
been deployed. There is a risk of injury.
Do not touch the air bag parts. Have the
deployed air bags replaced at a qualified
specialist workshop as soon as possible.
i If the vehicle is still in running condition,
have it towed to a qualified specialist
workshop. G
WARNING
If you modify the air bag covers or affix objects
such as stickers to them, the air bags may not
function correctly. There is an increased risk
of injury.
Never modify the air bag covers or affix
objects to them. 44
Occupant safetySafety

Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle covers
a distance of 44 feet (approximatel
y14 m)
every second. G
WARNING
If you switch off the ignition while driving,
safety-relevant functions are only available
with limitations, or not at all. This could affect,
for example, the power steering and the brake
boosting effect. You will require considerably
more effort to steer and brake .There is a risk
of an accident.
Do not switch off the ignition while driving.
! Always observe the ground clearance of
the vehicle and avoid obstacles. On
vehicles with a step, ground clearance is
further restricted. Obstacles can damage
the vehicle.
If you must drive over obstacles, drive
especially slowly and carefully. If
necessary, have another person direct you.
Drive sensibly–s ave fuelIn orde
rto save fuel, observe the following
tips:
X The tires should always be inflated to the
recommended tire pressure.
X Remove unnecessary loads.
X Remove roof carriers when they are not
needed.
X Warm up the engine at low engine speeds.
X Avoid frequent acceleration or braking.
X Have all maintenance work carried out as
indicated by the service intervals in the
Maintenance Booklet or by the service
interval display.
Fuel consumption also increases when
driving in cold weather, in stop-start traffic
and in mountainous terrain. Overrun cutoff If you are in overrun mode and take your foot
off the accelerator pedal, the fuel supply is
cut off when the engine speed is out of the
idle speed control range.
Drinking and driving
G
WARNING
Drinking and driving and/or taking drugs and
driving are very dangerous combinations.
Even a small amount of alcohol or drugs can
affect your reflexes, perceptions and
judgment.
The possibility of a serious or even fatal
accident are greatly increased when you drink
or take drugs and drive.
Do not drink or take drugs and drive or allow
anyone to drive who has been drinking or
taking drugs.
Emission control G
WARNING
Combustion engines emit poisonous exhaust
gases such as carbon monoxide. Inhaling
these exhaust gases leads to poisoning. There
is a risk of fatal injury. Therefore never leave
the engine running in enclosed spaces
without sufficient ventilation.
Certain engine systems are designed to keep
the level of poisonous substances in exhaust
fumes within legal limits.
These systems only work optimally if they are
maintained exactly in accordance with the
manufacturer's specifications. Any work on
the engine should therefore be carried out by
qualified and authorized technicians at a
Sprinter dealer.
The engine settings must not be changed
under any circumstances. In addition, all
specific maintenance work must be carried
out at regular intervals and in accordance
with the service requirements of the dealer 148
Driving tipsDriving and parking

Problem Possible causes/consequences and
0004 Solutions
0013
The yellow air
filter indicator
lamp is lit while
the engine is
running. The service limit for the air filter has been reached. The air filter
is dirty.
X
Have the air filter element replaced as soon as possible at a
qualified specialist workshop. 000A
The yellow tire
pressure
monitor warning
lamp comes on. G
WARNING
The tire pressure monitor indicates a rapid or severe loss of
pressure in at least one tire.
X Stop the vehicle without making any extreme steering
maneuvers or braking suddenly. Pay attention to the traffic
conditions while doing so.
X Check the tires and correctt he tire pressure. If a tire continues
to lose pressure, it must be replaced. Replace damaged tires
immediately.
The warning light will go out after the flat tire has been rectified
and you have been driving for a few minutes.
X Vehicles with steering wheel buttons: also observe the
messages in the display (Y page 192).000A
US vehicles
only:
The yellow tire
pressure
monitor warning
lamp flashes for
60 seconds and
then remains lit. The tire pressure monitor has malfunctioned.
X
Have the tire pressure monitor and the wheels checked at a
qualified specialist workshop. 000E
The yellow water
separator
indicator lamp is
lit when the
ignition is
switched on. The water that has collected in the water separator of the fuel filter
has reached the maximum level.
X
Drain the water separator (Y page 247).218
Indicator and warning lamps in the instrument clusterOn-board computer and displays

X
To use the cigarette lighter: turn the key
to position 1in the ignition lock.
X Press in cigarette lighter 0005.
The cigarette lighte rwill pop out
automatically when the heatin gelemen tis
red-hot.
X Pull the cigarette lighter out of the socket
by its handle. 12
Vsocket
! Only use the 12 V socket (25 A) on the
center console for connecting the tire
inflatio ncompressor (Premium tire
sealant). You may otherwise damage the
electrical systems of the vehicle. Socket on the lower section of the center console
0005 12 V socket (25 A)
The 12 Vsockets for accessories are:
R at the bottom of the center console (12 V,
25 A)
R on the inside of the driver's seat frame
(12 V, 15 A) R
in the respective corner trim next to the
rear doors in the passenger compartment
(12 V, 15 A)
R in the cargo compartment next to the left
rear door (12 V, 15 A)
You can use the 12 V sockets (15 A) for
accessories with a maximu mpower
consumption of 180 W. You can connect
accessories with a maximum power
consumption of 300 W to the 12 V socket
(25 A) on the lower section of the center
console.
i The sockets are supplied with power even
when the key is removed from the ignition
lock. If accessories, e.g. a coolbox, remain
connected while the engine is not running,
the battery will discharge. Mobile phone
Important safety notes
G
WARNING
If you operate information systems and
communication equipment integrated in the
vehicle while driving, you will be distracted
from traffic conditions. You could also lose
control of the vehicle. There is a risk of an
accident.
Only operate the equipment when the traffic
situation permits. If you are not sure that this
is possible, park the vehicle paying attention
to traffic conditions and operate the
equipment when the vehicle is stationary.
You must observe the legal requirements for
the country in which you are currently driving
when operating mobile phones.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approximately
14 m) every second.
You and others can suffer health-related
damage through electromagnetic radiation.
By using an exterior antenna, a possible
health risk caused by electromagnetic fields, 228
Mobile phoneStowing and features

tire inflatio
ncompressor to run for at least
10 minutes until tire sealant bottle 0019is
completely empty and the tire pressure is
at least 300 kPa (3.0 bar/43.5 psi).
If possible, inflate the tire to the
recommended tire pressure. You will find a
table of recommended tire pressure on the
Tire and Loading Information placard 8
or
the tire pressure plate on the B-pillar on the
driver's side of the vehicle ( Ypage 278).
X Then press 0on tire inflation compressor
switch 0005.
The tire inflation compressor is
deactivated.
X Quickly slide knob 001Bto the stop in valve
core extractor 001D.
X Turn knob 001Bclockwise until the valve core
is firmly screwed into tire valve 001E.
i Do not pull valve core extractor 001Doff tire
valve 001Ewhile the valve core is unscrewed
from tire valve 001E.The tire sealant could
otherwise run out and get on your skin or
clothes.
X Press lever 001Cand pull valve core extractor
001D from tire valve 001E.
X Screw the valve cap onto tire valve 001E.
X Observe the following notes and
instructions:
R
Tire pressure of 300 kPa (3.0 bar/
43.5 psi) not reached (Y page 301).
R Tire pressure of 300 kPa (3.0 bar/
43.5 psi) reached (Y page 301). Twin tires, inner wheel X
Unscrew the valve cap from valve
extension 001Aon the defective wheel.
X Screw valve core extractor 001Bclockwise as
far as it will go onto valve extension 001A.
X Screw valve core extractor 001B
approximately a further 0003turn to release
valve extension 001A.
X Unscrew valve extension 001Aand the valve
core extractor 001Bcounter-clockwise from
tire valve 001F.
X Unscrew valve extension 001Afrom valve
core extractor 001B. X
Pull knob 001Dout of valve core extractor
001B as far as it will go.
X Screw valve core extractor 001Bclockwise
onto tire valve 001F.
X Press knob 001Dinto the valve core of valve
001F, turning it gently as you do so, until the
shaft of valve core extractor 001Bengages.
8 Only for vehicles with a gross vehicle weight of less than 10,000 lbs(4,536 kg). 298
Flat tireWheels and tires

X
Turn knob 001Dcounter-clockwise until the
valve core is unscrewed.
X Pull knob 001Dout of valve core extractor
001B as far as it will go.
This pulls the valve core into valve core
extractor 001Band seals it against valve core
extractor stop 001B.
X Hang tire sealant bottle 0019in the
uppermost wheel ventilation hole 001C.
X Push angled valve adapter 001Elocated on
the hose of tire sealant filler bottle 0019as
far as it will go on to valve core extractor
001B and fix it in place.
X Make sure that the pressure release screw
on pressure gauge 0023is closed.
X Connect connector 0024to the 12 V socket
(12 V, 25 A, 300 W) on the center console
(Y page 228).
X Start the engine.
X Press switch 0005on the tire inflation
compressor to move to position I.
The tire inflation compressor is activated.
The tire sealant is then pumped into the tire
and the tire pressure is increased. Allow the
tire inflation compressor to run for at least
10 minutes until tire sealant bottle 0019is
completely empty and the tire pressure is
at least 300 kPa (3.0 bar/43.5 psi).
If possible, inflate the tire to the
recommended tire pressure. You will find a
table of recommended tire pressure on the
Tire and Loading Information placard 9
or
the tire pressure plate on the B-pillar on the
driver's side of the vehicle ( Ypage 278).
X Then press 0on tire inflation compressor
switch 0005.
The tire inflation compressor is
deactivated.
X Quickly slide knob 001Dto the stop in valve
core extractor 001B.
X Turn knob 001Dclockwise until the valve core
is firmly screwed into tire valve 001F.i
Do not pull valve core extractor 001Bfrom
tire valve 001Fwhile the valve core is
unscrewed from tire valve 001F. The tire
sealant could otherwise run out and get on
your skin or clothes.
X Pull knob 001Dout of valve core extractor
001B as far as it will go.
X Unscrew valve core extractor 001Bcounter-
clockwise from tire valve 001F.
X Screw valve extension 001Aonto tire valve
001F and tighten it.
X Screw the valve cap onto valve extension
001A.
X Observe the following notes and
instructions:
R
Tire pressure of 300 kPa (3.0 bar/
43.5 psi) not reached (Y page 301).
R Tire pressure of 300 kPa (3.0 bar/
43.5p si) reached (Y page 301).
9 Only for vehicles with a gross vehicle weight of less than 10,000 lbs(4,536 kg). Flat tire
299Wheels and tires Z

Twin tires, outer wheel
Valve tool with handle and turning piece
001A
Handle
001B Turning piece
Tire valve 001Cis located on the inne rside of
the outer wheel. It should be positioned
horizontally on the left side of the wheel for
the repair process.
X Remove the cap from valve 001Con the
defective tire.
X Guide the valve tool through the hole in the
wheel and push it onto tir evalve 001C.
X Hold handle 001Aof the valve tool with one
hand and unscrew the valv ecore with the
other hand using rotating collar 001Bof the
valve tool.
X Remove the valve tool through the gap
carefully, so that the valve core remains
engaged in the valve tool. X
Hang tire sealant bottle 0019in the upper
ventilation hole in the wheel using hook
001E.
X Push angled valve adapter 001Dlocated on
the hose of tire sealant filler bottle 0019as
far as it will go onto valve 001Cand fix it in
place.
X Make sure that the pressure release screw
on pressure gauge 0023is closed.
X Connect connector 0024to the 12 V socket
(12 V, 25 A, 300 W) on the center console
(Y page 228).
X Start the engine.
X Press switch 0005on the tire inflation
compressor to position I.
The tire inflation compressor is activated.
The tire sealant is then pumped into the tire
and the tire pressure is increased. Let the
tire inflation compressor run until tire
sealant bottle 0019is completely empty.
X After approximately 15 seconds, press 0on
tire inflation compressor switch 0005.300
Flat tireWheels and tires