2013 INFINITI JX brake

2
new system features
Remote Engine Start* (if so equipped)
your INfINITI Intelligent Key™ system allows the engine to start from
outside your vehicle. To use the remote start feature, perform the following:

1. Aim the INfINITI Intelligent Key at the vehicle. Operating range
is approximately 197 feet (60 m) from the vehicle.
2. Press the

button
01 to lock all doors.

3. Within 5 seconds press and hold the remote start

button
02
until the turn signal lights illuminate. If the vehicle is not within

view, press and hold the remote start button for about 2 seconds.

The parking lights will turn on and remain on as long as the engine
is running. The doors will be locked and the climate control system
may come on.

Repeat steps 1 - 3 to extend time an additional 10 minutes. A maximum of two remote starts,
or a single start with an extension, are allowed between ignition cycles.


Depress the brake and place the ignition switch in the ON position before driving.

To cancel a remote start, perform one of the following:
•
Aim the Intelligent Key at the vehicle and press and hold the

button until the parking
lights turn off.
•
Turn the hazard warning flashers on.
•
Cycle the ignition switch ON and then OFF.
*Laws in some communities may restrict the use of remote starters. Check local regulations before using this feature.
for more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
INFINITI Connection™ System* (if so equipped)
Infiniti Connection provides various types of information
and services by connecting your vehicle to the Infiniti
Connection Data Center. f or more details on the Infiniti
Connection service, terms and conditions, please refer
to www.Infiniticonnection.com.
Available services include:

Infiniti Personal Assistant – To access Infiniti Personal
Assistant, select “Connect to Voice Menu” from the Infiniti Connection menu or touch the


key (if available on the map screen). At the voice prompt, say “Infiniti Personal Assistant” to
be connected.
• your Infiniti Personal Assistant can send destination information directly to your vehicle.
To access, go to the Infiniti Connection menu and select “Sync All Information f eeds”.
Then go to the feeds menu page and download the desired destination information.

Automatic Collision Notification – In case of air bag deployment, a signal is sent containing
the vehicle location and customer information and notifies the proper authorities.
01
02
*Infiniti Connection™ is only available on vehicles equipped with optional Infiniti Connection™ subscription service.

essential information
Loose Fuel Cap
A LOOSE FUEL CAP warning message will appear
in the vehicle information display

01 when the
fuel-filler cap is not tightened correctly.

To tighten, turn the cap clockwise until a single click
is heard.

The warning message will disappear when the vehicle
detects the fuel-filler cap is properly tightened and the
reset button

02 is pressed for about 1 second.

If the cap is not properly tightened, the Malfunction
Indicator Light

may illuminate.
f
or more information, refer to the “Instruments and controls (section 2)”
and the “Pre-driving checks and adjustments (section 3)” of your
Owner’s Manual.
Tire Pressure Monitoring System (TPMS) with Tire Inflation Indicator
A Tire Pressure Low - Add Air warning message will
appear in the vehicle information display

01 and the

low tire pressure warning light
02 will illuminate when

one or more tires are low on pressure and air is needed.
• The tire pressures should be checked when the
tires are cold. The tires are considered cold after
the vehicle has been parked for 3 hours or more or
driven less than 1 mile (1.6km) at moderate speeds.

When adding air to an under-inflated tire, the TPMS
with Tire Inflation Indicator provides visual and
audible signals to help you inflate the tires to the
recommended COLD tire pressure.
To use the tire inflation indicator:
1. Move the shift lever to the P (PARK) position and apply the parking brake.
2. Place the ignition switch in the ON position. Do not start the engine.
3. Add air to the under-inflated tire and within a few seconds, the hazard warning lights will start
flashing.
4. When the designated tire pressure is reached, the horn will beep once and the hazard warning
flashers will stop flashing.
5. Repeat this procedure for any additional under-inflated tires.

After tire pressures are adjusted, drive the vehicle at speeds above 16 MPH (25km/h). The
Tire Pressure Low - Add Air warning message and low tire pressure warning light will disappear.

When the low tire pressure warning light flashes for approximately 1 minute and then remains
on, the TPMS is not functioning properly. Have the system checked by an INfINITI retailer.
01
01
02
7
02

10
first drive features
INTELLIGENT KEy BATTERy DISCHARGE

If the battery of the Intelligent Key is discharged, or
environmental conditions interfere with the Intelligent
Key operation, start the engine according to the
following procedure:
1. Move the shift lever to the P (P ARK) position.
2. firmly apply the foot brake.
3. Touch the ignition switch with the Intelligent Key
and a chime will sound.
4. Within 10 seconds after the chime sounds, push the ignition switch while depressing the
brake pedal and the engine will start.
for more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and driving (section 5)” and the
“Maintenance and do-it yourself (section 8)” of your Owner’s Manual.
Power Liftgate
When the liftgate is closed and locked, the liftgate will
open automatically by:
• Pushing the power liftgate switch

01 on the
instrument panel.
• Pushing the liftgate request switch

02.
• Pressing the

button
03 on the INfINITI
Intelligent Key™ for more than 0.5 seconds.

To open the liftgate with the liftgate opener switch

04, the liftgate must be unlocked.

The power liftgate operation can be turned on or off
by the power liftgate main switch

05 on the instrument
panel.

When the power liftgate main switch
is pushed to the OFF position, power
operation is not available using the
power liftgate switch on the liftgate


06 or the liftgate opener switch 04.
f
or more information, refer to the “Pre-driving checks
and adjustments (section 3)” of your Owner’s Manual.
0501
0204
0603

13
REVERSE TILT-DOWN fEATURE (if so equipped)


The reverse tilt-down feature will turn the selected outside mirror surface downward to provide
better rear visibility close to the vehicle.
1. Set the parking brake.
2. Push the ignition switch to the ON position.
3. Move the shift lever to the R (REVERSE) position.
4. Choose the right or left outside mirror by operating the outside mirror control switch

01 .
5. The outside mirror surfaces move downward.

The outside mirror surfaces will return to their original positions when one of the following
conditions has occurred:
• The shift lever is moved to any position other than R (REVERSE).
• The outside mirror control switch is set to the center “neutral” position.
• The ignition switch is pushed to the OFF position.
for more information, refer to the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Starting/Stopping the Engine

Depress the brake pedal.

Press the ignition switch START/STOP button to
start the engine.
NOTE: It is important to make sure the INfINITI Intelligent
Key
™ is with you (that is, in your pocket or purse).
TURNING THE ENGINE OFF

Move the shift lever to the P (PARK) position and
apply the parking brake.

Press the ignition switch START/STOP button to turn the engine off.
EMERGENCy ENGINE SHUT Off
To shut off the engine in an emergency situation while driving, perform one of the following procedures:

Rapidly push the push button ignition switch 3 consecutive times, in less than 1.5 seconds, or

Push and hold the push button ignition switch for more than 2 seconds.
for more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.

19
USB/iPod® Interface
The USB jack
01 is located in the center console under

the arm rest.

When a compatible USB memory device or iPod®
is plugged into the USB jack
, compatible

audio and video files stored on the device can
be played through the vehicle’s audio system
and front display.
for more information, refer to the “Monitor, climate, audio, phone and voice
recognition systems (section 4)” of your Owner’s Manual.
Conventional (Fixed Speed) Cruise Control
The cruise control system enables you to set a constant
cruising speed once the vehicle has reached 25 mph.

The system will automatically maintain the set speed
until you tap the brake pedal, accelerate, cancel or
turn the system off.

To activate the cruise control, push the
CRUISE

ON/OFF switch

01 . The
CRUISE
indicator light in
the instrument panel will illuminate.

To set cruising speed, accelerate the vehicle to the
desired speed, push the COAST/SET switch

02
and release. The
SET
indicator light
in the instrument panel will illuminate. Take your foot off
the accelerator pedal. your vehicle will maintain the set speed.

To reset at a faster cruising speed, push and hold the ACCEL/RES switch
03 . When the

vehicle attains the desired speed, release the switch.

To reset at a slower cruising speed, push and hold the COAST/SET switch
02 . Release the

switch when the vehicle slows to the desired speed.
01
02
03
04
01
04 STATION PRESET BUTTONS


Twelve stations can be set for the fM band, six for the AM band and eighteen for XM
satellite radio.

To store a station in a preset, you must first select a radio band by pressing the FM•AM
05
or
XM
06 button, then tune to the desired AM, fM or XM satellite radio station.


Then press and hold the desired station preset button (1-6) until the preset number is
updated on the display and the sound is briefly muted. The channel indicator will then
display and the sound will resume. Programming is now complete.

To retrieve a previously set station, select the radio band where the preset was stored then
press the corresponding station select button (1-6).
for more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (section 4)” of your Owner’s Manual.

20
first drive features
Intelligent Cruise Control (ICC) System (if so equipped)
VEHICLE-TO-VEHICLE DISTANCE CONTROL MODE

To set Vehicle-To-Vehicle Distance Control mode,
press the CRUISE ON/OFF button

01 for less than 1.5
seconds. The CRUISE indicator light
02 will illuminate.

Accelerate to the desired speed.

Push down on the COAST/SET switch
03 and release
it. Cruise control will be set to the desired speed.

Press the distance button
04 repeatedly to change
the set distance between long, middle, and short.

When a vehicle is not detected ahead of you in the
lane, the set distance and set vehicle speed indicator
lights will illuminate

05 in set mode.

When a vehicle is detected ahead of you in the lane,
the vehicle ahead detection, set distance, and set
vehicle speed indicator lights will illuminate

06 in set mode.

To reset at a faster cruising speed, push and hold the ACCEL/RES
switch

07 . When the vehicle attains the desired speed, release the switch.

To reset at a slower cruising speed, push and hold the COAST/SET switch


03 . Release the switch when the vehicle slows to the desired speed.

To cancel the preset speed, push the CANCEL switch
08 or tap the brake pedal. The set
vehicle speed indicator
05 will go out.

To turn off cruise control, press the CRUISE ON/OFF button
01 . The
CRUISE indicator light

02 , in the instrument panel, will turn off.
To set conventional (fixed speed) cruise control mode:

While cruise control is off, press the CRUISE ON/OFF
button
01 and hold it down for more
than 1.5 seconds. The CRUISE indicator light will illuminate.

Accelerate to the desired speed.

Push down on the COAST/SET switch and release it. The SET indicator light will illuminate.
Cruise control will be set to the desired speed.
To switch between the two cruise control modes:

When one of the two cruise modes is in use, you must turn the system off, and then turn it on
again to select the other cruise control mode.
for more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
01
0403
0708
0205
06

To cancel the preset speed, push the CANCEL switch
04 .

To turn off cruise control, push the CRUISE
ON/OFF switch
01 . Both the
CRUISE indicator

light
and the SET
indicator light in the instrument panel will turn off.
for more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.

29
Theater Package (if so equipped)
With this Entertainment System, you can play video
files via a DVD or CD providing images and sound
both from the front and rear display screens.

you can also connect auxiliary devices such as video
games, camcorders or portable video players to the
auxiliary jacks

01 located on the back of the center
console. (y our device will be controlled through its
own control panel.)

Rear Auxiliary Mode allows rear seat passengers to
independently display different sources on each
screen.

Use the remote controller
02 , provided with the

system, to operate the rear display screens.

Use the headphones
03 , also provided with

the system, to listen to audio wirelessly and
independently. you may also connect your own
wired-headphones to the headphone jacks

04
located on the back of the center console.


for optimum performance, select the appropriate
headphone channel

05 that corresponds to the
headrest display being viewed directly in front of you.

To view movies on the front display, stop the vehicle in
a safe location, move the shift lever to the P (PARK)
position and apply the parking brake.

To reduce driver distraction, the wireless headphones will not operate
while located in the front seats and movies will not be shown on the
front display while the vehicle is in any drive position.
for more information, refer to the “Monitor, climate, audio, phone and voice recognition systems
(section 4)” of your Owner’s Manual.
08 STATUS
– Press multiple times to display audio information, the air conditioner status, fuel
economy or navigation directions.
09 – Press to switch between the day screen (bright) and the night screen (dark). Press and
hold the button to turn the display off. Press again to turn the display on.
10 BACK – Press to return to the previous screen. In a settings screen, this button can also be
used to apply the setting. In a character input screen, this button can also delete the characters
that have been entered.
11 VOICE – Press to hear the current voice guidance for a programmed route.

for more information, please refer to your Navigation System Owner’s Manual.
05
04
01
02
03