2013 MERCEDES-BENZ SL-Class brake

Course-correcting brake application
G
WARNING
Ac ourse-correcting brake application cannot
always prevent a collision. There is a risk of
an accident.
Always steer, brake or accelerate yourself,
especially if Active Blind Spot Assist warns
you or makes a course-correcting brake
application. Always maintain a safe distance
at the sides. G
WARNING
Active Blind Spot Assist does not detect all
traffic situations and road users. In very rare
cases, the system may make an inappropriate
brake application. There is a risk of an
accident.
An inappropriate brake application may be
interrupted at any time if you steer slightly in
the opposite direction or accelerate. Always
make sure that there is sufficient distance on
the side for other traffic or obstacles. If a course-correcting brake application
occurs, red warning lamp
0002flashes in the exterior mirror and a dual warning tone
sounds. In addition, display
0003appears in the
multifunction display.
If Active Blind Spot Assist detects a risk of a
lateral collision in the monitoring range, a
course-correcting brake application is carried
out. This is meant to assist you in avoiding a
collision.
The course-correcting brake application is
available in the speed range between 20 mph
(30 km/h) and120 mph (200km/h).
Either a very slight course-correcting brake
application, or none at all, may occur if:
R there are vehicles or obstacles, e.g. crash
barriers, located on both sides of your
vehicle.
R a vehicle approaches you too closely at the
side.
R you have adopted a sporty driving style with
high cornering speeds.
R you clearly brake or accelerate.
R a driving safety system intervenes, e.g.
ESP ®
or PRE-SAFE ®
Brake.
R ESP ®
is switched off.
R a loss of tire pressure or a defective tire is
detected.
Switching on Active Blind Spot Assist X
Make sure that the radar sensor system
(Y page 235) and Active Blind Spot Assist Driving systems
217Driving and parking Z

(Y
page 231 )are activated in the on-board
computer.
X Turn the SmartKey to position 2in the
ignitio nlock.
Warning lamps 0002in the exterior mirrors
light up red for approximately
1.5 seconds and then turn yellow.
Active Lane Keeping Assist Important safety notes
If you fail to adapt your driving style, Active
Lane Keeping Assist can neither reduce the
risk of accident nor override the laws of
physics. Lane Keeping Assist cannot take into
account the road, traffic and weather
conditions. Lane Keeping Assist is merely an
aid. You are responsible for the distance to
the vehicle in front, for vehicle speed, for
braking in good time and for staying in lane.
Active Lane Keeping Assist cannot
continuously keep your vehicle in its lane. G
WARNING
Active Lane Keeping Assist cannot always
clearly detect lane markings.
In such cases, Active Lane Keeping Assist
can:
R give an unnecessary warning and then
make a course-correcting brake application
to the vehicle
R not give a warning or intervene
There is a risk of an accident.
Always pay particular attention to the traffic
situation and keep within the lane, especially
if Active Lane Keeping Assist alerts you.
Terminate the intervention in a non-critical
driving situation. The system may be impaired or may not
function if:
R
there is poor visibility, e.g. due to
insufficient illumination of the road, or due
to snow, rain, fog or spray
R there is glare, e.g. from oncoming traffic,
the sun or reflections (e.g. when the road
surface is wet)
R the windshield is dirty, fogged up, damaged
or covered, for instance by a sticker, in the
vicinity of the camera
R there are no, several or unclear lane
markings for a lane, e.g. in areas with road
construction work
R the lane markings are worn away, dark or
covered up, e.g. by dirt or snow
R the distance to the vehicle in front is too
small and the lane markings thus cannot be
detected
R the lane markings change quickly, e.g.
lanes branch off, cross one another or
merge
R the road is narrow and winding
R there are strong shadows cast on the lane
General notes Active Lane Keeping Assist monitors the area
in front of your vehicle by means of
camera 0002at the top of the windshield. Active
Lane Keeping Assist detect slane markings on
the road and warns you before you leave your
lane unintentionally. If you do no treact to the
warning, a lane-correcting application of the
brakes can bring the vehicle back into the
original lane. 218
Driving systemsDriving and parking

If you select
km on the on-board computer in
the Display Unit Speed-/Odometer function (
Ypage 232), Active Lane Keeping
Assist is activated starting at a speed of
60 km/h. If the miles display unit is selected,
the assistance range begins at 40 mph.
Warning vibration in the steering wheel
A warning may be given if a front wheel
passes over a lane marking. It will warn you
by means of intermittent vibration in the
steering wheel for up to 1.5 seconds.
In order that you are warned only when
necessary and in good time if you cross the
lane marking, the system recognizes certain
conditions and warns you accordingly.
The warning vibration occurs earlier if:
R you approach the outer lane marking on a
bend.
R the road has very wide lanes, e.g. a
freeway.
R the system recognizes solidl ane markings.
The warning vibratio noccurs later if:
R the road has narrow lanes.
R you cut the corner on a bend.
Lane-correcting brake application G
WARNING
A lane-correcting brake application cannot
always bring the vehicle back into the original
lane. There is a risk of an accident.
Always steer, brake or accelerate yourself,
especially if Active Lane Keeping Assist warns
you or makes a lane-correcting brake
application. G
WARNING
Active Lane Keeping Assist does not detect
traffic conditions or road users. In very rare
cases, the system may make an inappropriate
brake application, e.g. afte rintentionally
driving ove rasolid lane marking. There is a
risk of an accident.
An inappropriate brake application may be
interrupted at any time if you steer slightly in the opposite direction. Always make sure that
there is sufficient distance on the side for
other traffic or obstacles.
In rare cases, Active Lane Keeping Assist can
recognize unclear markings or particular
structures on the roadway as solid lane
markings. An inappropriate brake application
may be interrupted at any time if you steer
slightly in the opposite direction. If a lane-correcting brake application occurs,
display
0002appears in the multifunction
display.
If you leave your lane, under certain
circumstances the vehicle will brake briefly
on one side. This is meant to assist you in
bringing the vehicle back to the original lane.
This function is available in the range between
40 mph and 120 mph (60 km/h and
200 km/h).
A lane-correcting brake application can only
be made after driving over a solid,
recognizable lane marking. Before this, a
warning must be given by means of
intermittent vibration in the steering wheel.
In addition, a lane with lane markings on both
sides must be recognized. The brake
application also slightly reduces vehicle
speed.
i A further lane-correcting brake
application can only occur after your
vehicle has returned to the original lane. Driving systems
219Driving and parking Z

No lane-correcting brake application occurs
if:
R
you clearly and actively steer, brake or
accelerate.
R you cut the corner on a sharp bend.
R you have switched on the turn signals.
R a driving safety system intervenes, e.g.
ESP ®
, PRE-SAFE ®
Brake or Active Blind
Spot Assist.
R you have adopted a sporty driving style with
high cornering speeds or high rates of
acceleration.
R ESP ®
is switched off.
R the transmission is not in position D.
R a loss of tire pressure or a defective tire has
been detected and displayed.
Active Lane Keeping Assist does not detect
traffic situations or road users. An
inappropriate brake application may be
interrupted at any time if you:
R steer slightly in the opposite direction
R switch on the turn signal
R clearly brake or accelerate
Al ane-correcting brake applicatio nis
interrupted automatically if:
R a driving safety system intervenes, e.g.
ESP ®
, PRE-SAFE ®
Brake or Active Blind
Spot Assist.
R lane markings can no longer be recognized.
Switching on Active Lane Keeping Assist X
Switch on Active Lane Keeping Assist using
the on-board computer; to do so, select
Standard or
Adaptive (Y
page 231).
Symbol 0002appears in the multifunction
display. If
Standard is selected, no warning
vibration occurs if:
R you have switched on the tur nsignals .In
this event, the warnings are suppressed
for a certain period of time.
R a driving safety syste mintervenes, such
as ABS, BAS or ESP ®
.
If Adaptive is selected, no warning
vibration occurs if:
R you have switched on the tur nsignals .In
this event, the warnings are suppressed
for a certain period of time.
R a driving safety syste mintervenes, e.g.
ABS, BAS or ESP ®
.
R you accelerate hard, e.g .kickdown.
R you brake hard.
R you steer actively, e.g. swerve to avoid
an obstacle or change lanes quickly.
R you cut the corner on a sharp bend. 220
Driving systemsDriving and parking

0024
Outside temperature or speed
(Ypage 233)
0025 Time (Y page 304)
X To show the menu bar 0026:press the
0004 or0008 button on the steering wheel.
Menu bar 0026disappears after a few seconds.
Text field 0027shows the selected menu or
submenu as well as display messages.
The following messages may appearint he
multifunction display:
0038 Upshift indicator (Y page 170)
003600140037 Active Parking Assist (Y page 206)
CRUISE Cruise control (Y
page 183)
0002 Adaptive high-beam Assist
(Ypage 132)
0003 ATTENTION ASSIST (Y page 213)
000F ECO start/stop function
(Ypage 158)
0001 Active Lane Keeping Assist
(Ypage 218)
0001 HOLD function (Y page 195)
0001 PRE-SAFE ®
Brake (Y page 79) Menus and submenus
Menu overview
Press the 0004or0008 button on the
steering wheel to call up the menu bar and
select a menu.
Operating the on-board computer
(Y page 223).
Depending on the equipment installed in the
vehicle, you can call up the following menus:
R Trip menu (Y
page 225)
R Navi menu (navigation instructions)
(Y page 226)
R Audio menu (Y
page 228)
R Tel menu (telephone) (Y
page 229)
R DriveAssist menu (assistance)
(Y page 230)
R Service menu (Y
page 231) R
Settings menu (Y
page 232)
R AMG menu in AMG vehicles (Y
page 236) Trip menu
Standard display X
Press and hold the 001Fbutton on the
steering wheel until the Trip menu with
trip odometer 0002and odometer 0003is
shown.
Trip computer "From Start" or "From
Reset" Example: trip computer "From start"
0002
Distance
0003 Time
0027 Average speed
0026 Average fuel consumption
X Press the 0004or0008 button on the
steering wheel to select the Trip menu.
X Press 0006or0007 to select From Start or
From Reset .
The values in the From Start submenu are
calculated from the start of a journey whilst
the values in the From Reset submenu are
calculated from the last time the submenu
was reset (Y page 226).
The From Start trip computer is
automatically reset when: Menus and submenus
225On-board computer and displays Z

Dialing a number from the phone book
X
Press the 0004or0008 button on the
steering wheel to selec tthe Tel menu.
X Press the 0006,0007or000F button to call
up the phone book.
X Press the 0006or0007 button to select the
desired name.
or
X To begin rapid scrolling: press and hold
the 0006 or0007 button for longer than
one second.
Rapid scrolling stops when you release the
button or reach the end of the list.
X If only one telephone number is stored
for a name: press the0017or000F button
to start dialing.
or
X If there is more than one number for a
particular name: press the0017or000F
button to display the numbers.
X Press the 0006or0007 button to select the
number you want to dial.
X Press the 0017or000F button to start
dialing.
or
X To exit the telephone book: press the
003C or001F button.
Redialing The on-board computer saves the last names
or numbers dialed in the redial memory.
X Press the 0004or0008 button on the
steering wheel to select the Tel menu.
X Press the 0017button to switch to the
redial memory.
X Press the 0006or0007 button to select the
desired name or number.
X Press the 0017or000F button to start
dialing.
or
X To exit the redial memory: press the
003C or001F button. Assistance menu
Introduction In the
DriveAssist menu, you have the
following options:
R AMG vehicles only: set the vehicle level
(Y page 200)
R show the distance display (Y page 230)
R activate/deactivate the PRE-SAFE ®
Brake
(Y page 231)
R activate/deactivate ATTENTION ASSIST
(Y page 231)
R activate/deactivate Active Blind Spot
Assist (Y page 231)
R activate/deactivate Active Lane Keeping
Assist (Y page 231)
Showing the distance display X
Press the 0004or0008 button on the
steering wheel to select the
DriveAssist. menu.
X Press the 0006or0007 button to select
Distance Display .
X Press 000F.
The DISTRONIC PLUS distance display
appears in the multifunction display
(Y page 192). 230
Menus and submenusOn-board computer and displays

Activating/deactivating PRE-SAFE
®
Brake PRE-SAFE
®
Brake is only available in vehicles
with DISTRONIC PLUS.
X Press the 0004or0008 button on the
steering wheel to select the DriveAssistmenu.
X Press the 0006or0007 buttonto select
PRE-SAFE Brake .
X Press 000F.
The current selection is displayed.
X To activate/deactivate: press000F
again.
When PRE-SAFE ®
Brake is activated, the
multifunction display shows the 0001symbol
as long as the HOLD function is not activated
(Y page 195).
Vehicles with Active Parking Assist: if
PARKTRONIC is activated and you are driving
at a speed under 22 mph (35 km/h), the 0014
Active Parking Assist symbol is shown instead
of the 0001symbol (Y page 206).
For more information on PRE-SAFE ®
Brake,
see (Y page 79).
Activating/deactivating ATTENTION
ASSIST X
Press the 0004or0008 button on the
steering wheel to select the DriveAssistmenu.
X Press the 0006or0007 button to select
Attention Asst. X
Press 000F.
The current selection is displayed.
X To activate/deactivate: press000F
again.
When ATTENTION ASSIST is activated, the
0003 symbol appears in the multifunction
display when the ignition is on.
For further information about ATTENTION
ASSIST, see (Y page 213). Activating/deactivating Active Blind
Spot Assist X
Press the 0004or0008 button on the
steering wheel to select the DriveAssist menu.
X Press the 0006or0007 button to select
Blind Spot Asst. .
X Press 000F.
The current selection is displayed.
X To activate/deactivate: press000F
again.
For further information about Active Blind
Spot Assist, see (Y page 214).
Activating/deactivating Active Lane
Keeping Assist X
Press the 0004or0008 button on the
steering wheel to select the DriveAssist menu.
X Press the 0006or0007 button to select
Lane Keep. Asst. X
Press 000F.
The current selection is displayed.
X Press the 000Fbutton to confirm.
X Press 0007or0006 to set Off ,
Standard or
Adaptive .
X Press the 000Fbutton to save the setting.
When Active Lane Keeping Assist is activated,
the 0001 symbol appears in the multifunction
display when the ignition is on.
For further information about Active Lane
Keeping Assist, see (Y page 218). Maintenance menu Menus and submenus
231On-board computer and displays Z

Vehicle
Activating/deactivating the automatic
doo rlocking mechanism
X Press the 0004or0008 button on the
steering wheel to selec tthe Settings menu.
X Press the 0007or0006 button to select the
Vehicle submenu.
X Press the 000Fbutton to confirm.
X Press 0007or0006 to select the
Automatic Door Lock function.
When the Automatic Door Lock function
is activated, the vehicle doors are displayed
in red in the multifunction display.
X Press the 000Fbutton to save the setting.
If you activate the Automatic Door Lock function, the vehicle is centrally locked above
a speed of around 9 mph (15 km/h).
For further information on the automatic
locking feature, see (Y page 92).
Activating/deactivating the acoustic
locking verification signal
If you switch on the Acoustic Lock function,
an acoustic signal sounds when you lock the
vehicle.
X Press the 0004or0008 button on the
steering wheel to select the Settingsmenu.
X Press the 0007or0006 button to select the
Vehicle submenu.
X Press the 000Fbutton to confirm.
X Press the 0007or0006 button to select the
Acoustic Lock function.
If the Acoustic Lock function is activated,
the 000D symbol in the multifunction
display lights up red.
X Press the 000Fbutton to save the setting. Activating/deactivating the radar sensor
system
X
Press the 0004or0008 button on the
steering wheel to select the Settings menu.
X Press the 0007or0006 button to select the
Vehicle submenu.
X Press 000Fto confirm.
X Press the 0006or0007 button to select
Radar Sensor (See Oper. Manual): .
You will see the selected setting Enabled or
Disabled .
X Press the 000Fbutton to save the setting.
The following systems are switched off when
the radar sensor system is deactivated:
R DISTRONIC PLUS (Y page 186)
R BAS PLUS (Y page 74)
R PRE-SAFE ®
Brake (Y page 79)
R Active Blind Spot Assist (Y page 214)
Convenience Activating/deactivating the EASY-
ENTRY/EXIT feature
G
WARNING
You must make sure no one can become
trapped or injured by the moving steering
wheel when the easy-entry/exit feature is
activated.
To stop steering wheel movement, move
steering wheel adjustment lever or press one
of the memory position buttons.
Do not leave children unattended in the
vehicle, or with access to an unlocked vehicle.
Children could open the driver's door and
unintentionally activate the easy-entry/exit
feature, which could result in an accident
and/or serious personal injury.
X Press the 0004or0008 button on the
steering wheel to select the Sett. menu.
X Press the 0007or0006 button to select the
Convenience submenu.
X Press the 000Fbutton to confirm. Menus and submenus
235On-board computer and displays Z