2013 JEEP GRAND CHEROKEE remote start

Vehicles Equipped With Remote Start
On models that are equipped with remote start,
the heated steering wheel can be programmed
to come on during a remote start. Refer to
“Remote Starting System — If Equipped” in
“Things to Know Before Starting Your Vehicle”
for further information.
WARNING!
•Persons who are unable to feel pain to the
skin because of advanced age, chronic
illness, diabetes, spinal cord injury, medi-
cation, alcohol use, exhaustion, or other
physical conditions must exercise care
when using the steering wheel heater. It
may cause burns even at low tempera-
tures, especially if used for long periods.
• Do not place anything on the steering
wheel that insulates against heat, such as
a blanket or steering wheel covers of any
type and material. This may cause the
steering wheel heater to overheat.
ELECTRONIC SPEED
CONTROL — IF EQUIPPED
When engaged, the Electronic Speed Control
takes over accelerator operations at speeds
greater than 20 mph (32 km/h).
The Electronic Speed Control buttons are lo-
cated on the right side of the steering wheel. NOTE:
In order to ensure proper operation, the Elec-
tronic Speed Control System has been de-
signed to shut down if multiple Speed Control
functions are operated at the same time. If this
occurs, the Electronic Speed Control System
can be reactivated by pushing the Electronic
Speed Control ON/OFF button and resetting the
desired vehicle set speed.
To ActivatePush the ON/OFF button. The Cruise Indicator
Light in the instrument cluster will illuminate. To turn
the system off, push the ON/OFF button a second
time. The Cruise Indicator Light will turn off. The
system should be turned off when not in use.
WARNING!
Leaving the Electronic Speed Control sys-
tem on when not in use is dangerous. You
could accidentally set the system or cause it
to go faster than you want. You could lose
control and have an accident. Always leave
the system OFF when you are not using it.
Electronic Speed Control Buttons
1 — ON/OFF
2 — RES +
4 — CANCEL 3 — SET -
11 7

•Unstored Messages Until RUN
These messages deal primarily with the Re-
mote Start feature. This message type is dis-
played until the ignition is in the RUN state.
Examples of this message type are "Remote
Start Aborted - Door Ajar" and"Press Brake
Pedal and Push Button to Start".
• Five Second Unstored Messages
When the appropriate conditions occur, this
type of message takes control of the main
display area for five seconds and then returns to
the previous screen. Examples of this message
type are "Memory System Unavailable - Not in
Park" and"Automatic High Beams On".
The Reconfigurable Telltales section is divided
into the white telltales area on the right, amber
telltales in the middle, and red telltales on the left.
When the appropriate conditions exist, the
EVIC displays the following messages:
•Vehicle Not In Park
• Key Left Vehicle
• Key Not Detected •
Service Keyless System
• Service Tire Pressure System
• Service Park Assist System
• Park Assist System Blinded
• Park Assist Disabled
• Front Sensor Blinded
• Rear Sensor Blinded
• Keyfob Battery Low
• Liftglass Open
• Left Front Turn Signal Lamp Out
• Right Front Turn Signal Lamp Out
• Left Rear Turn Signal Lamp Out
• Right Rear Turn Signal Lamp Out
• Check Tire Pressure
• ESC System Off
• Service Blind Spot System
• Blind Spot Detection Unavailable
• Blind Spot System Off •
Blind Spot System Unavailable Sensor
Blocked
• Blind Spot System Unavailable Astronomy
Zone — When the Blind Spot Module senses
a tower on the same frequency that it is
interfering with, it will automatically turn the
Blind Spot System off.
• Normal Cruise Ready — When Adaptive
Cruise Control (ACC) system is turned off
and Normal (Fixed Speed) Cruise Control
mode is available. Refer to “Adaptive Cruise
Control (ACC)” in “Understanding The Fea-
tures Of Your Vehicle” (if equipped).
• Adaptive Cruise Off — When the Adaptive
Cruise Control (ACC) system is turned off.
Refer to “Adaptive Cruise Control (ACC)” in
“Understanding The Features Of Your Ve-
hicle” (if equipped).
• ACC Ready — When the ACC system is
activated. Refer to “Adaptive Cruise Control
(ACC)” in “Understanding The Features Of
Your Vehicle” (if equipped).
170

1. Power – Turns the screen and wireless
headphone transmitter for the selected Channel
on or off. To hear audio while the screen is
closed, press the Power button to turn the
headphone transmitter on.
2. Channel Selector Indicators – When a but-
ton is pressed, the currently affected channel or
channel button is illuminated momentarily.
3. Light – Turns the remote control backlighting
on or off. The remote backlighting turns off
automatically after five seconds.4. Channel/Screen Selector Switch - Indicates
which channel is being controlled by the remote
control. When the selector switch is in the
Channel 1 position, the remote controls the
functionality of headphone Channel 1 (right side
of the screen). When the selector switch is in
the Channel 2, position the remote controls the
functionality of headphone Channel 2 (left side
of the screen).
5.
 – In radio modes, press to seek the next
tunable station. In disc modes, press and hold
to fast forward through the current audio track
or video chapter. In menu modes use to navi-
gate in the menu.
6. / Prev – In radio modes, press to select to
the previous station. In disc modes, press to
advance to the start of the current or previous
audio track or video chapter. In menu modes,
use to navigate in the menu.
7. MENU – Press to return to the main menu of
a DVD disc, to select a satellite audio channel
from the Station list, or select playback modes
(RANDOM for a CD).
8. / (Play/Pause) – Begin/resume or pause
disc play. 9.
■(Stop) – Stops disc play
10. PROG Up/Down – When listening to a
radio mode, pressing PROG Up selects the
next preset and pressing PROG Down selects
the previous preset stored in the radio. When
listening to compressed audio on a data disc,
PROG Up selects the next directory and PROG
Down selects the previous directory. When lis-
tening to a disc in a radio with a multiple-disc
changer, PROG Up selects the next disc and
PROG Down selects the previous disc.
11. MUTE – Press to mute the headphone
audio output for the selected channel.
12. SLOW – Press to slow playback of a DVD
disc. Press play () to resume normal play.
13. STATUS – Press to display the current
status.
14. MODE – Press to change the mode of the
selected channel. See the Mode Selection sec-
tion of this manual for details on changing
modes.
Remote Control
198

Keyless Enter-N-Go™
This feature allows the
driver to operate the igni-
tion switch with the push
of a button, as long as
the ENGINE START/
STOP button is installed
and the Remote Start/
Keyless Enter-N-Go™
FOBIK is in the passenger
compartment.
Installing And Removing The ENGINE
START/STOP Button
Installing The Button
1. Remove the key fob from the ignition switch.
2. Insert the ENGINE START/STOP button into
the ignition switch with the lettering facing up
and readable.
3. Press firmly on the center of the button to
secure it into position.Removing The Button
1.
The ENGINE START/STOP button can be
removed from the ignition switch for key fob use.
2. Insert the metal part of the emergency key
under the chrome bezel at the 6 o’clock position
and gently pry the button loose.
NOTE:
The ENGINE START/STOP button should
only be removed or inserted with the ignition
in the OFF position (OFF position for Key-
less Enter-N-Go™).
Normal Starting
Using The ENGINE START/STOP Button
1. The transmission must be in PARK or NEU-
TRAL.
2. Press and hold the brake pedal while press-
ing the ENGINE START/STOP button once.
3. The system takes over and attempts to start
the vehicle. If the vehicle fails to start, the starter
will disengage automatically after 10 seconds. 4. If you wish to stop the cranking of the engine
prior to the engine starting, press the button
again.
NOTE:
Normal starting of either a cold or a warm
engine is obtained without pumping or
pressing the accelerator pedal.
To Turn Off The Engine Using ENGINE
START/STOP Button
1. Place the shift lever in PARK, then press and
release the ENGINE START/STOP button.
2. The ignition switch will return to the OFF
position.
3. If the shift lever is not in PARK, the ENGINE
START/STOP button must be held for two sec-
onds and vehicle speed must be above 5 mph
(8 km/h) before the engine will shut off. The
ignition switch position will remain in the ACC
position until the shift lever is in PARK and the
button is pressed twice to the OFF position.
221

3. Lower the vehicle to the ground by turning
the jack handle counterclockwise.
4. Finish tightening the lug nuts. Push down on
the wrench while at the end of the handle for
increased leverage. Tighten the lug nuts in a
star pattern until each nut has been tightened
twice. The correct tightness of each lug nut is
110 ft-lbs (150 N·m). If in doubt about the
correct tightness, have them checked with a
torque wrench by your authorized dealer or
service station.
5. After 25 miles (40 km) check the lug nut
torque with a torque wrench to ensure that all
lug nuts are properly seated against the wheel.
JUMP-STARTING
If your vehicle has a discharged battery it can be
jump-started using a set of jumper cables and a
battery in another vehicle or by using a portable
battery booster pack. Jump-starting can be dan-
gerous if done improperly so please follow the
procedures in this section carefully.NOTE:
When using a portable battery booster pack
follow the manufacturer’s operating instruc-
tions and precautions.
CAUTION!
Do not use a portable battery booster pack or
any other booster source with a system
voltage greater than 12 Volts or damage to
the battery, starter motor, alternator or elec-
trical system may occur.
WARNING!
Do not attempt jump-starting if the battery is
frozen. It could rupture or explode and cause
personal injury.
Preparations For Jump-StartThe battery in your vehicle is located under the
passenger’s front seat. There are remote loca-
tions located under the hood to assist in jump-
starting.
Remote Battery Posts
1 — Remote Positive
(+)Post (covered with
protective cap)
2 — Remote Negative (-)Post
300

WARNING!
•Take care to avoid the radiator cooling fan
whenever the hood is raised. It can start
anytime the ignition switch is ON. You can
be injured by moving fan blades.
• Remove any metal jewelry such as rings,
watch bands and bracelets that could
make an inadvertent electrical contact.
You could be seriously injured.
• Batteries contain sulfuric acid that can
burn your skin or eyes and generate hy-
drogen gas which is flammable and explo-
sive. Keep open flames or sparks away
from the battery.
NOTE:
Be sure that the disconnected ends of the
cables do not touch while still connected to
the other vehicle.
1. Set the parking brake, shift the automatic
transmission into PARK and turn the ignition to
LOCK. 2. Turn off the heater, radio, and all unneces-
sary electrical accessories.
3. Remove the protective cover over the re-
mote positive
(+)battery post. Pull upward on
the cover to remove it.
4. If using another vehicle to jump-start the
battery, park the vehicle within the jumper
cables reach, set the parking brake and make
sure the ignition is OFF.
WARNING!
Do not allow vehicles to touch each other as
this could establish a ground connection and
personal injury could result.
Jump-Starting Procedure
WARNING!
Failure to follow this procedure could result
in personal injury or property damage due to
battery explosion.
CAUTION!
Failure to follow these procedures could re-
sult in damage to the charging system of the
booster vehicle or the discharged vehicle.
NOTE:
Make sure at all times that unused ends of
jumper cables are not contacting each other
or either vehicle while making connections.
1. Connect the positive (+)end of the jumper
cable to the remote positive (+)post of the
discharged vehicle.
2. Connect the opposite end of the positive (+)
jumper cable to the positive (+)post of the
booster battery.
3. Connect the negative end (-)of the jumper
cable to the negative (-)post of the booster
battery.
4. Connect the opposite end of the negative (-)
jumper cable to the remote negative (-)post of
the vehicle with the discharged battery.
301

WARNING!
Do not connect the cable to the negative
post(-)of the discharged battery. The result-
ing electrical spark could cause the battery to
explode and could result in personal injury.
5. Start the engine in the vehicle that has the
booster battery, let the engine idle a few min-
utes, and then start the engine in the vehicle
with the discharged battery.
Once the engine is started, remove the jumper
cables in the reverse sequence:
6. Disconnect the negative (-)jumper cable
from the remote negative (-)post of the dis-
charged vehicle.
7. Disconnect the negative end (-)of the
jumper cable from the negative (-)post of the
booster battery.
8. Disconnect the opposite end of the positive
(+) jumper cable from the positive (+)post of the
booster battery. 9. Disconnect the positive
(+)end of the jumper
cable from the remote positive (+)post of the
discharged vehicle.
10. Reinstall the protective cover over the re-
mote positive (+)battery post of the discharged
vehicle.
If frequent jump-starting is required to start your
vehicle you should have the battery and charg-
ing system tested at your authorized dealer.
CAUTION!
Accessories plugged into the vehicle power
outlets draw power from the vehicle’s bat-
tery, even when not in use (i.e., cellular
phones, etc.). Eventually, if plugged in long
enough without engine operation, the vehi-
cle’s battery will discharge sufficiently to de-
grade battery life and/or prevent the engine
from starting.
FREEING A STUCK VEHICLE
If your vehicle becomes stuck in mud, sand or
snow, it can often be moved using a rocking
motion. Turn the steering wheel right and left to
clear the area around the front wheels. Press
and hold the lock button on the shift lever. Then
shift back and forth between DRIVE and RE-
VERSE while gently pressing the accelerator.
NOTE:
Shifts between DRIVE and REVERSE can
only be achieved at wheel speeds of 5 mph
or less. Whenever the transmission remains
in NEUTRAL for more than 2 seconds, you
must press the brake pedal to engage DRIVE
or REVERSE.
Use the least amount of accelerator pedal pres-
sure that will maintain the rocking motion with-
out spinning the wheels or racing the engine.
302

Center High Mounted Stop Light......339
Chains, Tire ................. .265
Checking Your Vehicle For Safety ......59
Checks, Safety .................59
Child Restraint ........50, 53, 54, 55, 56
Child Restraint Tether Anchors ......54, 55
Child Safety Locks ...............23
Clean Air Gasoline ..............274
Cleaning Wheels ................. .329
Climate Control ................209
Cold Weather Operation ...........222
Compact Disc (CD) Maintenance ......208
Compact Spare Tire .............262
Compass ...................182
Compass Calibration .............184
Compass Variance ..............182
Computer, Trip/Travel ............179
Connector UCI ................... .189
Universal Consumer Interface (UCI) . .189
Conserving Fuel ...............178
Console, Overhead ..............140
Coolant Pressure Cap (Radiator Cap) . . .323
Cooling System ................321
Adding Coolant (Antifreeze) ......322
Coolant Capacity ............340 Coolant Level
..............323
Disposal of Used Coolant ........323
Drain, Flush, and Refill .........321
Inspection .............321, 323
Points to Remember ..........324
Pressure Cap ..............323
Radiator Cap ...............323
Selection of Coolant
(Antifreeze) .............322, 340
Cruise Control (Speed Control) .......119
Cupholders ................. .149
Customer Assistance .............372
Data Recorder, Event .............49
Daytime Running Lights..........

.108
Defroster, Rear Window ...........154
Defroster, Windshield ..........60, 212
Diesel Fuel ................. .275
Diesel Fuel Requirements ..........275
Dipsticks Automatic Transmission .........327
Oil (Engine) ...............313
Power Steering .............250
Disabled Vehicle Towing ...........304
Disposal Antifreeze (Engine Coolant) ......323
Door Locks ...................21 Door Locks, Automatic
............22
Driving .................... .244
Off-Pavement ..............245
Off-Road .................245
Driving to Achieve Maximum Fuel Economy ................. .178
Electrical Outlet, Auxiliary (Power Outlet) ...............146
Electric Rear Window Defrost ........154
Electric Remote Mirrors ............71
Electronic Brake Control System ......252
Brake Assist System ..........252
Electronic Roll Mitigation (ERM) ......253
Electronic Speed Control (Cruise Control) ...........117,119
Electronic Stability Control (ESC) ......253
Electronic Vehicle Information Center (EVIC) ............164, 168
Emergency, In Case of Freeing Vehicle When Stuck ......302
Hazard Warning Flasher ........294
Jump Starting ..............300
Engine Air Cleaner ................315
Break-In Recommendations .......59
Compartment .........309, 310, 311
395