2013 MERCEDES-BENZ S-Class warning

0002
Gear indicator
0003 Upshif tindicator
0026 Engine oil temperature
0025 Coolant temperature
Upshift indicator up 0003
indicates tha tthe
engine has reached the overrevving range
when in the manual gearshift program.
Upshift indicator up 0003
fades out other
messages until you have shifted up.
When the engine oil temperature is below
80 †, the oil temperature is shown in blue.
Avoid driving at full engine output during this
time.
i S 63 AMG: the status of the ECO start/
stop function (Y page 310) is also shown.
RACETIMER Displaying and starting RACETIMER
G
WARNING
The RACETIMER feature is only for use on
roads and in conditions where high speed
driving is permitted. Racing on publicr oads is
prohibited under all circumstances. The driver
is and must always remain responsible for
following posted speed limits.
You can use the RACETIMER to store lap
times.
With RACETIMER, you cannot use the 000F
and 0010 buttons on the steering wheel to
adjust the volume.
X Press the 0009or000C button on the
steering wheel to select the AMG menu.
X Press the 000Abutton repeatedly until the
RACETIMER is shown. 0002
Gear indicator
0003 Seconds indicator
0026 RACETIMER
0025 Lap
You can start the RACETIMER when the
engine is running or if the SmartKey is in
position 2in the ignition lock.
X To start: press the 000Fbutton to start the
RACETIMER.
X To display the intermediate time: press
the 0010 button to show the intermediate
time.
The intermediate time is displayed for five
seconds.
X To stop: press the 000Fbutton to stop the
RACETIMER.
The RACETIMER interrupts timing when you
stop the vehicle and turn the SmartKey to
position 1in the ignition lock. When you turn
the SmartKey to position 2or 3and then
press the 000Fbutton, timing is continued.
Storing the lap time and starting anew lap
It is possible to store a maximum of sixteen
laps.
X Press the 0010button on the steering
wheel to show the intermediate time during
timing.
The intermediate time is displayed for five
seconds.
X Press the 0010button again within five
seconds.
The displayed intermediate tim eis stored
as a lap time. 382
Menus and submenusOn-board computer and displays

0002
Lap
0003 Lap time
0026 Top speed during lap
0025 Lap length
0023 Average lap speed
X Press the 000Aor000B button to select a
different lap evaluation. Telephone menu
Introduction You can establish a Bluetooth
®
connection to
COMAND (Y page 199). G
WARNING
The driver's attention to the road must always
be his/her primary focus when driving. For
yours afety and the safety of others, we
recommend that you pull ove rto a safe
location and stop before placing or taking a
telephone call. If you choose to use the
telephone while driving, please use the hands-
free device and only use the telephone when
road, weather and traffic conditions permit.
Some jurisdictions prohibit the driver from
using a mobile phone while driving a vehicle.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h) , your vehicle covers
a distance of 44 feet (approximately 14 m)
every second.
X Switch on the mobile phone and COMAND
(Y page 137).
X Press the 0009or000C button on the
steering wheel to select the Telephonemenu. You will see one of the following display
messages in the multifunction display:
R
Telephone ready or the name of the
network provider :the mobile phone has
found a network and is ready to receive.
R No Service :n
o network is available, or the
mobile phone is searching for a network.
Accepting acall If someone calls you whe
nyou are in the
Telephone menu, a display message
appears in the multifunction display, for
example: X
Press the 0027button on the steering
wheel to accept an incoming call.
If you are not in the Telephone menu, you
can still accept a call.
Rejecting or ending acall X
Press the 001Fbutton on the steering
wheel.
If you are not in the Telephone menu, you can
still reject or end a call.
Dialing a number from the phone book You can use the mobile phone to enter new
telephone numbers into the phone book (see
COMAND) (Y
page 207). If you rmobile phone
is able to receive calls, you can search for and
dial a number from the phone book.
When you establish a Bluetooth ®
connection
to COMAND, COMAND reads in the phone
book of the mobile phone. This can take some
time. 384
Menus and submenusOn-board computer and displays

Deactivating/activating ESP
®G
WARNING
Under no circumstances should you
deactivate ESP ®
when the 000CESP®
warning lamp in the instrument cluster
flashes .Proceed as follows:
R when driving off, apply as little throttle as
possible.
R while driving, ease up on the accelerator
pedal.
R adapt yours peed to suit the prevailing road
and weather conditions.
Failure to observe these guidelines could
cause the vehicle to skid. ESP ®
cannot
prevent accidents resulting from excessive
speed.
For further information about ESP ®
, see
(Y page 75).
X Start the engine.
X Press 0009or000C on the steering wheel
to select the Assistance menu.
X Press the 000Aor000B buttonto select
ESP .
X Press the 0011button.
X To deactivate: press0011again.
The 0013 warning lamp in the instrument
cluster comes on. G
WARNING
When the 0013ESP®
OFF warning lamp is lit,
ESP ®
is deactivated.
If the 000C ESP®
warning lamp and the
0013 ESP®
OFF warning lamp remain lit,
ESP ®
is not available due to amalfunction.
When ESP ®
is deactivated or no toperational,
vehicle stability in standard driving
maneuvers is reduced.
Adapt your speed and driving to the prevailing
road conditions and to the non-operating
status of the ESP ®
. X
To activate: press0011again.
The 0013 warning lamp in the instrument
cluster goes out.
Activating/deactivating PRE-SAFE ®
Brake PRE-SAFE
®
Brake is only available in vehicles
with DISTRONIC PLUS.
X Press the 0009or000C button on the
steering wheel to select the DriveAssist menu.
X Press 000Aor000B to select PRE-SAFE Brake .
X Press 0011.
The curren tselection is displayed.
X To activate/deactivate: press0011
again.
When PRE-SAFE ®
Brake (Y page 77) is
activated, the multifunction display shows
the 0001 symbol as long as the HOLD
function is not activated (Y page 346).
Activating/deactivating ATTENTION
ASSIST This function is not available in HYBRID
vehicles.
X
Press the 0009or000C button on the
steering wheel to select the DriveAssist menu.
X Press the 000Aor000B button to select
Attention Assist .
X Press 0011.
The curren tselection is displayed.
X To activate/deactivate: press0011
again.
When ATTENTION ASSIST( Ypage 359) is
activated, the 0004symbol appears in the
multifunction display when the ignition is on. 386
Menus and submenusOn-board computer and displays

Display messages
General notes
G
WARNING
All categories of messages contain important information which should be take nnote of and,
where a malfunction is indicated, addressed as soon as possible at an authorized Mercedes-Benz
Center.
Failure to repair the condition noted may cause damage not covered by the Mercedes-Benz
Limited Warranty, or result in property damage or personal injury.
Display messages appear in the multifunction display.
Display messages with graphic displays may be shown in simplified form in the Operator's
Manual and may differ from the messages shown in the multifunction display.
Please respond in accordance with the display messages and follow the additional notes in
this Operator's Manual.
Certain display messages are accompanied by an audible warning tone or a continuous tone.
When you stop and park the vehicle, please observe the notes on the HOLD function
(Y page 346) and parking (Y page 327).Hiding display messages
You can hide some display messages with a low priority.
X Press the 0011or0001 button on the steering wheel to hide the display message.
The display message is cleared.
Display messages with a low priority are shown in either yellow or white.
Display messages with a high priority are shown in red.
You cannot hide display messages of the highest priority. The multifunction display shows
these messages continuously until the causes for the messages have been remedied. Message memory
The on-board computer saves certain display messages. You can call up the display messages
in the message memory.
X Press the 0009or000C button on the steering wheel and select the Service menu.
If there are display messages, the multifunction display shows, for example, 2 messages .
X Press the 000Aor000B button to select the entry, e.g. 2 messages .
X Confirm with 0011.
X Press the 000Aor000B button to scroll through the display messages.
When the ignition is switched off, all display messages are deleted, apart from some high-
priority display messages. Once the causes of the high-priority display messages have been
rectified, the corresponding display messages are also deleted. 390
Display messagesOn-board computer and displays

Safety systems
Display messages Possible causes/consequences and
0004 Solutions
0015000C
currently
unavailable See
Operator's Manual ABS (Anti-lock Braking System), ESP
®
(Electronic Stability
Program), BAS (Brake Assist), PRE-SAFE ®
,t he HOLD function and
hill start assist are temporarily unavailable.
BAS PLUS and PRE-SAFE ®
Brake may also have failed.
In addition, the 000C,0013and0015 warning lamps light up in
the instrument cluster.
ATTENTION ASSIST 19
is deactivated.
For example, the on-board voltage may be insufficient.
G WARNING
The brake system continues to function normally, but without the
functions listed above. The wheels could therefore lock if you
brake hard, for example.
The steerability and braking characteristics may be severely
affected. The braking distance in an emergency braking situation
can increase.
If ESP ®
is not operational, ESP ®
is unable to stabilize the vehicle.
There is an increased risk of skidding and an accident.
X Carefully drive a short distance on a suitable stretch of road,
making slight steering movements at a speed above 12 mph
(20 km/h).
If the display message disappears, the functions mentioned
above are available again.
If the display message continues to be displayed:
X Drive on carefully.
X Visit a qualified specialist workshop. ABS, ESP
®
, BAS, PRE-SAFE ®
, the HOLD function and hill start
assist are temporarily unavailable.
BAS PLUS and PRE-SAFE ®
Brake may also have failed.
In addition, the 000C,0013and0015 warning lamps light up in
the instrument cluster.
ATTENTION ASSIST 19
is deactivated.
For example, the on-board voltage may be insufficient.
G WARNING
The brake system continues to function normally, but without the
functions listed above. The wheels could therefore lock if you
brake hard, for example. 19
Not available on hybrid vehicles. Display messages
391On-board computer and displays Z

Display messages Possible causes/consequences and
0004 Solutions
The steerability and braking characteristics may be severely
affected. The braking distance in an emergency braking situation
can increase.
If ESP
®
is no toperational, ESP ®
is unable to stabilize the vehicle.
There is an increased risk of skidding and an accident.
X Drive on carefully.
If the display message disappears, the functions mentioned
above are available again.
If the display message continues to be displayed:
X Drive on carefully.
X Visit a qualified specialist workshop. 0015000C
inoperative See
Operator's Manual ABS, ESP
®
, BAS, PRE-SAFE ®
, the HOLD function and hill start
assist are unavailable due to a malfunction.
BAS PLUS and PRE-SAFE ®
Brake may also have failed.
The 000F (USA only)/0006 (Canada only),000C,0013and0015
warning lamps in the instrument cluster also light up.
ATTENTION ASSIST 19
is deactivated.
G WARNING
The brake system continues to function normally, but without the
functions listed above. The wheels could therefore lock if you
brake hard, for example.
The steerability and braking characteristics may be severely
affected. The braking distance in an emergency braking situation
can increase.
If ESP ®
is not operational, ESP ®
is unable to stabilize the vehicle.
There is an increased risk of skidding and an accident.
X Drive on carefully.
X Visit a qualified specialist workshop immediately. 19
Not available on hybrid vehicles. 392
Display messagesOn-board computer and displays

Display messages Possible causes/consequences and
0004 Solutions
000C
Currently
Unavailable See
Operator's Manual ESP
®
,B AS, PRE-SAFE ®
, the HOLD functio nand hill start assist are
temporarily unavailable.
BAS PLUS and PRE-SAFE ®
Brake may also have failed.
In addition, the 000Cand0013 warning lamps light up in the
instrument cluster.
The self-diagnosis functio nmight not be complete, for example.
ATTENTION ASSIST 19
is deactivated.
G WARNING
The brake system continues to function normally, but without the
functions listed above.
The braking distance in an emergency braking situation can thus
increase.
If ESP ®
is not operational, ESP ®
is unable to stabilize the vehicle.
There is an increased risk of skidding and an accident.
X Carefully drive a shor tdistance on a suitable stretch of road,
making slight steering movements at a speed above 12 mph
(20 km/h).
If the display message disappears, the functions mentioned
above are available again.
If the display message continues to be displayed:
X Drive on carefully.
X Visit a qualified specialist workshop. G
WARNING
If the display message is shown and the 000Cwarning lamp flashes
at the same time, the Electronic Traction System is deactivated.
Otherwise, the brakes on the drive wheels could overheat.
X Let the brakes cool down until the display message disappears
and the 000Cwarning lamp goes out.
The Electronic Traction System is activated again. 19
Not available on hybrid vehicles. Display messages
393On-board computer and displays Z

Display messages Possible causes/consequences and
0004 Solutions
000C
Inoperative See
Operator's Manual ESP
®
,B AS, PRE-SAFE ®
, the HOLD functio nand hill start assist are
unavailable due to a malfunction.
BAS PLUS and PRE-SAFE ®
Brake may also have failed.
In addition, the 000Cand0013 warning lamps light up in the
instrument cluster.
The self-diagnosis functio nmight not be complete, for example.
ATTENTION ASSIST 19
is deactivated.
G WARNING
The brake system continues to function normally, but without the
functions listed above.
The braking distance in an emergency braking situation can thus
increase.
If ESP ®
is not operational, ESP ®
is unable to stabilize the vehicle.
There is an increased risk of skidding and an accident.
X Drive on carefully.
X Visit a qualified specialist workshop. 0013
System Inoperative G
WARNING
ESP ®
,B AS, PRE-SAFE ®
, the HOLD functio nand hill start assist are
unavailable due to a malfunction. BAS PLU Sand PRE-SAFE ®
Brake
may also have failed .Inaddition, the 000Cand0013 warning
lamps light up in the instrument cluster.
ATTENTION ASSIST 19
is deactivated.
X Drive on carefully.
X Visit a qualified specialist workshop. 19
Not available on hybrid vehicles. 394
Display messagesOn-board computer and displays