2013 Lexus CT200h rear view mirror

163
3 3-3. Adjusting the seats
Operation of each component
CT200h_OM_OM76102E_(EE)
Driving position memory
Your preferred driving position (the position of the driver’s seat and out-
side rear view mirrors) can be recorded and recalled by pressing a button.
Three different driving positions can be recorded into memory.
Recording procedure
Turn the power switch to ON mode.
Check that the shift position is in P.
Adjust the driver’s seat and outside rear view mirrors to the desired
positions.
While pressing the “SET” but-
ton, or within 3 seconds after
the “SET” button is pressed,
press button “1”, “2” or “3”
until the buzzer sounds.
If the selected button has already
been preset, the previously
recorded position will be over-
written.
: If equipped
This feature automatically adjusts the driver’s seat and outside rear view
mirrors to suit your preferences.
Driving position memory
1
2
3
4

1653-3. Adjusting the seats
3
Operation of each component
CT200h_OM_OM76102E_(EE)
Each electronic key (including a card key) can be registered to recall your
preferred driving position.
Registering procedure
Record your driving position to button “1”, “2” or “3” before perform-
ing the following:
Carry only the key you want to register, and then close the driver’s
door.
If 2 or more keys are in the vehicle, the driving position cannot be
recorded properly.
Turn the power switch to ON mode.
Check that the shift position is in P.
Recall the driving position that you want to record.
While pressing the recalled
button, press and hold the door
lock switch (either lock or
unlock) until the buzzer
sounds.
If the button could not be regis-
tered, the buzzer sounds continu-
ously for approximately 3
seconds.
Recall procedure
Carry the electronic key that has been registered to the driving posi-
tion, and then unlock and open the driver’s door using the smart entry
& start system or wireless remote control.
The driving position will move to the recorded position.
If the driving position is in a position that has already been recorded, the
seat and outside rear view mirrors will not move.
Memory recall function
1
2
3
4

1723-4. Adjusting the steering wheels and mirrors
CT200h_OM_OM76102E_(EE)
Inside rear view mirror
The height of the rear view mirror can be adjusted to suit your driving
posture.
Adjust the height of the rear view
mirror by moving it up and down.
Manual anti-glare inside rear view mirror
Normal position
Anti-glare position
The rear view mirror’s position can be adjusted to enable sufficient con-
firmation of the rear view.
Adjusting the height of rear view mirror
Anti-glare function
1
2

1733-4. Adjusting the steering wheels and mirrors
3
Operation of each component
CT200h_OM_OM76102E_(EE)
Auto anti-glare inside rear view mirror
Responding to the level of brightness of the headlights of vehicles behind,
the reflected light is automatically reduced.
Changing automatic anti-glare
function mode
On/off
When the automatic anti-glare func-
tion is in ON mode, the indicator
illuminates.
The function will set to ON mode
each time the power switch is turned
to ON mode.
Pressing the button turns the func-
tion to OFF mode. (The indicator
also turns off.)
To prevent sensor error (vehicles with auto anti-glare inside rear view mirror)
Indicator
To ensure that the sensors operate properly,
do not touch or cover them.
WA R N I N G
Do not adjust the position of the mirror while driving.
Doing so may lead to mishandling of the vehicle and cause an accident, result-
ing in death or serious injury.

1743-4. Adjusting the steering wheels and mirrors
CT200h_OM_OM76102E_(EE)
Outside rear view mirrors
Ty p e A
To select a mirror to adjust, press
the switch.
Left
Right
To adjust the mirror, press the
switch.
Up
Right
Down
Left
Ty p e B
To select a mirror to adjust, slide
the switch.
Left
Right
Adjustment procedure
1
1
2
2
1
2
3
4
1
1
2

1753-4. Adjusting the steering wheels and mirrors
3
Operation of each component
CT200h_OM_OM76102E_(EE)
To adjust the mirror, press the
switch.
Up
Right
Down
Left
Ty p e A
Press the switch to fold the mirrors.
Press it again to extend them to the
original position.
Ty p e B
Extends the mirrors
Folds the mirrors
Putting the outside rear view mirror
folding switch in the neutral position
sets the mirrors to automatic mode.
Automatic mode allows the folding
or extending of the mirrors to be
linked to locking/unlocking of the
doors.
2
1
2
3
4
Folding and extending the mirrors
1
2

1763-4. Adjusting the steering wheels and mirrors
CT200h_OM_OM76102E_(EE)
Mirror angle can be adjusted when
The power switch is in ACCESSORY or ON mode.
Linked mirror function when reversing (type B only)
When the mirror select switch is in the “L” or “R” position, the outside rear view
mirrors will automatically angle downwards when the vehicle is reversing in
order to give a better view of the ground. To disable this function, move the mir-
ror select switch to the neutral position (between “L” and “R”).
Rain clearing mirrors (type B only)
The coating on the mirror has the rain clearing (hydrophilic) effect to make the
rear view clearer in raining. When water droplets collects on the mirror surface,
this effect causes the droplets to be spread out into a film.
The rain clearing effect will be reduced temporarily, when the dirt is adhered to
the mirror or after your vehicle is parked for a long time in underground or
indoor parking lots, etc., where there is no direct sunlight. However, the effect
will gradually recover after 1- or 2-day exposure to direct sunlight.
If you want to restore the rain clearing effect immediately, conduct the resto-
ration work (P. 481).
When the mirrors are fogged up
The outside rear view mirrors can be cleared using the mirror defoggers. Turn on
the rear window defogger to turn on the outside rear view mirror defoggers.
(P. 447, 454)
Automatic adjustment of the mirror angle (vehicles with driving position mem-
ory)
A desired mirror face angle can be entered to memory and recalled automatically
by the driving position memory. (P. 163)
Auto anti-glare function (type B only)
When the anti-glare inside rear view mirror is set to automatic mode, the outside
rear view mirrors will activate in conjunction with the anti-glare inside rear view
mirror to reduce reflected light. (P. 172)
Using automatic mode in cold weather (type B only)
When automatic mode is used in cold weather, the door mirror could freeze up
and automatic stowing and return may not be possible. In this event, remove any
ice and snow from the door mirror, then either operate the mirror using manual
mode or move the mirror by hand.
Customization
The automatic mirror folding and extending operation can be changed.
(Customizable features: P. 659)

1773-4. Adjusting the steering wheels and mirrors
3
Operation of each component
CT200h_OM_OM76102E_(EE)
WA R N I N G
When driving the vehicle
Observe the following precautions while driving.
Failing to do so may result in loss of control of the vehicle and cause an acci-
dent, resulting in death or serious injury.
Do not adjust the mirrors while driving.
Do not drive with the mirrors folded.
Both the driver and passenger side mirrors must be extended and properly
adjusted before driving.
When a mirror is moving
To avoid personal injury and mirror malfunction, be careful not to get your
hand caught by the moving mirror.
When the mirror defoggers are operating
Do not touch the rear view mirror surfaces, as they can become very hot and
burn you.
NOTICE
Handling the rain clearing mirror (type B only)
The rain clearing effect is finite. Observe the Following precautions in order to
retain the rain-clearing properties of the mirrors:
When using water repellent, oil film remover, wax, or any other car mainte-
nance product that contains silicone, pay full attention not to adhere it to the
mirror surface.
Do not wipe the mirror surface by using any cloth smeared with sand, oil film
remover, abrasive agent, or any other thing that may scratch the mirror sur-
face.
When the mirrors become iced up, remove the ice by applying warm water, or
operating the outside rear view mirror defoggers, etc. But, do not attempt to
scrape the ice off by using the plastic plate, etc.
When washing your vehicle using car shampoo with water repellent effect,
rinse the mirror surface with a lot of water, and remove the water drops by
using a clean and soft cloth.