2013 Lancia Thema lights

Towing Requirements – Tires
– Do not attempt to tow a trailerwhile using a compact spare tire.
– Proper tire inflation pressures are essential to the safe and satisfactory
operation of your vehicle. Refer to
“Tires – General Information” in
“Starting and Operating” for infor-
mation on tire pressures and for
proper tire inflation procedures.
–Check the trailer tires for proper tire
inflation pressures before trailer
usage.– Check for signs of tire wear or vis- ible tire damage before towing a
trailer. Refer to “Tires – General
Information” in “Starting and Op-
erating” for information on tread
wear indicators and for the proper
inspection procedure.
– When replacing tires, refer to “Tires – General Information” in “Start-
ing and Operating” for information
on replacement tires and for the
proper tire replacement proce-
dures. Replacing tires with a higher
load carrying capacity will not in-
crease the vehicle's GVWR and
GAWR limits. Towing Requirements – Trailer
Brakes
– Do
notinterconnect the hydraulic
brake system or vacuum system of
your vehicle with that of the trailer.
This could cause inadequate brak-
ing and possible personal injury.
–
An electronically actuated trailer
brake controller is required when
towing a trailer with electronically
actuated brakes. When towing a
trailer equipped with a hydraulic
surge actuated brake system, an
electronic brake controller is not
required.–Trailer brakes are recommended for
trailers over 454 kg and required for
trailers in excess of 907 kg.CAUTION!
If the trailer weighs more than
454 kg loaded, it should have its
own brakes, and they should be of
adequate capacity. Failure to do
this could lead to accelerated brake
wear, higher brake pedal effort, and
longer stopping distances.
WARNING!
 Do not connect trailer brakes to your vehicle's hydraulic brake
lines. It can overload your brake
system and cause it to fail. You
might not have brakes when you
need them and could have a col-
lision.
Towing any trailer will increase
your stopping distance. When
towing, you should allow for addi-
tional space between your vehicle
and the vehicle in front of you.
Failure to do so could result in a
collision.
Towing Requirements – Trailer
Lights And Wiring
Whenever you pull a trailer, regard-
less of the trailer size, stoplights and
turn signals on the trailer are required
for motoring safety.
The Trailer Tow Package may include
a 7-pin or a 13-pin wiring harness.
Use a factory approved trailer harness
and connector.
247

NOTE:
Do not cut or splice wir-
ing into the vehicles wiring harness.
The electrical connections are all com-
plete to the vehicle but you must mate
the harness to a trailer connector.
Pin
Number Function Wire
Color
1 Left Turn Signal Yellow
2 Rear Fog Light Blue
3 Ground/ Common
Return White
4 Right Turn Signal Green
Pin
Number Function Wire
Color
5 Right Rear Position,
Side Marker
Lights, and
Rear Regis-
tration Plate
Illumination
Device. b Brown
6 Stoplights Red
7 Left Rear Position,
Side Marker
Lights, and
Rear Regis-
tration Plate
Illumination
Device. b Black
b The rear position registration
plate illumination device shall be
connected such that no light of the
device has a common connection
with both pins 5 and 7.
Pin
Number Function Wire
Color
1 Left Turn Signal Yellow
2 Rear Fog Light Blue
3 a
Ground/
Common
Return for
Contacts
(Pins) 1 and 2
and 4 to 8
White
4 Right Turn Signal Green
7–Pin Connector
13–Pin Connector
248

Pin
Number Function Wire
Color
5 Right Rear Position,
Side Marker
Lights, and
Rear Regis-
tration Plate
Illumination
Device. b Brown
6 Stoplights Red
7 Left Rear Position,
Side Marker
Lights, and
Rear Regis-
tration Plate
Illumination
Device. b Black
8 Reverse lights Red/ Black
9
Permanent
Power Supply
(+12V)
Brown/
White
10
Power Supply
Controlled
by Ignition
Switch (+12V)
Red
Pin
Number Function Wire
Color
11 a Return for Contact
(Pin) 10 White
12 Reserve for Future Allo-
cation Red/
Blue
13 a Return for Contact
(Pin) 9 White
Note: The allocation pin 12 has
been changed from “Coding for
coupled Trailer” to “Reserve for
Future Allocation.”
a The three return circuits shall not
be connected electrically in the
trailer.
b The rear position registration
plate illumination device shall be
connected such that no light of the
device has a common connection
with both pins 5 and 7. TOWING TIPS
Before setting out on a trip, practice
turning, stopping, and backing up the
trailer in an area located away from
heavy traffic.
Automatic Transmission
The DRIVE range can be selected
when towing. The transmission con-
trols include an adaptive drive strat-
egy to avoid frequent shifting when
towing. However, if frequent shifting
does occur while in DRIVE, use
the AutoStick® shift control (for
versions/markets, where provided) to
manually select a lower gear.
NOTE: Selecting a lower gear
while operating the vehicle under
heavy loading conditions will im-
prove performance and extend
transmission life by reducing ex-
cessive shifting and heat buildup.
This action will also provide better
engine braking.
249

Cleaning Headlights
Your vehicle has plastic headlights
that are lighter and less susceptible to
stone breakage than glass headlights.Plastic is not as scratch resistant as
glass and therefore different lens clean-
ing procedures must be followed.To minimize the possibility of scratch-
ing the lenses and reducing light out-
put, avoid wiping with a dry cloth. To
remove road dirt, wash with a mild
soap solution followed by rinsing.Do not use abrasive cleaning compo-
nents, solvents, steel wool or other ag-
gressive material to clean the lenses.Glass Surfaces
All glass surfaces should be cleaned
on a regular basis with any commer-
cial household-type glass cleaner.
Never use an abrasive type cleaner.
Use caution when cleaning the inside
rear window equipped with an elec-
tric defroster. Do not use scrapers or
other sharp instruments that may
scratch the elements.When cleaning the rear view mirror,
spray cleaner on the towel or rag that
you are using. Do not spray cleaner
directly on the mirror.
Cleaning Plastic Instrument
Cluster Lenses
The lenses in front of the instruments
in this vehicle are molded in clear
plastic. When cleaning the lenses,
care must be taken to avoid scratch-
ing the plastic.
1. Clean with a wet soft rag. A mild
soap solution may be used, but do not
use high alcohol content or abrasive
cleaners. If soap is used, wipe clean
with a clean damp rag.
2. Dry with a soft cloth.
Seat Belt Maintenance
Do not bleach, dye, or clean the belts
with chemical solvents or abrasive
cleaners. This will weaken the fabric.
Sun damage can also weaken the fabric.If the belts need cleaning, use a mild
soap solution, or lukewarm water. Do
not remove the belts from the vehicle
to wash them.Replace the belts if they appear frayed
or worn or if the buckles do not work
properly.
Cleaning The Center Console
Cupholders
Clean with a damp cloth or towel using
a mild detergent with the cupholder in
the center console.NOTE: The cupholder cannot be
removed.
FUSES
Integrated Power ModuleThe Integrated Power Module is lo-
cated in the engine compartment. This
module contains fuses and relays.
Integrated Power Module
290

Exterior Bulb Number
Low Beam/High Beam
(Bi-Xenon Headlamp) . . . . D3S
(Serviced at Authorized Dealer)
Front Turn Signal
Lamp . . . . . . . . . . . PSY24WSV
Front Park Lamp . . . . . . . . LED(Serviced at Authorized Dealer)
Daytime Running Lamp . . . LED (Serviced at Authorized Dealer)
Front Fog Lamp
(for versions/markets,
where provided) . . . . . . . . . . H11
Front Position Lamp . . . . . . LED (Serviced at Authorized Dealer)
Front Side Marker Lamp . . . LED (Serviced at Authorized Dealer)
Side Repeater Lamps . . . . . . LED (Serviced at Authorized Dealer)
Rear Tail/Stop/Side Marker
Lamp . . . . . . . . . . . . . . . . . LED(Serviced at Authorized Dealer)
Rear Turn Signal Lamp . . WY21W
Rear Fog Lamps . . . . . . . . . . LED (Serviced at Authorized Dealer) Backup Lamp . . . . . . . . . . W16W
Center High Mount Stop
Lamp (CHMSL) . . . . . . . . . . LED
(Serviced at Authorized Dealer)
License . . . . . . . . . . . . . . . . W5W
BULB REPLACEMENT
LOW BEAM HEADLAMP,
HIGH BEAM HEADLAMP,
PARK/TURN LAMP, INNER
PARK LAMP, AND OUTER
PARK LAMP
High Intensity Discharge
Headlamps (HID)
(for versions/markets, where
provided)CAUTION!
Where possible, it is advisable to
have bulbs changed at a LANCIA
Dealership. Proper operation and
orientation of the external lights are
essential for driving safety and
complying with the law. The headlamps are a type of high
voltage discharge tube. High voltage
can remain in the circuit even with the
headlamp switch off and the key re-
moved.
Because of this, you should
not attempt to service a headlamp
bulb yourself. If a headlamp bulb
fails, take your vehicle to an au-
thorized dealer for service.
WARNING!
A transient high voltage occurs at
the bulb sockets of HID headlamps
when the headlamp switch is
turned ON. It may cause serious
electrical shock or electrocution if
not serviced properly. See your au-
thorized dealer for service.
NOTE: On vehicles equipped
with HID headlamps, when the
headlamps are turned on, there is
a blue hue to the lights. This di-
minishes and becomes more white
after approximately 10 seconds, as
the system charges.
299

Standard Low Beam Headlamp,
High Beam Headlamp, Park/Turn
Lamp, Inner Park Lamp, And
Outer Park LampCAUTION!
Where possible, it is advisable to
have bulbs changed at a LANCIA
Dealership. Proper operation and
orientation of the external lights are
essential for driving safety and
complying with the law.
1. Open the hood.
NOTE:
Removal of the air cleaner
filter housing may be necessary
prior to replacing bulbs in the head-
lamp assembly on the driver side of
the vehicle.
2. Twist the appropriate bulb and
socket assembly counterclockwise,
and then pull it out of the headlamp
assembly.
3.
Disconnect the bulb from the socket
assembly and install the replacement
bulb.
4. Reinstall the bulb and socket as-
sembly into the headlamp assembly,
and then turn it clockwise.CAUTION!
Do not touch the new bulb with
your fingers. Oil contamination will
severely shorten bulb life. If the
bulb comes in contact with an oily
surface, clean the bulb with rub-
bing alcohol.
FRONT TURN SIGNAL
LAMPS
1. Open the hood.
NOTE:
Removal of the air cleaner
filter housing may be necessary
prior to replacing bulbs in the head-
lamp assembly on the driver side of
the vehicle.
2. Remove plastic cap from the back
of the headlamp housing.
3. Squeeze the two tabs on the side of
the turn signal bulb socket and pull
straight out from the lamp. 4.
Install replacement bulb and con-
nector assembly straight into the lamp
until it locks in place.
5. Reinstall plastic cap to headlamp
assembly housing.
REAR TURN SIGNAL AND
BACKUP LAMPS
1. Open the trunk.
2.
Remove the trunk trim by removing
the grocery hook (using a T-20 torx
driver or similar tool), remove the fas-
tener, and pull back the weather strip.
3. Pull back the trunk liner to gain
access to the tail lamp wing nuts.
4. Remove the three wing nuts from
the back of the tail lamp assembly.
5. Pull the tail lamp assembly away
from the vehicle enough to access the
electrical connector.
6. Push the electrical connector lock-
ing tab to the side.
7.
Disconnect the electrical connector.
300

Thousands Of Kilometers 24 48 72 96 120 144 168 192Months 12 24 36 48 60 72 84 96
Inspect and replace PCV valve if necessary. 
Check battery charge status and possibly recharge.        
Check tire condition/wear and adjust pressure, if necessary.        
Check operation of lighting system (headlamps, direction
indicators, hazard warning lights, luggage compartment,
passenger compartment, glove compartment, instrument panel
warning lights, etc.).        
Check operation of windscreen washer system and adjust jets
if necessary.        
Check windshield/rear window wiper blade position/wear.        
Check cleanliness of hood and tailgate locks and cleanliness
and lubrication of linkages.        
Visually inspect condition of: exterior bodywork, underbody
protection, pipes and hoses (exhaust - fuel system - brakes),
rubber elements (boots, sleeves, bushes, etc.).        
Check conditions and wear of front disc brake pads.        
Check conditions and wear of rear disc brake pads.        
Check and, if necessary, top up fluid levels
(brakes, windshield washer, battery, engine coolant, etc.).        
Visually inspect the condition of accessory drive belt/s. 
Adjust parking brake shoes as necessary. 
Check exhaust gas emissions.        
311

Periodic Checks
Every1,000 km or before long jour-
neys, check and, if necessary, restore:
 engine coolant;
 brake fluid;
 Power Steering Fluid;
 windshield washer fluid level;
 power steering fluid;
tire inflation pressure and condition; operation of lighting system (head- lights, direction indicators, hazard
warning lights, etc.);
 operation of windshield washer/ wiper system and positioning/wear
of windshield/rear window wiper
blades.
Every 3,000 km, check and top up, if
required, the engine oil level. Heavy-Duty Use Of The Car
If the car is used mainly under one of
the following conditions:
 towing a trailer or caravan;
 dusty roads;
 short, repeated journeys (less than
7-8 km) at sub-zero outside
temperatures;
 engine often idling or driving long distances at low speeds or long pe-
riods of idleness.
You should perform the following in-
spections more frequently than shown
on the Scheduled Servicing Plan:
 check front disc brake pad condi- tions and wear;
 check cleanliness of hood and trunk locks, cleanliness and lubrication of
linkage;  visually inspect conditions of: en-
gine, transmission, pipes and hoses
(exhaust - fuel system - brakes) and
rubber elements (boots - sleeves -
bushes - etc.);
 check battery charge and battery fluid level (electrolyte);
 visually inspect condition of the accessory drive belts;
 check and, if necessary, change engine oil and replace oil filter;
 check and, if necessary, replace pol- len filter;
 check and, if necessary, replace air cleaner filter.
313