2013 Lexus IS300h maintenance

4807-3. Do-it-yourself maintenance
IS300h_EE(OM53B95E)
Vehicles with LED headlights
Rear
Halogen front fog light (if equipped)
Front turn signal light1
2
Back-up light (right-hand drive vehicles)
Back-up light (left-hand drive vehicles)
Rear turn signal light
Outer foot light1
2
3
4

4817-3. Do-it-yourself maintenance
7
Maintenance and care
IS300h_EE(OM53B95E)
Halogen front fog lights (if equipped)
Remove the 2 fender liner
screws under the front fog
light and pull back the fender
liner.
Unplug the connector while
pressing the lock release.
Turn the bulb base counter-
clockwise.
Set the new light bulb.
Hold the bulb base at an
angle of about 45 degrees as
shown in the illustration and
insert it so that the 3 tabs on
the light bulb are aligned
with the mounting.
Turn the light bulb clock-
wise to install it.
Replacing light bulbs
1
2
3
4
1
2

4827-3. Do-it-yourself maintenance
IS300h_EE(OM53B95E)
Set the connector.
After installing the connector,
shake the bulb base gently to
check that it is not loose, turn the
fog lights on once and visually
confirm that no light is leaking
through the mounting.
Reinstall the fender liner with
the 2 screws.
5
6

4837-3. Do-it-yourself maintenance
7
Maintenance and care
IS300h_EE(OM53B95E)
Front turn signal lights (vehicles with discharge headlights)
To ensure enough space to per-
form work, turn the steering
wheel to rotate the front wheel
away from the bulb to be
replaced.
Remove the 2 fender liner
clips.
Turn the steering wheel to the left
when replacing the right side light
bulb, and turn the steering wheel
to the right when replacing the
left side light bulb.
To take out the lower clip, turn
the head of the clip to unlock it,
then remove it by pulling.
Unfasten the clamp, and pull
back the fender liner.
When unfastening the clamp,
wrap the tip of the screwdriver
with tape to protect the vehicle
from damage.
Turn the bulb base counter-
clockwise.
1
2
3

4847-3. Do-it-yourself maintenance
IS300h_EE(OM53B95E)
Remove the light bulb.
Install a new light bulb then
install the bulb base to the
light unit by inserting it and
turning the bulb base clock-
wise.
After installing the light bulb,
turn on the front turn signal light
to visually check that there is no
light leaking from the bulb base.
Reinstall the fender liner, fas-
ten the clamp and install the 2
clips.
Install the lower clip by inserting
it with the clip groove held verti-
cally straight.
4
5
6

4857-3. Do-it-yourself maintenance
7
Maintenance and care
IS300h_EE(OM53B95E)
Front turn signal lights (vehicles with LED headlights)
For the left side only: Pinch
the clip to remove the washer
fluid filler opening.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
Install a new light bulb then
install the bulb base to the
light unit by inserting it and
turning the bulb base clock-
wise.
After installing the light bulb,
turn on the front turn signal light
to visually check that there is no
light leaking from the bulb base.
After replacing the left side bulb, install the washer fluid filler open-
ing to its original position.
1
2
3
4
5

4867-3. Do-it-yourself maintenance
IS300h_EE(OM53B95E)
Rear turn signal lights
Open the trunk, and remove
the 2 covers and 2 screws.
When removing the cover, wrap
the tip of the screwdriver with
tape to protect the vehicle from
damage.
Push and pull the light unit
toward the rear of the vehicle
as shown in the illustration to
remove it.
Apply protective tape to the
peripheral of the light unit instal-
lation surface on the vehicle body,
such as the rear bumper, to protect
the vehicle from damage.
Pushing on the portion A in the
illustration toward the rear of the
vehicle will make disengagement
of the tabs easier.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
1
2
3
4

4877-3. Do-it-yourself maintenance
7
Maintenance and care
IS300h_EE(OM53B95E)
Install a new light bulb then
install the bulb base to the
light unit by inserting it and
turning the bulb base clock-
wise.
After installing the light bulb,
turn on the rear turn signal light to
visually check that there is no
light leaking from the bulb base.
Align the tabs and push the
light unit toward the front of
the vehicle to install it.
Remove the protective tape
applied to the peripheral of the
light unit installation surface on
the vehicle body.
Install the 2 screws and 2 covers.
5
6
7