2013 Citroen DS5 engine

)Turn the selector Ato the "air" position.)Uncoil the black pipe Hfully. )Connect the black pipe to the
valve of the wheel.
) Connect the compressor's electric plug to
the vehicle's 12 V socket.) Star t the vehicle again and leave the engine running.

)Adjust the pressure using the compressor (to inflate: switch B
in position "I"
; to deflate: switch B
in position "O"and press button C), in accordance with the vehicle's
tyre pressure label (located on the left hand
door aperture).
A loss of pressure indicates that the
puncture has not been fully plugged; contact a CITROËN dealer or qualified
workshop for assistance.)Remove and stow the kit.
)Drive at reduced speed (50 mph [80 km/h] max) limiting the distance travelled toapproximately 120 miles (200 km).




As soon as possible, go to a CITROËNdealer or a qualified workshop.You must inform the technician that you have used this kit. After inspection, the technician will advise you on whether the tyre can be repaired or if it must be replaced.
2. Infl ation

191Practical information

Removing the cartridge
)Stow the black pipe. )Detach the angled base from the white pipe.)Suppor t the compressor ver tically.)Unscrew the car tridge from the bottom.


Beware of discharges of fluid.
The expiry date of the fluid is indicated on the car tridge.
The sealant car tridge is designed for
single use; even if only partly used, itmust be replaced. After use, do not discard the car tridgeinto the environment, take it to an authorised waste disposal site or a CITROËN dealer.
Do not forget to obtain a new sealantcartridge, available from CITROËN dealers or from a qualified workshop.

Checking tyre pressures /
inflating accessories
You can also use the compressor, withoutinjecting any product, to:
- check or adjust the pressure of your tyres,
- inflate other accessories (balls, bicycle
tyres...).

)
Turn the selector Ato the "Air"
position.
) Uncoil the black pipe H
fully.)
Connect the black pipe to the
valve of the wheel or accessory.
If necessary, fit one of the adaptorssupplied with the kit first.
) Connect the compressor's electrical connector to the vehicle's 12 V socket. )
Star t the vehicle and let the engine run. )
Adjust the pressure using the compressor (to inflate: switch B
in position "I"
; to deflate: switch B
in position "O"and press button C), according to the vehicle's tyrepressure label or the accessory's pressure
label. ) Remove the kit then stow it.

209Practical information

Engine compartment fuses

The fusebox is placed in the engine compartment near the battery.


Access to the fuses
)Unclip the cover. )Change the fuse (see corresponding paragraph).)When you have finished, close the cover carefully to ensure correct sealing of the
f
usebox.


Fuse
N°


Rating(A)Functions
F20 15
Front
/ rear screenwash pump.
F2120 Headlamp wash pump.
F2215
Horn.
F2
315 Right-hand main beam headlamp.
F2
415 Left-hand main beam headlamp.
F275
Left hand lamp mask.
F2
85 Right hand lamp mask.

12 V battery
The presence of this label indicatesthe use of a 12 V lead-acid battery withspecial technology and specification, for which the involvement of a CITROËN dealer or qualified workshop is requiredwhen replacing or disconnecting thebattery.
Failure to observe this recommendation may cause premature wear of thebattery. The battery is located under the bonnet.
To
gain access to it:)
open the bonnet using the interior releaselever, then the exterior safety catch, )
remove the plastic cover on the (+)
terminal,) if necessary, unclip the fusebox to remove
the battery.

Access to the battery



Disconnecting the (+) cable
)Raise the locking tab Dfully to release the cable terminal clamp E
.



Reconnecting the (+) cable
)Position the open clamp Eof the cable on
the positive post
(+) of the battery. )Press ver tically on the clamp E to positionit correctly on the battery. )Lock the clamp by spreading the positioning lug and then lowering the tab D.

Do not apply excessive force on thetab as locking will not be possible if the clamp is not positioned correctly; star tthe procedure again. Procedure
for starting the engine using another battery or charging a discharged battery.

211Practical information

After refitting the battery, the Stop &Start system will only be active after several hours depending on the climaticconditions and the state of charge of the battery (up to about 8 hours).


The Stop & Start battery does not have to be disconnected for charging.
Starting using another
battery


First check that the slave battery has a nominal voltage of 12 V and a capacity at least equal to that of the discharged battery.
Do not try to star t the engine byconnecting a battery charger.
Do not disconnect the (+) terminal when the engine is running.
)Connect the red cable to the positive
terminal (+) of the flat battery A , then to the positive terminal (+) of the slave battery B
.)Connect one end of the green or blackcable to the negative terminal (-) of the slave battery B
(or ear th point on the other
vehicle).)Connect the other end of the green or black cable to the ear th point Con the broken
down vehicle (or on the engine mounting).)Star t the engine of the vehicle with the good battery and leave it running for afew minutes.
) Operate the star ter on the broken down
vehicle and let the engine run
If the engine does not star t straight away, switch off the ignition and wait a few
moments before trying again.) Wait until the engine returns to idle thendisconnect the jump lead cables in the reverse order.
)
Disconnect the battery from the vehicle.)
Follow the instructions for use provided by
the manufacturer of the charger. ) Connect the battery star ting with the negative terminal (-).)
Check that the terminals and connectors
are clean. If they are covered with sulphate (whitish or greenish deposit), remove themand clean them.

Charging the battery using
a battery charger

When your vehicle's battery is discharged,
the engine can be star ted using a slave battery (external or on another vehicle) and jump leadcables.

The batteries contain harmful substances such as sulphuric acid and lead. They must be disposed of in accordancewith regulations and must not, in anycircumstances, be discarded with household
waste. Take used remote control batteries and vehicle batteries to a special collection point.
It is advisable to disconnect the batteryif the vehicle is to be left unused for more than one month.
Do not push the vehicle to star t the engine if you have an electronicgearbox or automatic gearbox.


Protect your eyes and face before
handling the battery. All operations on the battery must becarried out in a well ventilated area and away from naked flames and sourcesof sparks, so as to avoid the risk of explosion or fire.
Do not try to charge a frozen battery; the battery must first be thawed out to avoid the risk of explosion. If the batteryhas been frozen, before charging have it checked by a CITROËN dealer or aqualified workshop who will check that the internal components have not beendamaged and the casing is not cracked,which could cause a leak of toxic and corrosive acid. Do not reverse the polarity and use only
a 12 V charger.
Do not disconnect the terminals whilethe engine is running.
Do not charge the batteries withoutdisconnecting the terminals first.
Wash your hands after wards.








Before disconnecting the battery

Wait 2 minutes after switching off the ignition
before disconnecting the battery.
Close the windows and the doors before
disconnecting the battery.


Following reconnection of the
battery
Following reconnection of the battery, switch on
the ignition and wait 1 minute before star ting topermit initialisation of the electronic systems. However, if problems remain following this
operation, contact a CITROËN dealer or a qualified workshop.
Referring to the corresponding section,you must yourself reinitialise (depending on
version):


- the remote control key,

- the electric blind(s),- ...

213Practical information








Load reduction mode
System which manages the use of certainfunctions according to the level of charge
remaining in the battery.
When the vehicle is being driven, the load
reduction function temporarily deactivates cer tain functions, such as the air conditioning,
the heated rear screen...
The deactivated functions are reactivated
automatically as soon as conditions permit.
System which manages the duration of use of
certain functions to conserve a sufficient level
of charge in the battery.
After the engine has stopped, you canstill use functions such as the audio and
telematics system, windscreen wipers, dipped
beam headlamps, cour tes
y lamps, etc. for a maximum combined duration of about forty minutes.








Energy economy mode
Switching to economy mode

A message then appears in the instrument panel screen indicating that the vehicle has
switched to economy mode and the active
functions are put on standby.
If a telephone call is being made at this time,it will be maintained for around 10 minutes with
the Bluetooth hands-free system of your audio
system.


Exiting economy mode

These functions are reactivated automatically
next time the vehicle is driven.) In order to resume the use of thesefunctions immediately, star t the engine and
let it run:
- for less than ten minutes, to use
the equipment for approximatelyfive minutes,
- for more than ten minutes, to use theequipment for up to approximately
thirty minutes.

Let the engine run for the duration specified toensure that the battery charge is sufficient.
Do not repeatedly and continuously restar t theengine in order to charge the battery.
A flat battery prevents the engine from star ting (refer to the "Battery" section).

215
Practical information




Towing the vehicle
Procedure for having your vehicle towed or for towing another vehicle using a removable
tow
ing eye.
To w i ng your vehicle
To w i ng another vehicle
Access to the tools
The towing eye is installed in the boot under
the floor.
To gain access to it: )open the boot, )remove the towing eye, located in the tool box.

)
On the front bumper, unclip the cover by
pressing at the bottom to disengage thesecuring lugs.) Screw the towing eye in fully.)
Install the towing bar.)
Switch on the hazard warning lamps on the
t
owed vehicle.
) On the rear bumper, unclip the cover bylevering at the left with the point of the
towing eye. ) Screw the towing eye in fully. )
Install the towing bar. )
Switch on the hazard warning lamps on the
t
owed vehicle.

When towing with all four wheels on theground, always use a towing bar.
When towing with only two wheels on the ground, always use professionallifting equipment.
When towing with the engine off, thereis no longer any braking or steeringassistance.

)Place the gear lever in neutral(position N
on the electronic gearbox system or automaticgearbox).Failure to obser ve this special condition could result in damageto certain braking components and the absence of braking assistancethe next time the engine is started.