2013 Lancia Flavia transmission

AUTOSTICK®AutoStick® is a driver-interactive
transmission feature providing manual
shift control, giving you more control of
the vehicle. AutoStick® allows you to
maximize engine braking, eliminate un-
desirable upshifts and downshifts, and
improve overall vehicle performance.
This system can also provide you with
more control during passing, city driv-
ing, cold slippery conditions, mountain
driving, and many other situations.OPERATIONWhen the shift lever is in the
AutoStick® position (below the DRIVE
position), it can be moved from side to
side. This allows the driver to manually
select the transmission gear being used.
Moving the shift lever to the left (-)
triggers a downshift and to the right (+)
an upshift. The current gear will be
displayed in the instrument cluster.
NOTE:
In AutoStick® mode, the
transmission will only shift up or
down when the driver moves the
shift lever to the right (+) or left (-),
unless an engine lugging or over-
speed condition would result. It will
remain in the selected gear until an-
other upshift or downshift is chosen,
except as described below.
 The transmission will automati- cally downshift to first gear when
coming to a stop. After a stop, the
driver should manually upshift (+)
the transmission as the vehicle is
accelerated.
You can start out, from a stop, in any
gear except top gear. Tapping (+) (at
a stop) will allow starting in second
gear. Starting out in second gear is
helpful in snowy or icy conditions. The transmission will automati- cally upshift when necessary to pre-
vent engine over-speed.
 If a downshift would cause the en- gine to overspeed, that shift will not
occur until it is safe for the engine.  Avoid using speed control when
AutoStick® is engaged.

Transmission shifting will be more
noticeable when AutoStick® is
engaged. If the system detects powertrain overheating, the transmission will
revert to automatic shift mode and
remain in that mode until the pow-
ertrain cools off.
 If the system detects a problem, it will disable AutoStick® mode and
the transmission will return to au-
tomatic mode until the problem is
corrected.
To disengage AutoStick® mode, re-
turn the shift lever to the DRIVE po-
sition. You can shift in or out of the
AutoStick® position at any time with-
out taking your foot off the accelera-
tor pedal.
147

SHALLOW STANDING
WATER
Although your vehicle is capable of
driving through shallow standing
water, consider the following Caution
and Warning before doing so.CAUTION!
 Always check the depth of thestanding water before driving
through it. Never drive through
standing water that is deeper
than the bottom of the tire rims
mounted on the vehicle.
 Determine the condition of the road or the path that is under
water and if there are any ob-
stacles in the way before driving
through the standing water.
 Do not exceed 8 km/h when driv- ing through standing water. This
will minimize wave effects.
(Continued)
CAUTION!(Continued)
 Driving through standing water may cause damage to your vehi-
cle’s drivetrain components. Al-
ways inspect your vehicle’s fluids
(i.e., engine oil, transmission,
axle, etc.) for signs of contamina-
tion (i.e., fluid that is milky or
foamy in appearance) after driv-
ing through standing water. Do
not continue to operate the ve-
hicle if any fluid appears con-
taminated, as this may result in
further damage. Such damage is
not covered by the New Vehicle
Limited Warranty.
Getting water inside your vehicle’s
engine can cause it to lock up and
stall out, and cause serious inter-
nal damage to the engine. Such
damage is not covered by the New
Vehicle Limited Warranty.
WARNING!
 Driving through standing water limits your vehicle’s traction ca-
pabilities. Do not exceed 8 km/h
when driving through standing
water.
 Driving through standing water
limits your vehicle’s braking ca-
pabilities, which increases stop-
ping distances. Therefore, after
driving through standing water,
drive slowly and lightly press on
the brake pedal several times to
dry the brakes.
 Getting water inside your vehi-
cle’s engine can cause it to lock up
and stall out, and leave you
stranded.
 Failure to follow these warnings may result in injuries that are se-
rious or fatal to you, your passen-
gers, and others around you.
149

PARKING BRAKE
Before leaving the vehicle, make sure
that the parking brake is fully ap-
plied. Also, be certain to leave the
transmission in PARK.
The parking brake lever is located in
the center console. To apply the park-
ing brake, pull the lever up as firmly
as possible. To release the parking
brake, pull the lever up slightly, press
the center button, then lower the lever
completely.
When the parking brake is applied
with the ignition switch ON, the
“Brake Warning Light” in the instru-
ment cluster will illuminate.NOTE:
 When the parking brake is ap-
plied and the transmission is
placed in gear, the “Brake Warn-
ing Light” will flash. If vehicle
speed is detected, a chime will
sound to alert the driver. Fully
release the parking brake before
attempting to move the vehicle.
 This light only shows that the parking brake is applied. It does
not show the degree of brake
application.
When parking on a hill, it is important
to turn the front wheels toward the
curb on a downhill grade and away
from the curb on an uphill grade.
Apply the parking brake before plac-
ing the shift lever in PARK, otherwise
the load on the transmission locking
mechanism may make it difficult to
move the shift lever out of PARK. The
parking brake should always be ap-
plied whenever the driver is not in the
vehicle.
WARNING!
 Never use the PARK position as a substitute for the parking brake.
Always apply the parking brake
fully when parked to guard
against vehicle movement and
possible injury or damage.
 When leaving the vehicle, always remove the key fob from the igni-
tion and lock your vehicle.
 Never leave children alone in a vehicle, or with access to an un-
locked vehicle. Allowing children
to be in a vehicle unattended is
dangerous for a number of rea-
sons. A child or others could be
seriously or fatally injured. Chil-
dren should be warned not to
touch the parking brake, brake
pedal or the shift lever.
 Do not leave the key fob in or near the vehicle. A child could operate
power windows, other controls, or
move the vehicle.
 Be sure the parking brake is fully disengaged before driving; failure
to do so can lead to brake failure
and a collision.
(Continued)
Parking Brake
150

WARNING!(Continued)
Always fully apply the parking
brake when leaving your vehicle
or it may roll and cause damage or
injury. Also, be certain to leave the
transmission in PARK. Failure to
do so may cause the vehicle to roll
and cause damage or injury.CAUTION!
If the “Brake Warning Light” re-
mains on with the parking brake
released, a brake system malfunc-
tion is indicated. Have the brake
system serviced by an authorized
dealer immediately.
ANTI-LOCK BRAKE
SYSTEM (ABS)
The Anti-Lock Brake System (ABS)
provides increased vehicle stability
and brake performance under most
braking conditions. The system oper-
ates with a separate computer to
modulate the hydraulic pressure to
prevent wheel lock-up and avoid
skidding on slippery surfaces.
WARNING!
 Pumping of the anti-lock brakes will diminish their effectiveness
and may lead to a collision.
Pumping makes the stopping dis-
tance longer. Just press firmly on
your brake pedal when you need
to slow down or stop.
 The ABS cannot prevent the natural laws of physics from act-
ing on the vehicle, nor can it in-
crease braking or steering effi-
ciency beyond that afforded by
the condition of the vehicle
brakes and tires or the traction
afforded.
 The ABS cannot prevent colli- sions, including those resulting
from excessive speed in turns, fol-
lowing another vehicle too
closely, or hydroplaning.
 The capabilities of an ABS-
equipped vehicle must never be
exploited in a reckless or danger-
ous manner, which could jeopar-
dize the user's safety or the safety
of others. The “Anti-Lock Brake
Warning Light” monitors
the Anti-Lock Brake Sys-
tem. The light will come on
when the ignition switch is turned to
the ON position and may stay on for
as long as four seconds.
If the “Anti-Lock Brake Warning
Light” remains on or comes on while
driving, it indicates that the anti-lock
portion of the brake system is not func-
tioning and that service is required.
However, the conventional brake sys-
tem will continue to operate normally
if the “Brake Warning Light” is not on.
If the “Anti-Lock Brake Warning
Light” is on, the brake system should
be serviced as soon as possible to re-
store the benefits of anti-lock brakes.
If the “Anti-Lock Brake Warning
Light” does not come on when the
ignition switch is turned to the ON
position, have the bulb repaired as
soon as possible.
151

RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.)
TOWING THIS VEHICLE BEHIND ANOTHER VEHICLE
Towing ConditionWheels OFF the
Ground All Models
Flat Tow NONENOT ALLOWED
Dolly Tow FrontOK
Rear NOT ALLOWED
On Trailer ALLOK
RECREATIONAL TOWING –
ALL MODELS
Recreational towing is allowed ONLY
if the front wheels are OFF the ground.
This may be accomplished using a tow
dolly or vehicle trailer. If using a tow
dolly, follow this procedure:1. Properly secure the dolly to the
tow vehicle, following the dolly
manufacturer's instructions. 2. Drive the front wheels onto the tow
dolly.
3. Firmly apply the parking brake.
Place the transmission in PARK.
4. Properly secure the front wheels to
the dolly, following the dolly manu-
facturer's instructions.
5. Release the parking brake.
CAUTION!
DO NOT flat tow this vehicle.
Damage to the drivetrain will re-
sult. Towing this vehicle in violation of
the above requirements can cause
severe transmission damage.
Damage from improper towing is
not covered under the New Ve-
hicle Limited Warranty.
169

6
WHAT TO DO IN EMERGENCIES
 HAZARD WARNING FLASHERS . . . . . . . . . . . . .172
 IF YOUR ENGINE OVERHEATS . . . . . . . . . . . . . .172  ENGINE OIL OVERHEATING . . . . . . . . . . . . . .173
 TIREFIT KIT . . . . . . . . . . . . . . . . . . . . . . . . . . . .173
 TIREFIT STORAGE . . . . . . . . . . . . . . . . . . . . .173
 TIREFIT KIT COMPONENTS ANDOPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . .173
 TIREFIT USAGE PRECAUTIONS . . . . . . . . . . .174
 SEALING A TIRE WITH TIREFIT. . . . . . . . . . .175
 JUMP-STARTING . . . . . . . . . . . . . . . . . . . . . . . . .179
 PREPARATIONS FOR JUMP-START . . . . . . . . .180
 JUMP-STARTING PROCEDURE . . . . . . . . . . . .181
 FREEING A STUCK VEHICLE . . . . . . . . . . . . . . .182
 SHIFT LEVER OVERRIDE . . . . . . . . . . . . . . . . .183
 TOWING A DISABLED VEHICLE . . . . . . . . . . . .184
 AUTOMATIC TRANSMISSION . . . . . . . . . . . . .185
 WITHOUT THE IGNITION KEY . . . . . . . . . . . .185
171

2.
Remove the Speed Limit sticker
from the top of the Sealant Bottle (1)
and place the sticker on the instrument
panel.
3. Immediately disconnect the Seal-
ant Hose (6) from the valve stem,
reinstall the cap on the fitting at the
end of the hose, and place the TIRE-
FIT kit in the vehicle storage location.
Quickly proceed to (D) “Drive Ve-
hicle”.CAUTION!
 The metal end fitting from Power Plug (8) may get hot after use, so
it should be handled carefully.
 Failure to reinstall the cap on the
fitting at the end of the Sealant
Hose (6) can result in sealant
contacting your skin, clothing,
and the vehicle’s interior. It can
also result in sealant contacting
internal TIREFIT kit components
which may cause permanent
damage to the kit. (A) Whenever You Stop To Use
TIREFIT:
1.
Pull over to a safe location and turn
on the vehicle’s Hazard Warning flash-
ers.
2.
Verify that the valve stem (on the
wheel with the deflated tire) is in a
position that is near to the ground. This
will allow the TIREFIT Hoses (6) and
(7) to reach the valve stem and keep the
TIREFIT kit flat on the ground. This
will provide the best positioning of the
kit when injecting the sealant into the
deflated tire and running the air pump.
Move the vehicle as necessary to place
the valve stem in this position before
proceeding.
3. Place the transmission in PARK
(auto transmission) or in Gear
(manual transmission) and turn Off
the ignition.
4. Set the parking brake. (B) Setting Up To Use TIREFIT:
1. Turn the Mode Select Knob (5) to
the Sealant Mode position.
2. Uncoil the Sealant Hose (6) and
then remove the cap from the fitting
at the end of the hose.
3. Place the TIREFIT kit flat on the
ground next to the deflated tire.
4. Remove the cap from the valve
stem and then screw the fitting at the
end of the Sealant Hose (6) onto the
valve stem.
5. Uncoil the Power Plug (8) and in-
sert the plug into the vehicle’s 12 Volt
power outlet.
NOTE: Do not remove foreign ob-
jects (e.g., screws or nails) from the
tire.
(C) Injecting TIREFIT Sealant
Into The Deflated Tire:
 Always start the engine before
turning ON the TIREFIT kit.
176

NOTE:
Manual transmission ve-
hicles must have the parking brake
engaged and the shift lever in NEU-
TRAL.
After pressing the Power Button (4),
the sealant (white fluid) will flow
from the Sealant Bottle (1) through
the Sealant Hose (6) and into the
tire.NOTE: Sealant may leak out
through the puncture in the tire.
If the sealant (white fluid) does not
flow within 0 – 10 seconds through
the Sealant Hose (6):
1. Press the Power Button (4) to turn
Off the TIREFIT kit. Disconnect the
Sealant Hose (6) from the valve stem.
Make sure the valve stem is free of
debris. Reconnect the Sealant
Hose (6) to the valve stem. Check that
the Mode Select Knob (5) is in the
Sealant Mode position and not Air
Mode. Press the Power Button (4) to
turn On the TIREFIT kit. 2. Connect the Power Plug (8) to a
different 12 Volt power outlet in your
vehicle or another vehicle, if avail-
able. Make sure the engine is running
before turning ON the TIREFIT kit.
3.
The Sealant Bottle (1) may be empty
due to previous use. Call for assistance.
NOTE: If the Mode Select
Knob (5) is on Air Mode and the
pump is operating, air will dis-
pense from the Air Pump Hose (7)
only, not the Sealant Hose (6).
If the sealant (white fluid) does
flow through the Sealant Hose (6):
1.
Continue to operate the pump until
sealant is no longer flowing through
hose (typically takes 30 - 70 seconds).
As the sealant flows through the Sealant
Hose (6), the Pressure Gauge (3) can
read as high as 70 psi (5 Bar). The
Pressure Gauge (3) will decrease
quickly from approximately 70 psi
(5 Bar) to the actual tire pressure when
the Sealant Bottle (1) is empty.
2. The pump will start to inject air
into the tire immediately after the
Sealant Bottle (1) is empty. Continue
to operate the pump and inflate the
tire to the pressure indicated on the
tire pressure label on the driver-side
latch pillar (recommended pressure).
Check the tire pressure by looking at
the Pressure Gauge (3).
If the tire does not inflate to at least
26 psi (1.8 Bar) pressure within
15 minutes:
 The tire is too badly damaged. Do
not attempt to drive the vehicle fur-
ther. Call for assistance.
NOTE: If the tire becomes over-
inflated, press the Deflation But-
ton to reduce the tire pressure to
the recommended inflation pres-
sure before continuing.
177