2013 Lancia Flavia wheel

Using The Power Button
Push and release the Power
Button (4) once to turn On
the TIREFIT kit. Push and
release the Power Button (4)
again to turn Off the TIREFIT kit.
Using The Deflation Button
Press the Deflation But-
ton (2) to reduce the air pres-
sure in the tire if it becomes
over-inflated.
TIREFIT USAGE
PRECAUTIONS
Replace the TIREFIT Sealant Bottle
(1) and Sealant Hose (6) prior to the
expiration date (printed on the
bottle label) to assure optimum op-
eration of the system. Refer to
“Sealing a Tire with TIREFIT” sec-
tion (F) “Sealant Bottle and Hose
Replacement”. The Sealant Bottle (1) and Sealant Hose (6) are a one tire application
use. After each use, always replace
these components immediately at
an authorized dealer.  When the TIREFIT sealant is in a
liquid form, clean water, and a
damp cloth will remove the mate-
rial from the vehicle or tire and
wheel components. Once the seal-
ant dries, it can easily be peeled off
and properly discarded.
 For optimum performance, make sure the valve stem on the wheel is
free of debris before connecting the
TIREFIT kit.

You can use the TIREFIT air pump to
inflate bicycle tires. The kit also
comes with two needles, located in
the Accessory Storage Compartment
(on the bottom of the air pump) for
inflating sport balls, rafts, or similar
inflatable items. However, use only
the Air Pump Hose (7) and make sure
the Mode Select Knob (5) is in the Air
Mode when inflating such items to
avoid injecting sealant into them.
The TIREFIT Sealant is only in-
tended to seal punctures less than 6
mm diameter in the tread of your
vehicle. Do not lift or carry the TIREFIT kit by the hoses.
WARNING!
 Do not attempt to seal a tire onthe side of the vehicle close to
traffic. Pull far enough off the
road to avoid the danger of being
hit when using the TIREFIT kit.
 Do not use TIREFIT or drive the
vehicle under the following cir-
cumstances:–
If the puncture in the tire tread
is approximately 6 mm or
larger.– If the tire has any sidewall damage.
– If the tire has any damage from
driving with extremely low tire
pressure.
– If the tire has any damage from
driving on a flat tire.
– If the wheel has any damage.
– If you are unsure of the condi- tion of the tire or the wheel.
 Keep TIREFIT away from open flame or heat source.
 A loose TIREFIT kit thrown for- ward in a collision or hard stop
could endanger the occupants of
(Continued)
174

2.
Remove the Speed Limit sticker
from the top of the Sealant Bottle (1)
and place the sticker on the instrument
panel.
3. Immediately disconnect the Seal-
ant Hose (6) from the valve stem,
reinstall the cap on the fitting at the
end of the hose, and place the TIRE-
FIT kit in the vehicle storage location.
Quickly proceed to (D) “Drive Ve-
hicle”.CAUTION!
 The metal end fitting from Power Plug (8) may get hot after use, so
it should be handled carefully.
 Failure to reinstall the cap on the
fitting at the end of the Sealant
Hose (6) can result in sealant
contacting your skin, clothing,
and the vehicle’s interior. It can
also result in sealant contacting
internal TIREFIT kit components
which may cause permanent
damage to the kit. (A) Whenever You Stop To Use
TIREFIT:
1.
Pull over to a safe location and turn
on the vehicle’s Hazard Warning flash-
ers.
2.
Verify that the valve stem (on the
wheel with the deflated tire) is in a
position that is near to the ground. This
will allow the TIREFIT Hoses (6) and
(7) to reach the valve stem and keep the
TIREFIT kit flat on the ground. This
will provide the best positioning of the
kit when injecting the sealant into the
deflated tire and running the air pump.
Move the vehicle as necessary to place
the valve stem in this position before
proceeding.
3. Place the transmission in PARK
(auto transmission) or in Gear
(manual transmission) and turn Off
the ignition.
4. Set the parking brake. (B) Setting Up To Use TIREFIT:
1. Turn the Mode Select Knob (5) to
the Sealant Mode position.
2. Uncoil the Sealant Hose (6) and
then remove the cap from the fitting
at the end of the hose.
3. Place the TIREFIT kit flat on the
ground next to the deflated tire.
4. Remove the cap from the valve
stem and then screw the fitting at the
end of the Sealant Hose (6) onto the
valve stem.
5. Uncoil the Power Plug (8) and in-
sert the plug into the vehicle’s 12 Volt
power outlet.
NOTE: Do not remove foreign ob-
jects (e.g., screws or nails) from the
tire.
(C) Injecting TIREFIT Sealant
Into The Deflated Tire:
 Always start the engine before
turning ON the TIREFIT kit.
176

PREPARATIONS FOR
JUMP-START
The battery in your vehicle is located
between the left front headlight as-
sembly and the left front wheel splash
shield. To allow jump-starting there
are remote battery posts located on
the left side of the engine compart-
ment.
WARNING!
 Take care to avoid the radiatorcooling fan whenever the hood is
raised. It can start anytime the
ignition switch is ON. You can be
injured by moving fan blades.
 Remove any metal jewelry such
as watch bands or bracelets that
might make an inadvertent elec-
trical contact. You could be seri-
ously injured.
 Batteries contain sulfuric acid that can burn your skin or eyes
and generate hydrogen gas which
is flammable and explosive. Keep
open flames or sparks away from
the battery.
1. Set the parking brake, shift the
automatic transmission into PARK
and turn the ignition to LOCK.
2. Turn off the heater, radio, and all
unnecessary electrical accessories. 3. Remove the protective cover over
the remote positive
(+)battery post.
To remove the cover, press the locking
tab and pull upward on the cover.
4. If using another vehicle to jump-
start the battery, park the vehicle
within the jumper cables reach, set
the parking brake and make sure the
ignition is OFF.
WARNING!
Do not allow vehicles to touch each
other as this could establish a
ground connection and personal in-
jury could result.
Remote Battery Posts
1 — Remote Positive (+)Post
(covered with protective cap)
2 — Remote Negative (-)Post
Locking Tab
180

CAUTION!Accessories that can be plugged into
the vehicle power outlets draw power
from the vehicle’s battery, even when
not in use (i.e., cellular phones, etc.).
Eventually, if plugged in long
enough, the vehicle’s battery will dis-
charge sufficiently to degrade battery
life and/or prevent the engine from
starting.FREEING A STUCK
VEHICLE
If your vehicle becomes stuck in mud,
sand, or snow, it can often be moved
using a rocking motion. Turn the
steering wheel right and left to clear
the area around the front wheels.Then shift back and forth between
DRIVE and REVERSE, while gently
pressing the accelerator. Use the least
amount of accelerator pedal pressure
that will maintain the rocking motion,
without spinning the wheels, or racing
the engine.
CAUTION!
Racing the engine or spinning the
wheels may lead to transmission
overheating and failure. Allow the
engine to idle with the transmission
in NEUTRAL for at least one min-
ute after every five rocking-motion
cycles. This will minimize over-
heating and reduce the risk of
transmission failure during pro-
longed efforts to free a stuck ve-
hicle.NOTE:
Press the "ESC Off" switch,
to place the Electronic Stability
Control (ESC) system in "Partial Off"
mode, before rocking the vehicle.
Refer to “Electronic Brake Control”
in “Starting And Operating” for fur-
ther information. Once the vehicle
has been freed, press the "ESC Off"
switch again to restore "ESC On"
mode.
CAUTION!
 When “rocking” a stuck vehicle by shifting between DRIVE and
REVERSE, do not spin the
wheels faster than 24 km/h, or
drivetrain damage may result.
 Revving the engine or spinning
the wheels too fast may lead to
transmission overheating and
failure. It can also damage the
tires. Do not spin the wheels
above 48 km/h while in gear (no
transmission shifting occurring).
182

WARNING!
Fast spinning tires can be danger-
ous. Forces generated by excessive
wheel speeds may cause damage, or
even failure, of the axle and tires. A
tire could explode and injure some-
one. Do not spin your vehicle's
wheels faster than 48 km/h or for
longer than 30 seconds continu-
ously without stopping when you
are stuck and do not let anyone
near a spinning wheel, no matter
what the speed.SHIFT LEVER
OVERRIDE
If a malfunction occurs and the shift
lever cannot be moved out of the
PARK position, you can use the fol-
lowing procedure to temporarily
move the shift lever:
1. Turn the engine OFF.
2. Firmly apply the parking brake.
3. Remove the rubber cupholder
liner. Squeeze one side of the liner's
center to expose its edge and facilitate
removal.
4. Turn the ignition to the ACC or
ON/RUN position, but do not start the
engine.
5. Press and maintain firm pressure
on the brake pedal. 6. Insert a screwdriver or similar tool
into the access hole (at the front of the
cupholder) and push and hold the
override release lever forward.
7. Move the shift lever into the NEU-
TRAL position.
8. The vehicle may then be started in
NEUTRAL.
9. Reinstall the cupholder liner.
Shift Lever Override
183

TOWING A DISABLED VEHICLE
This section describes the procedures for towing a disabled vehicle using a commercial wrecker service.Towing ConditionWheels OFF the GroundAutomatic Transmissions
Flat Tow NONEIf transmission is operable:
 Transmission inNEUTRAL
 40 km/h maxspeed
 24 km maxdistance
Wheel Lift Or Dolly Tow
Rear
Front OK
Flatbed ALLBEST METHOD
Proper towing or lifting equipment is
required to prevent damage to your
vehicle. Use only tow bars and other
equipment designed for this purpose,
following equipment manufacturer’s
instructions. Use of safety chains is
mandatory. Attach a tow bar or other
towing device to main structural
members of the vehicle, not to bum-
pers or associated brackets. State and
local laws regarding vehicles under
tow must be observed.
If you must use the accessories (wipers,
defrosters, etc.) while being towed, the
ignition must be in the ON/RUN posi-
tion, not the ACC position.If the vehicle's battery is discharged,
see "Shift Lever Override" in "What
To Do In Emergencies" for instruc-
tions on shifting the automatic trans-
mission out of PARK for towing.
CAUTION!
 Do not use sling type equipment when towing. Damage to the fas-
cia will occur.
 When securing the vehicle to a
flatbed truck, do not attach to
front or rear suspension compo-
nents. Damage to your vehicle
may result from improper towing.
 Do not push or tow this vehicle with another vehicle as damage to
the bumper fascia and transmis-
sion may result.
184

AUTOMATIC
TRANSMISSION
The manufacturer recommends tow-
ing your vehicle with all four wheels
OFF the ground using a flatbed.
If flatbed equipment is not available,
and the transmission is operable, the
vehicle may be flat towed (with all
four wheels on the ground) under the
following conditions:
 The transmission must be in NEU-TRAL.
 The towing distance must not ex- ceed 24 km.
 The towing speed must not exceed 40 km/h. If the transmission is not operable,
or the vehicle must be towed faster
than 40 km/h or farther than
24 km, it must be towed with the
front wheels OFF the ground (us-
ing a flatbed truck, towing dolly, or
wheel lift equipment with the front
wheels raised).
CAUTION!
Towing faster than 40 km/h or far-
ther than 24 km with front wheels
on the ground can cause severe
transmission damage. Such dam-
age is not covered by the New Ve-
hicle Limited Warranty.
WITHOUT THE IGNITION
KEYSpecial care must be taken when the
vehicle is towed with the ignition in the
LOCK/OFF position. Flatbed towing is the preferred towing method. How-
ever, if a flatbed towing vehicle is not
available, wheel lift towing equipment
may be used. Rear towing (with the
front wheels on the ground) is not
allowed, as transmission damage will
occur. If rear towing is the only alter-
native, the front wheels must be placed
on a towing dolly. Proper towing
equipment is necessary to prevent
damage to the vehicle.
CAUTION!
Failure to follow these towing
methods can cause severe transmis-
sion damage. Such damage is not
covered by the New Vehicle Lim-
ited Warranty.
185

LANCIA engine air cleaner filters are
a high quality filter and are recom-
mended.
MAINTENANCE-FREE
BATTERY
The top of the maintenance-free bat-
tery is permanently sealed. You will
never have to add water, nor is peri-
odic maintenance required.
NOTE: The battery is stored in a
compartment behind the left front
fender and is accessible without
removing the tire and wheel. Re-
mote battery terminals are located
in the engine compartment for
jump-starting. Refer to “Jump-
Starting Procedures” in “What To
Do In Emergencies” for further
information.
To access the battery, turn the steering
wheel fully to the right and remove
the inner fender shield.
WARNING!
 Battery fluid is a corrosive acidsolution and can burn or even
blind you. Do not allow battery
fluid to contact your eyes, skin, or
clothing. Do not lean over a bat-
tery when attaching clamps. If
acid splashes in eyes or on skin,
flush the area immediately with
large amounts of water.
 Battery gas is flammable and ex-
plosive. Keep flame or sparks
away from the battery. Do not use
a booster battery or any other
booster source with an output
greater than 12 Volts. Do not al-
low cable clamps to touch each
other.
 Battery posts, terminals, and re- lated accessories contain lead and
lead compounds. Wash hands af-
ter handling.
CAUTION!
 It is essential when replacing thecables on the battery that the
positive cable is attached to the
positive post and the negative
cable is attached to the negative
post. Battery posts are marked
positive (+) and negative (-) and
are identified on the battery case.
Cable clamps should be tight on
the terminal posts and free of cor-
rosion.
 If a “fast charger” is used while the battery is in the vehicle, dis-
connect both vehicle battery
cables before connecting the
charger to the battery. Do not use
a “fast charger” to provide start-
ing voltage.
193