2013 Lancia Flavia steering

ANTI-LOCK BRAKE
SYSTEM (ABS)
This system aids the driver in main-
taining vehicle control under adverse
braking conditions. The system con-
trols hydraulic brake pressure to pre-
vent wheel lock-up and help avoid
skidding on slippery surfaces during
braking. Refer to “Anti-Lock Brake
System” in “Starting and Operating”
for further information.
TRACTION CONTROL
SYSTEM (TCS)
This system monitors the amount of
wheel spin of each of the driven
wheels. If wheel spin is detected,
brake pressure is applied to the slip-
ping wheel(s) and engine power is
reduced to provide enhanced accel-
eration and stability. A feature of the
TCS system functions similar to a lim-
ited slip differential and controls the
wheel spin across a driven axle. If one
wheel on a driven axle is spinning
faster than the other, the system will
apply the brake of the spinning wheel.
This will allow more engine torque tobe applied to the wheel that is not
spinning. This feature remains active
even if TCS and ESC are in the “Par-
tial Off” mode. Refer to “Electronic
Stability Control (ESC)” in this sec-
tion of this manual.
BRAKE ASSIST SYSTEM
(BAS)The BAS is designed to optimize the
vehicle’s braking capability during
emergency braking maneuvers. The
system detects an emergency braking
situation by sensing the rate and
amount of brake application and then
applies optimum pressure to the
brakes. This can help reduce braking
distances. The BAS complements the
Anti-Lock Brake System (ABS). Ap-
plying the brakes very quickly results
in the best BAS assistance. To receive
the benefit of the system, you must
apply continuous braking pressure
during the stopping sequence. Do not
reduce brake pedal pressure unless
braking is no longer desired. Once the
brake pedal is released, the BAS is
deactivated.
WARNING!
 The BAS cannot prevent the
natural laws of physics from act-
ing on the vehicle, nor can it in-
crease braking efficiency beyond
that afforded by the condition of
the vehicle brakes and tires or the
traction afforded.
The BAS cannot prevent collisions,
including those resulting from ex-
cessive speed in turns, following
another vehicle too closely, or hy-
droplaning.The capabilities of a BAS-equipped
vehicle must never be exploited in a
reckless or dangerous manner,
which could jeopardize the user’s
safety or the safety of others.
ELECTRONIC STABILITY
CONTROL (ESC)
This system enhances directional con-
trol and stability of the vehicle under
various driving conditions. ESC cor-
rects for over/under steering of the
vehicle by applying the brake of the
appropriate wheel to assist in counter-
acting the over/under steer condition.
154

Engine power may also be reduced to
help the vehicle maintain the desired
path. ESC uses sensors in the vehicle
to determine the vehicle path in-
tended by the driver and compares it
to the actual path of the vehicle. When
the actual path does not match the
intended path, ESC applies the brake
of the appropriate wheel to assist in
counteracting the oversteer or under-
steer condition.
 Over-steer - when the vehicle isturning more than appropriate for
the steering wheel position.
 Under-steer - when the vehicle is turning less than appropriate for
the steering wheel position.WARNING!
The Electronic Stability Control
(ESC) cannot prevent the natural
laws of physics from acting on the
vehicle, nor can it increase the trac-
tion afforded by prevailing road
conditions. ESC cannot prevent ac-
cidents, including those resulting
(Continued)
WARNING!(Continued)
from excessive speed in turns, driv-
ing on very slippery surfaces, or
hydroplaning. ESC also cannot
prevent accidents resulting from
loss of vehicle control due to inap-
propriate driver input for the con-
ditions. Only a safe, attentive, and
skillful driver can prevent acci-
dents. The capabilities of an ESC
equipped vehicle must never be ex-
ploited in a reckless or dangerous
manner which could jeopardize the
user’s safety or the safety of others.
ESC Operating Modes
All ESC equipped vehicles can choose
the following ESC operating modes:
ESC On
This is the normal operating mode for
ESC. Whenever the vehicle is started
the ESC system will be in this mode.
This mode should be used for almost
all driving situations. ESC should
only be turned to “Partial Off” for
specific reasons as noted below. Partial ESC Mode
This mode is entered by momentarily
pressing the “ESC Off” switch (located
in the lower switch bank below the
heater/air conditioning controls). When
in “Partial Off” mode, the TCS portion
of ESC, except for the limited slip fea-
ture described in the TCS section, has
been disabled and the “ESC Activation/
Malfunction Indicator Light” will be il-
luminated. All other stability features of
ESC function normally, with the excep-
tion of engine power reduction. This
mode is intended to be used if the ve-
hicle is in deep snow, sand, or gravel
conditions and more wheel spin than
ESC would normally allow is required
to gain traction.
ESC Off Switch
155

TIRES — GENERAL
INFORMATION
TIRE PRESSURE
Proper tire inflation pressure is essen-
tial to the safe and satisfactory opera-
tion of your vehicle. Three primary
areas are affected by improper tire
pressure:
SafetyWARNING!
 Improperly inflated tires are dan-gerous and can cause collisions.
 Under-inflation increases tire
flexing and can result in over-
heating and tire failure.
 Over-inflation reduces a tire's ability to cushion shock. Objects
on the road and chuckholes can
cause damage that result in tire
failure.
 Over-inflated or under-inflated
tires can affect vehicle handling
and can fail suddenly, resulting in
loss of vehicle control.
(Continued)
WARNING!(Continued)
 Unequal tire pressures can cause steering problems. You could lose
control of your vehicle.
 Unequal tire pressures from one side of the vehicle to the other can
cause the vehicle to drift to the
right or left.
 Always drive with each tire in- flated to the recommended cold
tire inflation pressure.
Economy
Improper inflation pressures can
cause uneven wear patterns to de-
velop across the tire tread. These ab-
normal wear patterns will reduce
tread life resulting in a need for earlier
tire replacement. Under-inflation also
increases tire rolling resistance result-
ing in higher fuel consumption.
Ride Comfort And Vehicle
Stability
Proper tire inflation contributes to a
comfortable ride. Over-inflation pro-
duces a jarring and uncomfortable
ride. TIRE INFLATION
PRESSURES
The proper cold tire inflation pressure
is listed on the driver's side B-Pillar or
rear edge of the driver's side door.
Some vehicles may have Supplemen-
tal Tire Pressure Information for ve-
hicle loads that are less than the maxi-
mum loaded vehicle condition. These
pressure conditions will be found in
the “Supplemental Tire Pressure In-
formation” section of this manual.
The pressure should be checked and
adjusted as well as inspecting for signs
of tire wear or visible damage at least
once a month. Use a good quality
pocket-type gauge to check tire pres-
sure. Do not make a visual judgement
when determining proper inflation.
Radial tires may look properly in-
flated even when they are under-
inflated.
157

REPLACEMENT TIRES
The tires on your new vehicle provide
a balance of many characteristics.
They should be inspected regularly
for wear and correct cold tire inflation
pressure. The manufacturer strongly
recommends that you use tires
equivalent to the originals in size,
quality and performance when re-
placement is needed (refer to the
paragraph on “Tread Wear Indica-
tors”). Refer to the “Tire and Loading
Information” placard for the size des-
ignation of your tire. The Load Index
and Speed Symbol for your tire will be
found on registration Document/log
book.
It is recommended to replace the two
front tires or two rear tires as a pair.
Replacing just one tire can seriously
affect your vehicle’s handling. If you
ever replace a wheel, make sure that
the wheel’s specifications match those
of the original wheels.It is recommended you contact your
original equipment or an authorized
tire dealer with any questions you
may have on tire specifications or ca-
pability. Failure to use equivalent re-
placement tires may adversely affect
the safety, handling, and ride of your
vehicle.
WARNING!
Do not use a tire, wheel size or
rating other than that specified for
your vehicle. Some combinations
of unapproved tires and wheels
may change suspension dimen-
sions and performance character-
istics, resulting in changes to
steering, handling, and braking of
your vehicle. This can cause un-
predictable handling and stress to
steering and suspension compo-
nents. You could lose control and
have a collision resulting in serious
injury or death. Use only the tire
and wheel sizes with load ratings
approved for your vehicle.
(Continued)
WARNING!
(Continued)
Never use a tire with a smaller load
index or capacity, other than what
was originally equipped on your ve-
hicle. Using a tire with a smaller
load index could result in tire over-
loading and failure. You could lose
control and have a collision.Failure to equip your vehicle with
tires having adequate speed capa-
bility can result in sudden tire fail-
ure and loss of vehicle control.CAUTION!Replacing original tires with tires of a
different size may result in false
speedometer and odometer readings.TIRE CHAINSUse of Security Chain Company (SCC)
Super Z6 low profile (P/N SZ-139) or
equivalent are recommended on 215/55
R18 95H tires with 18 x 7.0 wheels,
40 mm offset.
160

CAUTION!
To avoid damage to your vehicle or
tires, observe the following precau-
tions:
Because of restricted chain clear-
ance between tires and other sus-
pension components, it is impor-
tant that only chains in good
condition are used. Broken chains
can cause serious damage. Stop
the vehicle immediately if noise
occurs that could indicate chain
breakage. Remove the damaged
parts of the chain before further
use. Do not exceed 70 km/h.
 Drive cautiously and avoid severeturns and large bumps, especially
with a loaded vehicle.
 Install chains on the front wheels as tightly as possible and then
retighten after driving about
0.8 km.
 Do not drive for prolonged peri- ods of time on dry pavement.
(Continued)
CAUTION!(Continued)
Observe the tire chain manufactur-
er's instructions on the method of
installation, operating speed, and
conditions for use. Always use the
lower suggested operating speed of
the chain manufacturer, if different
from the speed recommended by
the vehicle manufacturer.
This notice applies to all chain trac-
tion devices, including link and cable
(radial) chains.
TIRE ROTATION
RECOMMENDATIONS
Tires on the front and rear axles of
vehicles operate at different loads and
perform different steering, driving,
and braking functions. For these rea-
sons, they wear at unequal rates.These effects can be reduced by timely
rotation of tires. The benefits of rota-
tion are especially worthwhile with ag-
gressive tread designs such as those on
all season type tires. Rotation will in-
crease tread life, help to maintain mud,
snow, and wet traction levels, and con-
tribute to a smooth, quiet ride.
Refer to the “Maintenance Schedule”
for the proper maintenance intervals.
The reasons for any rapid or unusual
wear should be corrected prior to ro-
tation being performed.
TIRE PRESSURE
MONITOR SYSTEM
(TPMS)
The Tire Pressure Monitor System
(TPMS) will warn the driver of a low
tire pressure based on the vehicle rec-
ommended cold placard pressure.
The tire pressure will vary with tem-
perature by about 7 kPa for every
7°C. This means that when the out-
side temperature decreases, the tire
pressure will decrease. Tire pressure
should always be set based on cold
inflation tire pressure. This is defined
as the tire pressure after the vehicle
has not been driven for at least three
hours, or driven less than 1.6 km after
a three hour period. The cold tire in-
flation pressure must not exceed the
maximum inflation pressure molded
into the tire sidewall. Refer to “Tires –
General Information” in “Starting
161

CAUTION!Accessories that can be plugged into
the vehicle power outlets draw power
from the vehicle’s battery, even when
not in use (i.e., cellular phones, etc.).
Eventually, if plugged in long
enough, the vehicle’s battery will dis-
charge sufficiently to degrade battery
life and/or prevent the engine from
starting.FREEING A STUCK
VEHICLE
If your vehicle becomes stuck in mud,
sand, or snow, it can often be moved
using a rocking motion. Turn the
steering wheel right and left to clear
the area around the front wheels.Then shift back and forth between
DRIVE and REVERSE, while gently
pressing the accelerator. Use the least
amount of accelerator pedal pressure
that will maintain the rocking motion,
without spinning the wheels, or racing
the engine.
CAUTION!
Racing the engine or spinning the
wheels may lead to transmission
overheating and failure. Allow the
engine to idle with the transmission
in NEUTRAL for at least one min-
ute after every five rocking-motion
cycles. This will minimize over-
heating and reduce the risk of
transmission failure during pro-
longed efforts to free a stuck ve-
hicle.NOTE:
Press the "ESC Off" switch,
to place the Electronic Stability
Control (ESC) system in "Partial Off"
mode, before rocking the vehicle.
Refer to “Electronic Brake Control”
in “Starting And Operating” for fur-
ther information. Once the vehicle
has been freed, press the "ESC Off"
switch again to restore "ESC On"
mode.
CAUTION!
 When “rocking” a stuck vehicle by shifting between DRIVE and
REVERSE, do not spin the
wheels faster than 24 km/h, or
drivetrain damage may result.
 Revving the engine or spinning
the wheels too fast may lead to
transmission overheating and
failure. It can also damage the
tires. Do not spin the wheels
above 48 km/h while in gear (no
transmission shifting occurring).
182

ENGINE COMPARTMENT — 2.4L1 — Engine Coolant Reservoir6 — Air Cleaner Filter
2 — Power Steering Fluid Reservoir 7 — Engine Oil Fill
3 — Brake Fluid Reservoir 8 — Coolant Pressure Cap
4 — Power Distribution Center (Fuses) 9 — Engine Oil Dipstick
5 — Integrated Power Module (Fuses) 10 — Washer Fluid Reservoir
189

CAUTION!(Continued)
Car maintenance should be done
at a LANCIA Dealership. For rou-
tine and minor maintenance op-
erations you wish to carry out
yourself, we do recommend you
have the proper equipment, genu-
ine LANCIA spare parts and the
necessary fluids; do not however
carry out these operations if you
have no experience. Your vehicle has been built with improved fluids that protect the
performance and durability of
your vehicle and also allow ex-
tended maintenance intervals. Do
not use chemical flushes in these
components as the chemicals can
damage your engine, transmis-
sion, power steering or air condi-
tioning. Such damage is not cov-
ered by the New Vehicle Limited
Warranty. If a flush is needed be-
cause of component malfunction,
use only the specified fluid for the
flushing procedure. ENGINE OIL
Checking Oil Level
To assure proper engine lubrication of
your vehicle's engine, the engine oil
must be maintained at the correct
level. The best time to check the en-
gine oil level is about five minutes
after a fully warmed engine is shut off.
Do not check oil level before starting
the engine after it has sat overnight.
Checking engine oil level when the
engine is cold will give you an incor-
rect reading.
Checking the oil while the vehicle is
on level ground and only when the
engine is hot, will improve the accu-
racy of the oil level readings. Maintain
the oil level between the range mark-
ings on the dipstick. Either the range
markings consist of a crosshatch zone
marked SAFE or a crosshatch zone
marked with MIN at the low end of
the range and MAX at the high end of
the range. Adding 1.0 Liter of oil
when the reading is at the low end of
the range marking will raise the oil
level to the high end of the range
marking.
CAUTION!
 Do not overfill the engine. Over-
filling the engine will cause oil
aeration, which can lead to loss of
oil pressure and an increase in oil
temperature. This could damage
your engine. Also, be sure the oil
fill cap is replaced and tightened
after adding oil.
Car maintenance should be done
at a LANCIA Dealership. For rou-
tine and minor maintenance op-
erations you wish to carry out
yourself, we do recommend you
have the proper equipment, genu-
ine LANCIA spare parts and the
necessary fluids; do not however
carry out these operations if you
have no experience.
Change Engine Oil
Refer to the “Maintenance Schedule”
for the proper maintenance intervals.
191