2013 FORD MUSTANG buttons

When you select: You can:
H.
TUNE/OK/Play/PauseIn radio mode,TUNE allows you to scan the
frequency band in individual increments.
In SIRIUS mode,TUNE allows you to find
the next or previous available SIRIUS
satellite station.
OKallows you to confirm commands with
special phone and media features. If your
vehicle is equipped with SYNC, refer to the
SYNC chapter for more information.
Play/Pauseallows you to play or pause a
track when listening to a CD.
I. AUX Access Line In (auxiliary audio mode) and
SYNC. If your vehicle is equipped with
SYNC, refer to the SYNC chapter for more
information.
J. CD Press the CD button to access CD/MP3 mode.
The CD/MP3 begin to play where it left off. If
no CD is loaded, NO DISC appears in the
display.
Press the seek buttons to access the previous
or next track. Press and hold the seek buttons
to quickly reverse or advance within the same
track.
K. SIRIUS Access SIRIUS satellite radio mode. Press
repeatedly to cycle through SAT1, SAT2 and
SAT3.
Note:SIRIUSsatellite radio is available only
with a valid SIRIUSradio subscription. Check
with your authorized dealer for availability.
L. AM/FM Select AM, FM1 or FM2.
M. On/Off/VOL Press the power control to turn the system on
and off.
Turn to adjust the volume.
N. LOAD This control is not operational. To load a CD,
insert the disc, label side up, into the CD slot.
122Audio System
2013 05+ Mustang(197)
Owners Guide gf, 1st Printing
USA(fus)

When you select: You can:
O. CAT/FOLDIn SIRIUS mode,switch between turning the
most recently selected satellite radio category
on or off.
In MP3 mode,use the SEEK buttons to
access the previous or next folder.
P. SCANIn radio mode,hear a brief sampling of all
radio stations.
In SIRIUS mode,hear a brief sampling of all
available channels. If a specific category is
selected, press SCAN for a brief sampling of
all available channels within the selected
category.
In CD/MP3 mode,hear a brief sampling of
all tracks on the current disc or MP3 folder.
Q. DIRECTIn radio mode,select the desired radio
frequency (i.e. 93.9) using the memory preset
numbers (0–9).
In SIRIUS mode,enter the desired channel
(i.e. 002) using the memory preset buttons. If
you only enter one digit, press OK and the
system goes to that channel. If you enter
three digits, the system automatically goes to
that channel, if available. You may cancel your
entry by pressing DIRECT. If an invalid station
number is entered, INVALID CHANNEL
appears in the display and the system
continues playing the current station.
In CD mode,enter the desired track number
using the memory preset buttons (0–9). The
system then begins playing that track.
In MP3 mode,enter a memory preset button
of the desired folder. The system advances to
that specific folder.
Audio System123
2013 05+ Mustang(197)
Owners Guide gf, 1st Printing
USA(fus)

When you select: You can:
R. TEXTIn MP3 mode,allows you to view Album
(AL), Folder (FL), Song (SO) and Artist (AR)
in the display, if available.
Note:In text mode, sometimes the display
requires additional text to be displayed. When
theindicatorison,pressTEXT and
then use the SEEK buttons to view the
additional display text.
S. SEEKIn radio mode,select a frequency band and
press one of the seek buttons. The system
stops at the first station it finds in that
direction.
In SIRIUS mode,select the previous or next
channel. If a specific category is selected,
(Jazz, Rock, News, etc.), use the SEEK
buttons find to the previous or next channel
in the selected category.
In CD/MP3 mode,select the previous or
next track.
AUXILIARY INPUT JACK
WARNING:Driving while distracted can result in loss of vehicle
control, accident and injury. Ford strongly recommends that you
use extreme caution when using any device or feature that may take
your focus off the road. Your primary responsibility is the safe operation
of the vehicle. We recommend against the use of any handheld device
while driving, encourage the use of voice-operated systems when
possible and that you become aware of applicable state and local laws
that may affect use of electronic devices while driving.
WARNING:For safety reasons, do not connect or adjust the
settings on your portable music player while the vehicle is
moving.
124Audio System
2013 05+ Mustang(197)
Owners Guide gf, 1st Printing
USA(fus)

CAR2UHOME AUTOMATION SYSTEM (IF EQUIPPED)
WARNING:Make sure that the garage door and security device
are free from obstruction when you are programming. Do not
program the system with the vehicle in the garage.
WARNING:Do not use the system with any garage door opener
that does not have the safety stop and reverse feature as required
by U.S. Federal Safety Standards (this includes any garage door opener
manufactured before April 1, 1982).
Note:Make sure you keep the original remote control transmitter for use
in other vehicles as well as for future system programming.
Note:We recommend that upon the sale or lease termination of your
vehicle, you erase the programmed function buttons for security reasons.
SeeErasing the function button codeslater in this section.
Note:You can program a maximum of three devices. To change or
replace any of the three devices after it has been initially programmed,
you must first erase the current settings. SeeErasing the function
button codeslater in this section.
Note:Programming the system to a community gate will require a
unique set of instructions depending on the gate system model. Contact
the help line on 1-866-572-2728 for further information.
Note:If you accidently enter the program mode by pressing and
releasing the outer two buttons or all three buttons simultaneously, do
not press any button until the module times out after a few seconds and
resets to normal mode. When the module has timed out, all three LED
lamps will flash rapidly for a few seconds then turn off. Any settings
should remain as previously set.
The universal garage door opener
replaces the common hand-held
garage door opener with a
three-button transmitter that is
integrated into the driver’s sun visor.
146Universal Garage Door Opener
2013 05+ Mustang(197)
Owners Guide gf, 1st Printing
USA(fus)

The system includes two primary features, a garage door opener and a
platform for remote activation of devices with the home. As well as being
programmed for garage doors, the system transmitter can be
programmed to operate security devices and home lighting systems.
Additional system information can be found on-line at www.learcar2U.com
or by calling the toll-free help line on 1-866-572-2728.
Rolling code programming
Note:If you do not follow the time-sensitive instructions, the device will
time out and you will have to repeat the complete procedure.
Note:It may be helpful to have another person assist you in
programming the transmitter.
1. Switch the ignition on.
2. Press and hold the outer two
buttons for 1–2 seconds, then
release.
Note:You may need a ladder to
reach the unit and you may need to
remove the cover or lamp lens.
Note:If you cannot locate the learn
button, refer to the Owner Manual
of your garage door opener or call
the toll-free help line on
1-866-572-2728.
3. Press the learn button on the
garage door opener motor.
Note:You will have 10–30 seconds
to complete the following steps.
4. Return to your car.
5. Press and hold the function
button you would like to use to
control the garage door. You may
need to hold the button from
5–20 seconds, during which time the selected button LED lamp will flash
slowly.
6. When the garage door moves, release the button within one second.
The LED lamp will flash rapidly until programming is complete.
Universal Garage Door Opener147
2013 05+ Mustang(197)
Owners Guide gf, 1st Printing
USA(fus)

7. Press and release the button again. The garage door should move,
confirming that programming is successful. If your garage door does not
operate, repeat the previous steps.
The LED lamp above the selected button will illuminate to confirm that
the system is responding to the button command.
To program another rolling code device, repeat steps one through six
substituting a different function button in step four.
Fixed code programming
Note:It may be helpful to have another person assist you in
programming the transmitter.
To program units with fixed code
DIP switches, you will need the
garage door hand-held transmitter,
paper and a pen or pencil.
1. Switch the ignition on.
2. Open the battery cover and note all the switch settings from left to
right.
When the switch is in the up, on, or + position, mark down “left button”.
When the switch is in the middle, neutral, or 0 position, mark down
“middle button”.
When the switch is in the down, off, or – position, mark down “right
button”.
3. Press all three function buttons
simultaneously for a few seconds
and then release. The LED lamps
will flash slowly.
Note:The following step must be
completed within 2.5 minutes.
4. Enter the corresponding DIP switch settings from left to right into the
system by pressing and releasing the buttons corresponding to the
settings you noted.

148Universal Garage Door Opener
2013 05+ Mustang(197)
Owners Guide gf, 1st Printing
USA(fus)

5. Simultaneously press and release all three function buttons. The LED
lamps will illuminate.
6. Press and hold the function
button you would like to use to
control the garage door.
Note:You may need to hold the
button from 5–55 seconds before
observing movement of the garage
door.
7. When the garage door moves, release the button within one second.
When the button is released, the LED lamp will flash slowly.
8. The LED lamp will begin to flash rapidly until programming is
complete. If your garage door does not operate, repeat the previous
steps. Otherwise, call the toll-free help line on 1-866-572-2728.
The LED lamp above the selected button will illuminate to confirm that
the system is responding to the button command.
Erasing the function button codes
Note:You cannot erase individual
buttons.
1. Press and hold the outer two
function buttons simultaneously for
approximately 20 seconds until the
LED lamps above the buttons flash
rapidly.
2. When the LED lamps flash, release the buttons. The codes for all
buttons are erased.
FCC and RSS-210 Industry Canada Compliance
This device complies with Part 15 of the FCC Rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
Changes or modifications to your device not expressly approved by the
party responsible for compliance can void the user’s authority to operate
the equipment.
Universal Garage Door Opener149
2013 05+ Mustang(197)
Owners Guide gf, 1st Printing
USA(fus)

“DIAL”
“Plus”
“Star”
Note:To exit dial mode, press and hold the phone button or press
MENU to go to the PHONE menu.
At any time, you can say the following global commands:
GLOBAL COMMANDS
“Exit”
“Help”
“Phone”
“ Services”
*
“Vehicle Health Report”*
“Voice settings”
*If equipped, U.S. only
Making Calls Using the Touchscreen
Press the PHONE hard button, then choose between three ways to make
a call:
1. Use the keypad on the Phone tab to manually enter a phone number
and press SEND.
2. Select the Phonebook tab (if the desired number is saved in the
downloaded phone book information). Use the directory buttons to
browse to the desired contact, then press DIAL. (This is a
phone-dependent feature.)
3. Select the Call History tab (if the desired number is saved in the
downloaded call history information), then press DIAL. (This is a
phone-dependent feature.)
Making Calls Using Voice Commands
Press the voice button and when prompted say “Phone”.
1. Say “Call ” or “Dial”, then the desired
number.
2. When the system confirms the number, say “Dial” or “Call” to initiate
the call.
To erase the last spoken digit, say “Delete”; to erase all spoken digits, say
“Clear”.
To end the call, press and hold the phone button.
328SYNC
2013 05+ Mustang(197)
Owners Guide gf, 1st Printing
USA(fus)