2013 FORD F150 mirror

14 POWER-
aDJUSTaBLE FOOT PED aLS
Located on the left-hand side of your
steering column, your power-adjustable
pedal control lets you move your brake
and accelerator pedals closer. Press the
arrow to move the pedals closer to you
or the arrow to move the pedals further
away from you. The pedals should only be
adjusted when the vehicle is stopped and
in Park (P).
MYKEY
®
MyKey allows you to program certain
driving restrictions in order to promote
good driving habits. You can program
things such as speed restrictions,
limited volume levels. For complete
information, refer to the MyKey chapter
in your Owner’s Manual.MEMORY FEATURE*
The memory function allows a “one touch”
recall of personalized memory features
(i.e., the positions of the driver seat, power
mirrors and power-adjustable foot pedals).
Use the memory controls, located on the
side of the driver’s seat
, to program
and then recall memory positions. To program position 1, press and hold the
1 button
until you hear a chime. Use
this same procedure to set the second
position using the 2 button
. You can
now use these controls to recall the set
memory positions.
REMOTE ENTRY SYSTEM FEATURES*
Press
once to unlock the driver’s door.
Press
twice to unlock the passenger
and rear doors.
Press
once to lock all the doors.
Press
twice to confirm all the doors are
closed and locked.
Press
to activate the panic alarm.
Press again or turn the ignition on to
deactivate the panic alarm.
Car finder: Press
twice within three
seconds. The horn will chirp and the turn
lamps will flash. It is recommended to use
this method to locate your vehicle, rather
than using the panic alarm.
15
HEa TED an D COOLED FROnT SEa TS*
To operate the heated feature, press
to cycle through the various heat
settings and off.
To operate the cooled feature, press
to cycle through the various
cooling settings and off. The cooled seats will function only when the
engine is running.
Note: Higher settings are indicated by more indicator lights.
REaR HEa TED SEaTS*
The rear-seat heat controls are located on the rear door armrest. To operate
the heated seats, push the right side of the control for maximum heat; p\
ush
the left side of the control for minimum heat. Push again to turn off. T\
he
indicator light will illuminate when the heated seats have been activate\
d.
MOOn ROOF*
Your moonroof is equipped with a one-touch, express opening and
closing feature. To open, press and release the SLIDE control, the
sunscreen will open. To fully open the moonroof, press and release the
SLIDE control again. To close, pull and release the SLIDE control.
Press and release the t I Lt control to vent the moonroof. Pull and
hold the t I Lt control to close the moonroof. The sliding shade can be
manually opened or closed when the moonroof is closed. Pull the shade
toward the front of the vehicle to close it.
aDJUST
aBLE HEaD RESTRainTS
The front head restraints
can be adjusted to suit
your needs. Simply pull
up to raise the head
restraint. To lower, press
the head restraint down
while pressing and holding
the guide sleeve adjust/
release button. You may
also be able to tilt the
head restraint forward or
backward for additional
comfort. Pivot the head
restraint forward to the
desired location. After the head restraint reaches the forward-most tilt
position, pivot it forward again to return it to its standard position.
aMB iE nT Lig HTing*
When activated, the footwell areas, cup holders and center console
bin illuminate with your chosen color. Press
repeatedly to turn the
feature on, cycle through your color options and turn the feature off. P\
ress
the
button to adjust the brightness intensity. In vehicles equipped with
the MyFord Touch 8-inch touch screen, the feature is accessible through
the touch-screen menu. Press the Settings icon, select Vehicle and then
Ambient Lighting. Touch the desired color. Use the scroll bar to increase
or decrease the intensity. To turn the feature off, press the power button.
*if equipped
*if equipped
COnVEniEnCE
COMFORT

your proximity to objects. If equipped with the
navigation system, you can also press Zoom to
zoom in or out.
Note: Visibility aids do not replace the need to
watch where the vehicle is moving. Refer to your
Owner’s Manual for safety information, more
detail and limitations.REVERSE SEnSing S YSTEM*
This system can warn you if there is an object
behind the vehicle. A warning tone will sound
which increases in frequency as the object gets
closer and will sound continuously when the object
is less than 10 inches away. The system is not
effective when the vehicle is traveling above
3 mph (5 km/h) and may not detect angular
or moving objects.
Note: Visibility aids do not replace the need to
watch where the vehicle is moving. Refer to your
Owner’s Manual for safety information, more
detail and limitations.
Hi LL ST aRT aSS iST
Hill start assist helps keep your vehicle stationary
long enough to move your foot from the brake
pedal to the accelerator pedal when your vehicle
is on a slope. The brakes release automatically
once the engine has developed sufficient drive to
prevent the vehicle from rolling down the slope.
To use:
1. Press and hold the brake pedal to bring your
vehicle to a complete standstill.
2. If the sensors detect that the vehicle is on a
slope, the hill start assist feature will be
activated automatically. 3.
When you remove your foot from the brake
pedal, the vehicle will remain on the slope
without rolling away for approximately
two or three seconds. This hold time will
automatically be extended if you are in the
process of driving off.
4. Drive off in a normal manner. The brakes will
be released automatically.
Hi LL DESCE nT COnTROL
Set and maintain your vehicle speed while
descending steep grades in various surface
conditions with hill descent control. This feature
can help you maintain your vehicle speed on
downhill grades between 3 mph (5 km/h) and
20 mph (32 km/h). Above 20 mph (32 km/h),
the system remains armed, but descent speed
cannot be set or maintained.
1. Press and release the hill descent button
located on the instrument panel. A light in the
control will illuminate and a chime will sound
when this feature is activated.
2. To increase descent speed, press the
accelerator pedal until the desired speed is
reached. To decrease descent speed, press the
brake pedal until the desired speed is reached.
For more detailed information, please refer to
your Owner’s Manual.
O VERDR iVE COnTROL WiTH
TOW /Ha UL FEa TURE
This feature helps improve transmission operation
when towing a trailer or a heavy load. To activate
tow/haul, press the button on the side of the
gearshift lever on a floor-shift transmission. The button is located on the end of the

column-shift transmission lever. The toW h AU L
indicator light will illuminate in the instrument cluster.
To deactivate, press the button again. Drive with the
vehicle in D (overdrive) with tow/haul off for the best
fuel economy. Refer to the Transmission chapter of
your Owner’s Manual for more information.
PRO gRESS iVE Rang E SELECTiOn (PRS)
With the gearshift lever in D (Drive), press the
– button on your transmission gearshift lever or
column shifter to activate PRS. The available and
selected gears will be indicated in the instrument
cluster. All available gears will be displayed with the
current gear indicated. Press the – button again
to lock out gears beginning with the highest gear.
Example: press the – button twice to lock out 6th
and 5th gears. Only the available gears will be
displayed and the transmission will automatically
shift between the available gears. Press the +
button to unlock gears to allow the transmission
to shift to higher gears. The transmission will shift
automatically within the gear range you select.
POWERSCOPE
® POWER-FOLD ing, POWER-
aDJUST aBLE TELESCOP ing MiRRORS*
Using the door-mounted switch, you can position
both mirrors at the same time. To telescope the
mirrors out, press and hold the left side of the
switch. While the mirrors extend, it is normal to hear
the telescoping motors running as you hold the
switch. To telescope mirrors in, press and hold the
right side of the switch.
FUNC tIoN
aDV anCETRa C® WiTH ROLL ST aBiL iTY
COnTROL™ (RSC®) ST aBiL iTY
E n HanCEME nT SYSTEM*
The AdvanceTrac
® stability system helps you to
maintain stability and steer-ability of your vehicle
during a variety of road conditions. If your vehicle
becomes stuck in the snow, mud or sand, try
turning off the AdvanceTrac
® system to allow
wheel spin and help increase momentum to dig the
vehicle out. The system can be manually turned off
. Refer to your Stability Control chapter in your
Owner’s Manual for more details.
TRai LER SW aY COnTROL
Your vehicle is equipped with trailer sway control.
This control uses the vehicle’s AdvanceTrac with
RSC system to detect and help reduce trailer sway
by applying brake force at individual wheels and, if
necessary, reducing engine power. If this happens,
tRAILER SWAY REDUCE SPEED will appear
in the information display and the AdvanceTrac icon
will flash briefly. For more information, please
refer to your Owner’s Manual.
TRai LER BRaKE COnTROLLER*
The fully integrated trailer brake controller (TBC)
synchronizes vehicle and trailer brakes for seamless
braking (even with the heaviest loads) to provide
added driving control and confidence. Use the
GAIN adjustment buttons to increase or decrease
the braking feature’s power output to the trailer.
The GAIN setting is used to set the TBC for
specific towing conditions and should be changed
as towing conditions change. Changes to towing
conditions include trailer load, vehicle load, road
conditions and weather. After checking your trailer’s
brakes to make sure they are in good working order
and hooking up your trailer, you can adjust the
GAIN by:
1.
Pressing the GAIN + or GAIN - buttons to
increase or decrease the setting to the desired
starting point. A GAIN setting of 6.0 is a good
starting point for heavier loads.
2. Testing the adjusted GAIN setting again after
you’ve made adjustments. When testing:
a. In a traffic-free environment, tow the trailer
on a dry, level surface at a speed of 20-25
mph (30-40 km/h) and squeeze the manual
control lever completely.
b. If the trailer wheels lock up (the tires will
squeal), reduce the GAIN setting. If the
trailer wheels turn freely, increase the
GAIN setting.
c. The proper GAIN setting will be at the point
just below trailer wheel lock-up
Note: If towing a heavier trailer, trailer wheel lock-
up may not be attainable even with the maximum
GAIN setting of 10. ELECTROniC LOCK
ing DiFFERE nTiaL (ELD)*
With the ELD engaged, the rear axle temporarily
locks, allowing both rear wheels to turn at the
same speed. The function helps to provide
additional traction as needed.
t o activate:
In 4x4 vehicles, pull the 4WD control knob
toward you.
In 4x2 vehicles, turn the ELD control knob from
oFF to oN.
The indicator light
will be continuously
displayed in the cluster when the ELD is active.
Note: ELD should not be used on dry surfaces.
R EaR ViEW CaMERa S YSTEM*
Located under the Ford oval badge on the tailgate,
this camera provides a visual display of the area
behind the vehicle. The display will automatically
appear in the navigation system screen (if
equipped) or in the auto dimming rearview mirror
whenever the vehicle is in R (Reverse) and uses
colors (green, yellow and red) to alert you of *if equipped
*if equipped
16 17