2013 MERCEDES-BENZ S-Class light

X
Press the mirror-folding button
(Y page 116) repeatedly until you hear the
mirror engage in position.
The mirror housing is engaged again and
you can adjust the exterior mirrors as usual
(Y page 116). Automatic anti-glare mirrors
G
WARNING
If inciden tlight fro mheadlamps is prevented
from striking the sensor in the rear-view
mirror, for instance, by luggage piled too high
in the vehicle, the mirror's automatic anti-
glare function will not operate.
Incident light could then blind you. This may
distract you from the traffic conditions and,
as a result, you may cause an accident.
The rear-view mirror and the exterior mirror
on the driver's side automatically go into anti-
glare mode if the ignition is switched on and
inciden tlight fro mheadlamps strikes the
sensor in the rear-view mirror.
The mirrors do not go into anti-glare mode if
reverse gear is engaged or the interior lighting
is switched on. Parking position for the exterior
mirror on the front-passenger side
Setting and storing the parking position You can position the front-passenger side
exterior mirror in such a way that you can see
the rear wheel on that side as soon as you
engage reverse gear. You can store this
position. X
Make sure that the vehicle is stationary and
that the SmartKey is in position 2in the
ignition lock.
X Press button 0026for the exterior mirror on
the front-passenger side.
X Engage reverse gear.
The exterior mirror on the front-passenger
side moves to the preset parking position.
X Use adjustment button 0003to adjust the
exterior mirror .You should see the rear
wheel and the curb in the exterior mirror.
The parking position is stored.
i If you shift the transmission to another
position, the exterior mirror on the front-
passenger side returns to the driving
position.
i You can also store the parking position
using memory button M0002.
X Make sure that the SmartKey is in
position 2in the ignition lock.
X With the exterior mirror on the front-
passenger side activated, use
adjustment button 0003to adjust the
exterior mirror. You should see the
rear wheel and the curb in the exterior
mirror on the front-passenger side.
X Press memory button M0002 and one of
the arrows on adjustment button 0003
within three seconds.
The parking position is stored if the
exterior mirror does not move.
If the mirror moves out of position, repeat
the steps. Mirrors
117Seats, steering wheel and mirrors Z

Navi Audio Telephone Video Vehicle
Mode FM/AM radio Video DVD ECO
Map orientation Sat radio AUX Multicontour
seat/lumbar
settings
Point of interest
symbols on the map Disc Video off Rear window
blind
Traffi
csymbols on the
map Memory card EASY-ENTRY/
EXIT system
Text information on
map MUSIC
REGISTER Exterior
lighting
delayed
switch-off
000A
Topographical
map Media
Interface Interior
lighting
delayed
switch-off
000A
City view USB Ambient
lighting
000A
Freeway
information Rear 000A
Automatic
mirror fold-in
function 000A
Volume reduction AUX 000A
Locator
lighting SIRIUS service Audio off 000A
Automatic
locking Map version 000A
Interior
motion sensor 000A
Tow-away
alarm 000A
Trunk lid
opening height
restriction SPLITVIEW
SPLITVIEW allows you to simultaneously use
different COMAND functions on the front-
passenger side and on the driver's side.
Depending on the viewing angle of the display
(from the driver's seat or from the front-
passenger seat), you will see two different
displays.126
At
ag lanceCOMAND

switch SPLITVIEW on and off
(Y
page 129).
The SPLITVIEW screen remains on for
approximately 30 minutes after the SmartKey
has been turned to position 0in the ignition
lock. After this time or after the SmartKey has
been removed, the settings on the front-
passenger side are saved for approximately
30 minutes longer. After this period,
reactivation on the front-passenger side
means that the settings from the driver's side
will be used.
Cordless headphones for the front
passenger There are different cordless headphones for
the front passenger and the rear
compartment.
The cordless headphones for the front
passenger can be identified by SPLITVIEW
symbol
0002on the headband.
The cordless headphones for the front
passenger cannot be used in the rear
compartment.E qually, the headphones for
the rear compartment cannot be used by the
fron tpassenger.
Swiveling the COMAND displa yand
setting the brightness You can swivel the COMAND display
5
.T he
buttons are located beside the COMAND
display. Swiveling
0002
To swivel the display to the left
0003 To swivel the display to the right
Setting the brightness 0002
Brightness of the instrument cluster
lighting
0003 Brightness of the COMAND display
Brighter or dimmer:
X Turn control 0002or0003 clockwise or counter-
clockwise.
i If Night View Assist Plus is activated, only
the brightness of the multifunction display
is adjusted with control 0002.
Display design
When the default settings are selected, the
display automatically switches between day
design and night design.
You can change these settings using
COMAND (Y page 147).
5 Not with SPLITVIEW. 128
At
ag lanceCOMAND

Cleaning instructions
!
Do no ttouch the COMAND display .The
display has a very sensitive high-gloss
surface; there is a risk of scratching. If you
have to clean the screen, however, use a
mild cleaning agent and a soft, lint-free
cloth.
The display must be switched off and have
cooled down before you start cleaning. Clean
the display screen, when necessary, with a
commercially available microfiber cloth and
cleaning agent for TFT/LCD displays. Then,
dry the surface with a dry microfiber cloth.
Avoid using alcoholic thinners, gasoline or
abrasive cleaning agents. These could
damage the display surface. Do not apply
pressure to the display surface when cleaning
it, as this could cause irreversible damage. Remote control
Overview You can use the remote control to operate the
COMAND display, SPLITVIEWa nd either one
of the rear-compartment screens. 0002
To switch the screen on/off (Rea rSeat
Entertainment System only)
0003 To switch the button lighting on/off 0026
To select the screen for remote control
operation (COMAND ,SPLITVIEW ,L
REAR and REAR Rcan be selected)
0025 To select a menu or menu item
0023 To confirm a selection or setting
0024 Mute
0014 To adjust the volume (for corded
headphones only)
0015 COMAND: to set the station, skip track,
fast forward/rewind, for example. Rear
Seat Entertainment System: skip track,
fast forward/rewind
0016 COMAND: to select a station from
presets, select a track, enter directly,
enter a phone number, for example. Rear
Seat Entertainment System: to select a
track, enter directly
0017 To exit a menu (back)
X Point the remote control at the
corresponding screen and execute the
functions by pressing the corresponding
buttons.
i The remote control's function may be
restricted depending on the angle at which
it is pointed at the respective screen.
Selecting the screen for the remote
control X
Turn thumbwheel 0026until the desired
display is highlighted in the window.
Switching the screen on/off (Rear Seat
Entertainment System only) If the SmartKey is in the ignition lock in
position
0or 1or if the SmartKey is not in the
ignition lock, the rear screens will switch off
after 30 minutes. Before the screens switch
off, they show a message to this effect.
You can switch the screen sback on.
However, this will discharge the starter
battery. At
ag lance
129COMAND Z

X
Point the remote control at the rear-
compartment screen which has been
selected for remote operation.
X Press button 0002on the remote control.
The respective rear screen switches on or
off.
i You can only switch the screens on using
the remote control if the ignition is
switched on.
Switching the button lighting on/off X
Press button 0003on the remote control.
Depending on the previous status, the
button lighting is switched on or off.
i If you do not use the remote control for
about 15 seconds, the button lighting
switches off automatically.
Mute X
Press button 0024on the remote control.
The sound is switched on/off.
Adjusting the volume This function is available for SPLITVIEW and
for the Rear Seat Entertainment System in
conjunction with corded headphones.
X Press one of buttons 0014on the remote
control.
The volume of the currently selected audio
or video source changes.
For COMAND, you can also adjust the
volume for phone calls and navigation
messages.
Selecting amenu/menu item and
confirming your selection X
Press the 0009000C000A buttons to
selec tthe menu/menu item and press the
000C button to confirm. 130
At
ag lanceCOMAND

You can enter the characters using either the
character bar or the number keypad. In the
selection list, you selec
tanentry to copy it to
the address entry menu.
Option 1: city list with character bar
X Call up the city list with character bar
(Y page 157).
The alphabetically sorted city list shows the
first available entries. Entering characters using the character
bar
X
Select N by turning COMAND controller
0031001C0032 and confirm with 0021.0002
N character entered by user
0003 ANTICOKE characters automatically
added by COMAND
0026 Listentry tha tmost closely resembles the
current entry by the user
0025 To switch to the selection list
0023 To delete an entry
0024 Characters not currently available
0014 Characters currently available 0015
Currently selected character
0016 Character bar
0017 To cancel an entry
0018 List
The list 0018shows all available town names
beginning with N .T
he list entry that is best
suited to previous user entries is always
highlighted in the first position 0026,
NANTICOKE in the example.
All characters that have been entered are
displayed in black, the letter N in the
example 0002.The letters that are added
automatically by COMAND are displayed in
gray 0003,ANTICOKE in the example.
Character bar 0016shows the letters still
available for selection in black 0014.These can
be selected; in the example, the letter O is
highlighted 0015.Which characters remain
available depends on the characters already
entered by the user and on the data stored in
the digital map. Characters that are no longer
available are shown in gray 0024.
X Select E ,
W , space,
Y in order and confirm
each with 0021. Entering characters using the number
keypad
X
Press the telephone keypad's number key
0036 twice in quick succession, to enter
the letter N .
The character appears at the bottom of the
display when the key is pressed. The first
available letter is highlighted. 134
At
ag lanceCOMAND

You see which characters you can enter with
that key. Each time the key is pressed, the
nex tcharacter is selected.
Example: key 0036:
R press once = M
R press twice =N
R press three times =O
X Wait until the character display goes out.
The entries matching your input are shown
in the list.
X Enter E ,
W , space,
Y with the corresponding
keys.
i The space is entered using number key
0004.
Further functions in the list with
character bar
X To delete characters: select0004by sliding
001C0006 and turning 0031001C0032the COMAND
controller and press 0021to confirm.
X To delete an entry: select0004and press
and hold 0021the COMAND controller until
the entire entry has been deleted.
X To switch the character set: select
001D and press 0021to confirm.
X To cancel an entry: select the0002symbol
in the bottom left of the character bar and
press 0021to confirm.
or
X Press the 0001back button.
The address entry menu appears.
X To accept the first list entry: press and
hold 0021the COMAND controller until the
address entry menu appears.
The accepted list entry is shown there.
Calling up the list as aselection list
Select the desired city fro mthe selection list.
If there are several entries for a city or if
several cities of the same name are stored,
then 0003 is highlighted in the character bar.
X Press 0021the COMAND controller. It is also possible to switch the city list to the
selection list at any time during character
input.
X Slide 0021the COMAND controller
repeatedly until the city list appears as a
selection list.
or
X Select 0003in the character bar by turning
0031001C0032 the COMAND controller and press
0021 to confirm.
Option 2: city list as selection list
COMAND either shows the selection list
automatically or you can call up the selection
list from the list with character bar.
The example shows the selection list after the
city NEW YORK has been entered. The entry is
highlighted automatically. X
Confirm NEW YORK with COMAND
controller 0021.
The address entry menu appears. You can
now enter a street, for example. At
ag lance
135COMAND Z

Dolby
®
Digital dts™
MLP™
Selecting settings fo
rthe Bang &Olufsen
sound system
Calling up the menu
X Select Sound .
X Highlight Bang&Olufsen .
X Press 0021.
Am enu appears.
A 002C dot in front of an entry indicates the
current setting.
Selecting the setting for True Image™
X Turn 0031001C0032 or slide 002A001C0006and highlight
reference or
3D Sound .
X Press 0021. Focusing the sound setting 0002
Current position of the sound setting
X Select Sound Mode in the menu.
X Turn 0031001C0032 or slide 002A001C0006and highlight
front ,
all or
rear .
X Press 0021.
X To exit the menu: press the0001back
button beside the COMAND controller.
or
X Slide 003C001C003D.
i Please bear the following in mind:
You will achieve the best sound results on
your Bang &Olufsen sound system by
playing high-quality audio DVDs and CDs.
MP3 tracks should have abit rate of at least
224 kbit/s.
When playing using an iPod ®
, the bit rate
should also be at least 224 kbit/s.
For optimum playback quality:
XDeactivate the EQ setting on the
iPod ®
.
Surround sound playback does not
function for mono signal sources, such as
the medium wave range (MW) in radio
mode.
On some stereo recordings, the sound
characteristics may differ from
conventional stereo playback. 142
At
ag lanceCOMAND