2013 Lexus GS450h warning light

GS450h_U (OM30D01U)
852. Instrument cluster
2
Instrument cluster
Warning lights inform the driver of malfunctions in the indicated vehicle’s
systems.
Warning lights
*1
(U.S.A.)
Brake system warning light
(  P. 711)*1, 2
(if equipped)
“AFS OFF” indicator
( P. 7 1 3 )
*1
(Canada)
Brake system warning light
( P. 711)*1, 2Brake hold operated
indicator ( P. 7 1 3 )
*1Charging system warning
light ( P. 7 1 2 )*2
(U.S.A.)
Parking brake indicator
( P. 7 1 3 )
*1
(U.S.A.)
Malfunction indicator
lamp ( P. 7 1 2 )*2
(Canada)
Parking brake indicator
( P. 7 1 3 )
*1
(Canada)
Malfunction indicator
lamp ( P. 7 1 2 )*1Brake system warning light
( P. 7 1 4 )
*1SRS warning light
( P. 7 1 2 )Open door warning light
( P. 7 1 4 )
*1
(U.S.A.)
ABS warning light
( P. 7 1 2 )Low fuel level warning light
( P. 7 1 4 )
*1
(Canada)
ABS warning light
( P. 7 1 2 )Seat belt reminder light
( P. 7 1 4 )
*1Electric power steering
system warning light
( P. 7 1 2 )*1Master warning light
( P. 7 1 4 )

86
GS450h_U (OM30D01U)
2. Instrument cluster
*1: These lights turn on when the power switch is turned to ON mode to indicate that
a system check is being performed. They will turn off after the hybrid system is on,
or after a few seconds. There may be a ma lfunction in a system if the lights do not
come on, or turn off. Have the vehicle inspected by your Lexus dealer.
*2: The light flashes to indicate a malfunction.
*1, 2
(if equipped)
“PCS” warning light
(  P. 7 1 2 , 7 2 6 )*1
Tire pressure warning light
( P. 7 1 5 )
*1
Slip indicator ( P. 7 1 3 )

GS450h_U (OM30D01U)
872. Instrument cluster
2
Instrument cluster
The indicators inform the driver of the operating state of the vehicle’s vari-
ous systems.
Indicators
Turn signal indicator
(  P. 205)
(if equipped)
LKA (Lane-Keeping
Assist) indicator
( P. 2 5 1 )
(U.S.A.)
Headlight indicator
( P. 2 1 3 )

(if equipped)
Intuitive parking assist indi-
cator ( P. 2 6 1 )
(Canada)
Tail light indicator
( P. 2 1 3 ) *1
(if equipped)
“AFS OFF” indicator
( P. 215)
Headlight high beam indi-
cator ( P. 2 1 4 )
*1, 2 Slip indicator
( P. 2 9 1 )
(if equipped)
Front fog light indicator
( P. 2 1 8 )*1VSC OFF indicator
( P. 2 9 1 )
“READY” indicator
(  P. 1 8 9 )
*1, 3
(if equipped)
“PCS” warning light
( P. 2 9 7 )
EV indicator ( P. 7 2 )
(U.S.A.)
Parking brake indicator
( P. 2 0 7 )
Cruise control indicator
(  P. 232, 236)
(Canada)
Parking brake indicator
( P. 2 0 7 )
(if equipped)
Radar cruise control indi-
cator ( P. 2 3 6 )*1Brake hold standby indica-
tor ( P. 2 1 0 )
Cruise control “SET” indi-
cator ( P. 232, 236)
*1Brake hold operated indi-
cator ( P. 2 1 0 )
*1“A I R B A G O N /
OFF” indicator
( P. 4 9 )

88
GS450h_U (OM30D01U)
2. Instrument cluster
*1: These lights turn on when the power switch is turned to ON mode to indicate that
a system check is being performed. They will turn off after the hybrid system is on,
or after a few seconds. There may be a ma lfunction in a system if the lights do not
come on, or turn off. Have the vehicle inspected by your Lexus dealer.
*2: The light flashes to indicate that the system is operating.
*3: The light comes on when the system is turned off. The light flashes faster than
usual to indicate that the system is operating.
CAUTION
■If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning light not come on
when you start the hybrid system, this co uld mean that these systems are not avail-
able to help protect you in an accident, wh ich could result in death or serious injury.
Have the vehicle inspected by your Lexus dealer immediately if this occurs.

100
GS450h_U (OM30D01U)
2. Instrument cluster
■System check display
After turning the power switch to ON mode, “SYSTEM CHECK” is displayed while
system operation is checked.
■Outside temperature display
In the following situations, the correct outside temperature may not be displayed, or
the display may take longer than normal to change.
●When stopped, or driving at low speeds (less than 12 mph [20 km/h])
●When the outside temperature has changed suddenly (at the entrance/exit of a
garage, tunnel, etc.)
■Setting display automatic cancelation
In the following situations, setting display in which the settings can be changed
through the “DISP” button will automatically be turned off.
●When a warning message appears whil e the setting display is displayed
●When the vehicle begins to move while the setting display is displayed
■Tire inflation pressure (if equipped)
●It may take a few minutes to display the ti re inflation pressure after the power switch
is turned to ON mode. It may also take a few minutes to display the tire inflation
pressure after inflation pr essure has been adjusted.
●“---” may be displayed if the tire information cannot be determined due to unfavor-
able radio wave conditions.
●Tire inflation pressure changes with temperature. The displayed values may also be
different from the values measured using a tire pressure gauge.
■Liquid crystal display
Small spots or light spots may appear on th e display. This phenomenon is character-
istic of liquid crystal displays, and there is no problem continuing to use the display.
■Customization
Setting of available languages can be changed. (Custo mizable features P. 8 0 7 )

GS450h_U (OM30D01U)
2094-2. Driving procedures
4
Driving
■When there is a malfunction in the system
Warning lights and/or warning message will turn on or flash. (P. 7 1 3 , 7 2 6 )
Depending on the condition, the parking brake indicator light may flash.
■Usage in winter time
 P. 3 2 0
NOTICE
■When parking the vehicle
Before you leave the vehicle, set the parking brake, shift the shift lever to P and
make sure that the vehicle does not move.
■When the system malfunctions
Stop the vehicle in a safe place and check the warning messages.
■When the parking brake cannot be released due to a malfunction
Use the parking brake release tool to manually release the parking brake.
( P. 765)
Driving the vehicle with the parking brake set will lead to brake components over-
heating, which may affect braking performance and increase brake wear.

210
GS450h_U (OM30D01U)
4-2. Driving procedures
Brake Hold
Turns the brake hold system on
The brake hold standby indicator
(green) comes on. While the system is
holding the brake, the brake hold
operated indicator (yellow) comes on.
■Brake hold system operating conditions
The brake hold system cannot be turn ed on in the following conditions:
●The trunk or hood is not closed.
●The driver’s door is not closed.
●The driver is not wearing the seat belt.
If any of the conditions above are detected when the brake hold system is enabled,
the system will turn off and the brake hold standby indicator light will go off. In addi-
tion, if any of the conditions are detected while the system is holding the brake, a
warning buzzer will sound and a message wi ll be shown on the multi-information dis-
play. The parking brake will then be set automatically.
■Brake hold function
●If the brake pedal is left released for a period of about 3 minutes after the system
has started holding the brake, the parking brake will be set automatically. In this
case, a warning buzzer sounds and a message is shown on the multi-information
display.
●To turn the system off while the system is holding the brake, firmly depress the
brake pedal and press the button again.
●The brake hold function may not hold the vehicle when the vehicle is on a steep
incline. In this situation, it may be nece ssary for the driver to apply the brakes. The
multi-information display will info rm the driver of this situation.
The brake hold system keeps the brake applied when the shift lever is in
D, S or N with the system on and the brake pedal has been depressed to
stop the vehicle. The system releases the brake when the accelerator
pedal is depressed with the shift lever in D or S to allow smooth start off.

GS450h_U (OM30D01U)
2114-2. Driving procedures
4
Driving
■When the parking brake is set automatically while the system is holding the brakes
The parking brake will not be released automatically. Release the parking brake by
operating the parking brake switch, making sure that the parking brake indicator
light goes off. ( P. 2 0 7 )
■When there is a malfunction in the system
Warning lights and/or warning mess ages will turn on or flash. (P. 713, 725)
CAUTION
■When the vehicle is on a steep incline
When using the brake hold system on a steep incline exercise caution. The brake
hold function may not hold th e vehicle in such a situation.
■When stopped on a slippery road
The system cannot stop the vehicle when the gripping ability of the tires has been
exceeded. Do not use the system wh en stopped on a slippery road.
NOTICE
■When parking the vehicle
The brake hold system is not designed for use when parking the vehicle for a long
period of time. Turning the power switch off while the system is holding the brake
may release the brake, which would cause the vehicle to move. When operating
the power switch, depress the brake pedal, set the parking brake and shift the shift
lever to P.