2013 Lancia Flavia lock

ANTI-LOCK BRAKE
SYSTEM (ABS)
This system aids the driver in main-
taining vehicle control under adverse
braking conditions. The system con-
trols hydraulic brake pressure to pre-
vent wheel lock-up and help avoid
skidding on slippery surfaces during
braking. Refer to “Anti-Lock Brake
System” in “Starting and Operating”
for further information.
TRACTION CONTROL
SYSTEM (TCS)
This system monitors the amount of
wheel spin of each of the driven
wheels. If wheel spin is detected,
brake pressure is applied to the slip-
ping wheel(s) and engine power is
reduced to provide enhanced accel-
eration and stability. A feature of the
TCS system functions similar to a lim-
ited slip differential and controls the
wheel spin across a driven axle. If one
wheel on a driven axle is spinning
faster than the other, the system will
apply the brake of the spinning wheel.
This will allow more engine torque tobe applied to the wheel that is not
spinning. This feature remains active
even if TCS and ESC are in the “Par-
tial Off” mode. Refer to “Electronic
Stability Control (ESC)” in this sec-
tion of this manual.
BRAKE ASSIST SYSTEM
(BAS)The BAS is designed to optimize the
vehicle’s braking capability during
emergency braking maneuvers. The
system detects an emergency braking
situation by sensing the rate and
amount of brake application and then
applies optimum pressure to the
brakes. This can help reduce braking
distances. The BAS complements the
Anti-Lock Brake System (ABS). Ap-
plying the brakes very quickly results
in the best BAS assistance. To receive
the benefit of the system, you must
apply continuous braking pressure
during the stopping sequence. Do not
reduce brake pedal pressure unless
braking is no longer desired. Once the
brake pedal is released, the BAS is
deactivated.
WARNING!
 The BAS cannot prevent the
natural laws of physics from act-
ing on the vehicle, nor can it in-
crease braking efficiency beyond
that afforded by the condition of
the vehicle brakes and tires or the
traction afforded.
The BAS cannot prevent collisions,
including those resulting from ex-
cessive speed in turns, following
another vehicle too closely, or hy-
droplaning.The capabilities of a BAS-equipped
vehicle must never be exploited in a
reckless or dangerous manner,
which could jeopardize the user’s
safety or the safety of others.
ELECTRONIC STABILITY
CONTROL (ESC)
This system enhances directional con-
trol and stability of the vehicle under
various driving conditions. ESC cor-
rects for over/under steering of the
vehicle by applying the brake of the
appropriate wheel to assist in counter-
acting the over/under steer condition.
154

NOTE: If the tire becomes over-
inflated, press the Deflation But-
ton to reduce the tire pressure to
the recommended inflation pres-
sure before continuing.
2. Disconnect the TIREFIT kit from
the valve stem, reinstall the cap on the
valve stem and unplug from 12 Volt
outlet.
3. Place the TIREFIT kit in its proper
storage area in the vehicle.
4. Have the tire inspected and re-
paired or replaced at the earliest op-
portunity at an authorized dealer or
tire service center.
5. Replace the Sealant Bottle (1) and
Sealant Hose (6) assembly at your
authorized dealer as soon as possible.
Refer to “(F) Sealant Bottle and Hose
Replacement.”
NOTE: When having the tire ser-
viced, advise the authorized dealer
or service center that the tire has
been sealed using the TIREFIT
service kit.(F) Sealant Bottle And Hose
Replacement:
1. Uncoil the Sealant Hose (6) (clear
in color).
2. Locate the round Sealant Bottle
release button in the recessed area
under the sealant bottle.
3. Press the Sealant Bottle release
button. The Sealant Bottle (1) will
pop up. Remove the bottle and dis-
pose of it accordingly.
4. Clean any remaining sealant from
the TIREFIT housing.
5. Position the new Sealant Bottle (1)
in the housing so that the Sealant
Hose (6) aligns with the hose slot in
the front of the housing. Press the
bottle into the housing. An audible
click will be heard indicating the
bottle is locked into place.
6. Verify that the cap is installed on
the fitting at the end of the Sealant
Hose (6) and return the hose to its
storage area (located on the bottom of
the air pump).
7. Return the TIREFIT kit to its stor-
age location in the vehicle.JUMP-STARTING
If your vehicle has a discharged bat-
tery it can be jump-started using a set
of jumper cables and a battery in an-
other vehicle or by using a portable
battery booster pack. Jump-starting
can be dangerous if done improperly
so please follow the procedures in this
section carefully.
NOTE: When using a portable
battery booster pack follow the
manufacturer's operating instruc-
tions and precautions.
CAUTION!
Do not use a portable battery
booster pack or any other booster
source with a system voltage
greater than 12 Volts or damage to
the battery, starter motor, alterna-
tor or electrical system may occur.WARNING!
Do not attempt jump-starting if the
battery is frozen. It could rupture or
explode and cause personal injury.
179

PREPARATIONS FOR
JUMP-START
The battery in your vehicle is located
between the left front headlight as-
sembly and the left front wheel splash
shield. To allow jump-starting there
are remote battery posts located on
the left side of the engine compart-
ment.
WARNING!
 Take care to avoid the radiatorcooling fan whenever the hood is
raised. It can start anytime the
ignition switch is ON. You can be
injured by moving fan blades.
 Remove any metal jewelry such
as watch bands or bracelets that
might make an inadvertent elec-
trical contact. You could be seri-
ously injured.
 Batteries contain sulfuric acid that can burn your skin or eyes
and generate hydrogen gas which
is flammable and explosive. Keep
open flames or sparks away from
the battery.
1. Set the parking brake, shift the
automatic transmission into PARK
and turn the ignition to LOCK.
2. Turn off the heater, radio, and all
unnecessary electrical accessories. 3. Remove the protective cover over
the remote positive
(+)battery post.
To remove the cover, press the locking
tab and pull upward on the cover.
4. If using another vehicle to jump-
start the battery, park the vehicle
within the jumper cables reach, set
the parking brake and make sure the
ignition is OFF.
WARNING!
Do not allow vehicles to touch each
other as this could establish a
ground connection and personal in-
jury could result.
Remote Battery Posts
1 — Remote Positive (+)Post
(covered with protective cap)
2 — Remote Negative (-)Post
Locking Tab
180

AUTOMATIC
TRANSMISSION
The manufacturer recommends tow-
ing your vehicle with all four wheels
OFF the ground using a flatbed.
If flatbed equipment is not available,
and the transmission is operable, the
vehicle may be flat towed (with all
four wheels on the ground) under the
following conditions:
 The transmission must be in NEU-TRAL.
 The towing distance must not ex- ceed 24 km.
 The towing speed must not exceed 40 km/h. If the transmission is not operable,
or the vehicle must be towed faster
than 40 km/h or farther than
24 km, it must be towed with the
front wheels OFF the ground (us-
ing a flatbed truck, towing dolly, or
wheel lift equipment with the front
wheels raised).
CAUTION!
Towing faster than 40 km/h or far-
ther than 24 km with front wheels
on the ground can cause severe
transmission damage. Such dam-
age is not covered by the New Ve-
hicle Limited Warranty.
WITHOUT THE IGNITION
KEYSpecial care must be taken when the
vehicle is towed with the ignition in the
LOCK/OFF position. Flatbed towing is the preferred towing method. How-
ever, if a flatbed towing vehicle is not
available, wheel lift towing equipment
may be used. Rear towing (with the
front wheels on the ground) is not
allowed, as transmission damage will
occur. If rear towing is the only alter-
native, the front wheels must be placed
on a towing dolly. Proper towing
equipment is necessary to prevent
damage to the vehicle.
CAUTION!
Failure to follow these towing
methods can cause severe transmis-
sion damage. Such damage is not
covered by the New Vehicle Lim-
ited Warranty.
185

3. Disconnect the glove box door
dampener from the slot on the side of
the box. This is done by grasping the
dampener connector (on the outside
of the box) and the end of the connec-
tor pin (on the inside of the box) with
your thumb and forefinger and pull-
ing outward while lightly lifting up-
ward on the door with your other
hand. Once disconnected, the damp-
ener will retract underneath the in-
strument panel if you release it.
4. Pivot the glove box downward.
5. Disengage the two retaining tabs
that secure the filter cover to the
HVAC housing and remove the cover.6. Remove the A/C Air Filter by pull-
ing it straight out of the housing.
7. Install the A/C Air Filter with the
arrow on the filter pointing toward
the floor. When installing the filter
cover, make sure the retaining tabs
fully engage the cover.
CAUTION!
The A/C air filter is identified with
an arrow to indicate airflow direc-
tion through the filter. Failure to
install the filter properly will result
in the need to replace it more often.
8. Reinstall the glove box door
dampener and glove box.
BODY LUBRICATION
Locks and all body pivot points, in-
cluding such items as seat tracks, door
hinge pivot points and rollers, and
hood hinges, should be lubricated pe-
riodically with a lithium based grease
to assure quiet, easy operation and to
protect against rust and wear. Prior to
the application of any lubricant, the parts concerned should be wiped
clean to remove dust and grit; after
lubricating excess oil and grease
should be removed. Particular atten-
tion should also be given to hood
latching components to ensure proper
function. When performing other un-
derhood services, the hood latch, re-
lease mechanism and safety catch
should be cleaned and lubricated.
The external lock cylinders should be
lubricated twice a year, preferably in
the Fall and Spring. Apply a small
amount of a high quality lubricant
directly into the lock cylinder.
CAUTION!
Car maintenance should be done at
a LANCIA Dealership. For routine
and minor maintenance operations
you wish to carry out yourself, we
do recommend you have the proper
equipment, genuine LANCIA spare
parts and the necessary fluids; do
not however carry out these opera-
tions if you have no experience.
A/C Air Filter Replacement
195

COOLING SYSTEMWARNING!
 When working near the radiatorcooling fan, disconnect the fan
motor lead or turn the ignition
switch to the LOCK position. The
fan is temperature controlled and
can start at anytime the ignition
switch is in the ON position.
 You or others can be badly
burned by hot engine coolant
(antifreeze) or steam from your
radiator. If you see or hear steam
coming from under the hood, do
not open the hood until the radia-
tor has had time to cool. Never try
to open a cooling system pressure
cap when the radiator is hot.CAUTION!
Car maintenance should be done at
a LANCIA Dealership. For routine
and minor maintenance operations
you wish to carry out yourself, we
do recommend you have the proper
equipment, genuine LANCIA spare
(Continued)
CAUTION!(Continued)
parts and the necessary fluids; do
not however carry out these opera-
tions if you have no experience.
Coolant Checks
Check engine coolant (antifreeze)
protection every 12 months (before
the onset of freezing weather, where
applicable). If the engine coolant (an-
tifreeze) is dirty or rusty in appear-
ance, the system should be drained,
flushed, and refilled with fresh engine
coolant (antifreeze). Check the front
of the A/C condenser for any accumu-
lation of bugs, leaves, etc. If dirty,
clean by gently spraying water from a
garden hose vertically down the face
of the condenser.
Check the coolant recovery bottle
tubing for brittle rubber, cracking,
tears, cuts, and tightness of the con-
nection at the bottle and radiator. In-
spect the entire system for leaks. Cooling System – Drain, Flush,
And Refill
If the engine coolant (antifreeze) is
dirty or contains a considerable
amount of sediment, clean and flush
with a reliable cooling system cleaner.
Follow with a thorough rinsing to re-
move all deposits and chemicals.
Properly dispose of old engine coolant
(antifreeze).
Refer to the “Maintenance Schedule”
for the proper maintenance intervals.
Selection Of Coolant
Use the manufacturer’s recommended
coolant or a quality-equivalent prod-
uct. Refer to “Fluids, Lubricants, and
Genuine Parts” in “Maintaining Your
Vehicle” for further information.
198

CavityCartridge Fuse Mini Fuse Description
10 — 20 Amp YellowInstrument Panel/Power Locks/
Interior Lights
11 — 15 Amp Lt Blue Selectable Power Outlet (Inside Center
Arm Rest)
12 — 20 Amp Yellow—
13 — 20 Amp YellowIgnition/Cigar Lighter
14 — 10 Amp RedInstrument Panel
15 40 Amp Green —Radiator Fan Relay
16 — 15 Amp Lt. Blue Sunroof (for versions/markets, where
provided)
17 — 10 Amp RedWireless Control Module (WCM)/
Clock/Steering Control Module (SCM)
18 40 Amp Green —Auto Shutdown (ASD) Relay
19 — 20 Amp YellowAudio Amplifier (for versions/markets,
where provided)
20 — 15 Amp Lt. Blue Radio
21 — 10 Amp RedSiren (for versions/markets, where
provided)
209

CavityCartridge Fuse Mini Fuse Description
31 — 10 Amp RedHeadlamp Washer (for versions/
markets, where provided)
32 30 Amp Pink —Auto Shutdown (ASD) Relay 1
33 — 10 Amp RedSwitch Bank/Diagnostic Link
Connector/
Powertrain Control Module (PCM)
34 30 Amp Pink —Anti-Lock Brakes (ABS) Module (for
versions/markets, where provided)/
Electronic Stability Control (ESC)
Module (for versions/markets, where
provided)
35 40 Amp Green —Anti-Lock Brakes (ABS) Module (for
versions/markets, where provided)/
Electronic Stability Control (ESC)
Module (for versions/markets, where
provided)
36 30 Amp Pink —Passenger Door Module (PDM)/Driver
Door Module (DDM)
37 —
25 Amp Natural
Power Top Module (for versions/
markets, where provided)
211