2013 MAZDA MODEL 2 lock

Black plate (265,1)
qReplacing Windshield Wiper Blades
When the wipers no longer clean well, the
blades are probably worn or cracked.
Replace them.
CAUTION
To prevent damage to the wiper arms
and other components, don't try to
sweep the wiper arm by hand.
1. Raise the wiper arm and turn the blade assembly to expose the plastic locking
clip.
Compress the clip and slide the
assembly downward; then lift it off the
arm.
Plastic locking clip
CAUTION
To prevent damage to the windshield
let the wiper arm down easily, don't
let it slap down on the windshield. 2. Hold the end of the rubber and pull
until the tabs are free of the metal
support.
Metal support
Ta b
3. Remove the metal stiffeners from each blade rubber and install them in the
new blade.
Maintenance and Care
Owner Maintenance
8-21
Mazda2_8CL7-EA-12H_Edition3 Page265
Friday, January 11 2013 9:50 AM
Form No.8CL7-EA-12H

Black plate (266,1)
CAUTION
ØDon't bend or discard the
stiffeners. You need to use them
again.
Ø If the metal stiffeners are
switched, the blade's wiping
efficiency could be reduced.
So don't use the driver's side metal
stiffeners on the passenger's side,
or vice versa.
Ø Be sure to reinstall the metal
stiffeners in the new blade rubber
so that the curve is the same as it
was in the old blade rubber.
4. Carefully insert the new blade rubber. Then install the blade assembly in the
reverse order of removal.
NOTE
Install the blade so that the tabs are toward the
bottom of the wiper arm.
qReplacing Rear Window Wiper
Blade
When the wiper no longer cleans well, the
blade is probably worn or cracked.
Replace it.
CAUTION
To prevent damage to the wiper arm
and other components, do not try to
sweep the wiper arm by hand.
1. Raise the wiper arm.
NOTE
The wiper arm will not remain lifted off the
rear window after being pulled up.
When replacing the wiper blade, continue
holding the wiper arm with one hand during
the work.
2. Firmly rotate the wiper blade to the right until it unlocks, then remove the
blade.
8-22
Maintenance and Care
Owner Maintenance
Mazda2_8CL7-EA-12H_Edition3 Page266
Friday, January 11 2013 9:50 AM
Form No.8CL7-EA-12H

Black plate (277,1)
WARNING
Never touch the glass portion of a
halogen bulb with your bare hands and
always wear eye protection when
handling or working around the bulbs:When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurized gas. If one is broken, it
will explode and serious injuries
could be caused by the flying glass.
If the glass portion is touched with
bare hands, body oil could cause the
bulb to overheat and explode when
lit.
Always keep halogen bulbs out of the
reach of children: Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb
or breaking it some other way.
qReplacing Exterior Light Bulbs
Headlight bulbs
1. Make sure the headlight switch is off.
2. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the left, and turn off the
engine. If you are changing the left
bulb, turn the steering wheel to the
right. 3. Turn the screws and the center section
of the plastic retainers
counterclockwise and remove them,
then partially peel back the mudguard.
Removal
Installation
4. Detach the electrical connector from the sealing cover by pulling it to the
rear.
Maintenance and Care
Owner Maintenance
8-33
Mazda2_8CL7-EA-12H_Edition3 Page277
Friday, January 11 2013 9:50 AM
Form No.8CL7-EA-12H

Black plate (278,1)
5. Detach the sealing cover from the bulb.
Sealing cover
6. Unhook the bulb retaining spring.
7. Swing the retaining spring out andaway to free the headlight bulb.
8. Carefully remove the headlight bulb
from the socket by pulling it straight
back.
9. Replace the bulb.
10. Install the new bulb in the reverse order of removal.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton of the
replacement bulb to dispose of the old bulb
promptly out of the reach of children.
lWhen reinstalling the sealing cover, make
sure it fitted correctly.
Fog light bulbsí
1. Make sure the ignition is switched off, and the headlight switch is off.
2. Turn the screw counterclockwise and remove it, then partially peel back the
mudguard.
8-34
Maintenance and Care
íSome models.
Owner Maintenance
Mazda2_8CL7-EA-12H_Edition3 Page278
Friday, January 11 2013 9:50 AM
Form No.8CL7-EA-12H

Black plate (279,1)
3. Disconnect the electrical connectorfrom the bulb by pressing the tab on
the connector with your finger and
pulling the connector.
4. Turn the bulb assemblycounterclockwise and remove it.
5. Install the new bulb in the reverse order
of removal.
NOTE
lTo replace the bulb, contact an Authorized
Mazda Dealer.
lIf the halogen bulb is accidentally touched,
it should be cleaned with rubbing alcohol
before being used.
lUse the protective cover and carton of the
replacement bulb to dispose of the old bulb
promptly out of the reach of children.
Front turn signal lights
1. Make sure the ignition is switched off and the headlight switch is off.
2. Lift the hood.
3. Turn the socket and bulb assembly counterclockwise and remove it.
4. Remove the bulb by pushing it in slightly and turning it
counterclockwise.
5. Install the new bulb in the reverse orderof removal.
Parking lights/Front side-marker lights
1. Make sure the headlight switch is off.
2. If you are changing the right bulb, startthe engine, turn the steering wheel all
the way to the left, and turn off the
engine. If you are changing the left
bulb, turn the steering wheel to the
right.
Maintenance and Care
Owner Maintenance
8-35
Mazda2_8CL7-EA-12H_Edition3 Page279
Friday, January 11 2013 9:50 AM
Form No.8CL7-EA-12H

Black plate (280,1)
3. Turn the screws and the center sectionof the plastic retainers
counterclockwise and remove them,
then partially peel back the mudguard.
Removal
Installation
4. Turn the socket and bulb assembly counterclockwise and remove it.
5. Disconnect the bulb from the socket.
6. Install the new bulb in the reverse order of removal.
Side turn signal lights
1. Make sure the ignition is switched offand the headlight switch is off.
2. Slide the unit as shown in the figure to remove it.
3. Detach the electrical connector fromthe unit by pulling it outward.
4. Install the new side turn signal unit inthe reverse order of removal.
NOTE
Bulb replacement is not possible because it is
built into the unit. Replace the unit.
8-36
Maintenance and Care
Owner Maintenance
Mazda2_8CL7-EA-12H_Edition3 Page280
Friday, January 11 2013 9:50 AM
Form No.8CL7-EA-12H

Black plate (281,1)
Brake lights/Taillights (Rear side
marker lights)/Rear turn signal lights/
Reverse lights
1. Make sure the ignition is switched offand the headlight switch is off.
2. Turn the bolts counterclockwise and remove them.
3. Pull the unit rearward to remove it.
4. Turn the socket and bulb assemblycounterclockwise and remove it.
5. Disconnect the bulb from the socket. Brake lights/Taillights (Rear side
marker lights)
Rear turn signal lights
Reverse lights
6. Install the new bulb in the reverse order
of removal.
Maintenance and Care
Owner Maintenance
8-37
Mazda2_8CL7-EA-12H_Edition3 Page281
Friday, January 11 2013 9:50 AM
Form No.8CL7-EA-12H

Black plate (284,1)
3. Pull the fuse straight out with the fusepuller provided on the inside of the
engine compartment fuse block cover.
Fuse block (Engine compartment)
4. Inspect the fuse and replace it if it'sblown.
Normal Blown
5. Insert a new fuse of the same amperage
rating, and make sure it fits tightly. If it
does not fit tightly, have an expert
install it. We recommend an
Authorized Mazda Dealer.
If you have no spare fuses, borrow one
of the same rating from a circuit not
essential to vehicle operation, such as
the MIRROR or CIGAR circuit.
CAUTION
Always replace a fuse with one of the
same rating. Otherwise you may
damage the electric system. 6. Reinstall the cover and make sure that
it is securely installed.
Replacing the fuses under the hood
If the headlights or other electrical
components do not work and the fuses in
the cabin are normal, inspect the fuse
block under the hood. If a fuse is blown, it
must be replaced. Follow these steps:
1. Make sure the ignition is switched off,
and other switches are off.
2. Remove the fuse block cover.
3. If any fuse but the MAIN fuse is blown, replace it with a new one of the
same amperage rating .
Normal
Blown
8-40
Maintenance and Care
Owner Maintenance
Mazda2_8CL7-EA-12H_Edition3 Page284
Friday, January 11 2013 9:50 AM
Form No.8CL7-EA-12H