2013 Citroen DS5 HYBRID4 Electric engine

SituationsConsequences

To apply the electric parking brake:) immobilise the vehicle and switch off the ignition. )
pull the control for at least 5 seconds or until application is complete.)
switch on the ignition and check that the electric parking brake
warning lamps come on.
The application is slower than durin
g normal operation.
To release the electric parking brake:)
switch on the ignition.)pull the control lever and hold it for approximately 3 seconds then release it.
If the braking warning lamp is flashing or if the warning lamps do not come on with the ignition on, these procedures will not work. Place the
vehicle on level ground and have it checked by a CITROËN dealer or a qualified workshop.

an
d possibly

flashing



Display of the message "Parking brake fault" and of the followingwarning lamps:


- Only the automatic application on switching off the engine and automatic release on acceleration functions are available.

- The manual application/release of the electric parking brake and theemergency braking are not available.
and possibly
flashin
g



Display of the message "Battery charge fault".

- You must stop as soon as it is safe to do so. Switch off and
immobilise your vehicle (if necessary, place the a chock under a
wheel).

- Apply the electric parking brake before switching off
the engine.

Repair procedure
)Switch off the ignition.
) Uncoil the white pipe G
fully.)
Unscrew the cap from the white pipe.)
Connect the white pipe to the valve of the
tyre to be repaired.

)Connect the compressor's electric plug to
the vehicle's 12 V socket. )Star t the vehicle and leave the engine running.
Take care, this product is harmful (e.g.ethylene-glycol, colophony...) if swallowed and causes irritation to the eyes.Keep this product out of the reach of children.
Avoid removing any foreign bodieswhich have penetrated into the tyre.
1. Sealing
)Turn the selector Ato the "sealant"position.)Check that the switch B
is in
position "O".

2. Infl ation )
Connect the compressor's electric plug to
the vehicle's 12 V socket.) Star t the vehicle again and leave the engine running.

)Adjust the pressure using the compressor (to inflate: switch B
in position "I"
; to deflate: switch B
in position "O"and press button C), in accordance with the vehicle's
tyre pressure label (located on the left hand
door aperture).
A loss of pressure indicates that the
puncture has not been fully plugged; contact a CITROËN dealer or qualified
workshop for assistance.)Remove and stow the kit.
)Drive at reduced speed (50 mph [80 km/h] max) limiting the distance travelled toapproximately 120 miles (200 km).




As soon as possible, go to a CITROËNdealer or a qualified workshop.You must inform the technician that you have used this kit. After inspection, the technician will advise you on whether the tyre can be repaired or if it must be replaced.
)Turn the selector Ato the "air" position.)Uncoil the black pipe Hfully. )Connect the black pipe to the
valve of the wheel.

205
Practical information

Removing the cartridge
)Stow the black pipe. )Detach the angled base from the white pipe.)Suppor t the compressor ver tically.)Unscrew the car tridge from the bottom.


Beware of discharges of fluid.
The expiry date of the fluid is indicated on the car tridge.
The sealant car tridge is designed for
single use; even if only partly used, itmust be replaced. After use, do not discard the car tridgeinto the environment, take it to an authorised waste disposal site or a CITROËN dealer.
Do not forget to obtain a new sealantcartridge, available from CITROËN dealers or from a qualified workshop.

Checking tyre pressures /
inflating accessories
You can also use the compressor, withoutinjecting any product, to:
- check or adjust the pressure of your tyres,
- inflate other accessories (balls, bicycle
tyres...).

)
Turn the selector Ato the "Air"
position.
) Uncoil the black pipe H
fully.)
Connect the black pipe to the
valve of the wheel or accessory.
If necessary, fit one of the adaptorssupplied with the kit first.
) Connect the compressor's electrical connector to the vehicle's 12 V socket. )
Star t the vehicle and let the engine run. )
Adjust the pressure using the compressor (to inflate: switch B
in position "I"
; to deflate: switch Bin position "O"and press button C ), according to the vehicle's tyrepressure label or the accessory's pressure
label.) Remove the kit then stow it.

Changing a wheel Procedure for changing a faulty wheel for the spare wheel using the tools provided with the vehicle *
.
Th
e tools are installed in the boot under
the floor.
Access to the tools

List of tools *
















Tyre under-infl ation detection

The spare wheel is not fitted with a sensor. The punctured wheel must berepaired by a CITROËN dealer or a
qualified workshop.

Before doing any work on your vehicle,switch off the ignition ( Ready
lamp off)to avoid any risk of injury resulting fromautomatic operation of the engine.











When using lifting equipment (a jack
for example), take care to use the jacking points provided, so as to avoiddamaging the high voltage cables.
All of these tools are specific to your vehicle and can vary according to the level of equipment.
Do not use them for other purposes. 1. Wheelbrace.
For removing the wheel trim and removingthe wheel bolts. 2.Jack with integral handle.
For raising the vehicle.3."Bolt cover" tool.
For removing the bolt protectors (covers)
on alloy wheels.4. Wheel trim remover.
For removing the alloy wheel finishers.
5. Socket for the security bolts (located in the glove box).
For adapting the wheelbrace to the special"security" bolts.
6.Wheel chocks for blocking the vehicle's
wheels.7. Towing eye.
See the "Towing the vehicle" section.8.Extension spanner.
For slackening/tightening the spare wheelcarrier nut. 9. Emergency release control for the electric parking brake.
See the "Electric parking brake" section, "Emergency braking".


*

According to country of sale.

227Practical information
Do not attempt to charge the high voltage battery.
The batteries contain harmful substances such as sulphuric acid and lead. They mustbe disposed of in accordance with regulations and must not, in any circumstances, bediscarded with household waste.
Take used remote control batteries and vehicle batteries to a special collectionpoint.
It is advisable to disconnect the battery if the vehicle is to be left unused for more than one month.


Protect your eyes and face before handling the battery. All operations on the battery must becarried out in a well ventilated area andaway from naked flames and sourcesof sparks, so as to avoid the risk of explosion or fire.
Do not try to charge a frozen battery;the battery must first be thawed out to avoid the risk of explosion. If the batteryhas been frozen, before charging have it checked by a CITROËN dealer or aqualified workshop who will check that the internal components have not beendamaged and the casing is not cracked,which could cause a leak of toxic and corrosive acid. Do not reverse the polarity and use onlya 12 V charger. Do not disconnect the terminals whilethe engine is running. Do not charge the batteries withoutdisconnecting the terminals first.
Wash your hands afterwards.
Do not push the vehicle to star t the engine if the vehicle is fitted with the electronic gearbox.







Before disconnecting the battery

Wait 2 minutes after switching off the ignition
before disconnecting the battery.
Close the windows and the doors before
disconnecting the battery.


Following reconnection of the battery

Following reconnection of the battery, switch on
the ignition and wait 1 minute before star ting to
permit initialisation of the electronic systems.However, if problems remain following this operation, contact a CITROËN dealer or a qualified workshop.
Referring to the corresponding section, you
must yourself reinitialise (depending on
version):


- the remote control key,

- the electric blind(s), - ...

Do not push the vehicle to star tthe engine.

We recommend the use of genuine
CITROËN towbars and their harnesses that have been tested and approved from the design stage of your vehicle,and that the fitting of the towbar is
entrusted to a CITROËN dealer or aqualified workshop.
If the towbar is not fitted by a CITROËN dealer, it is imperative that it isfitted in accordance with the vehiclemanufacturer's instructions.


Driving advice


Distribution of loads
)
Distribute the load in the trailer so that the
heaviest items are as close as possible to
t
he axle and the nose weight approaches the
maximum permitted without exceeding it.
Air density decreases with altitude, thus
reducing engine performance. Above
1 000 metres, the maximum towed load must
be reduced by 10 % for every 1 000 metres of altitude.


Side wind
)
Take into account the increased sensitivity
to side wind.



Cooling

To w i ng a trailer on a slope increases the
temperature of the coolant.
As the
fan is electrically controlled, its cooling capacity is not dependent on the engine speed.)
To lower the engine speed, reduce your speed.
)
If the warning lamp and the STOPwarning lamp come on,stop the vehicle and switch off
the engine as soon as possible.

Braking

To w i ng a trailer increases the braking distance.
To avoid overheating of the brakes on a longmountain type of descent, the use of engine braking is recommended.

Tyres
)Check the tyre pressures of the towingvehicle and of the trailer, obser ving the recommended pressures.



Lighting
)Check the electrical lighting and signalling on the trailer.


The rear parking sensors will be deactivated automatically if a genuine CITROËN towbar is used.



Driving with a trailer places greater demands on the towing vehicle and thedriver must take par ticular care.

The maximum towed load on a long incline depends on the gradient and the ambient
tem
perature.
In all cases, keep a check on the coolant
temperature.

R
efer to the "Technical data" section for detailsof the weights and towed loads which apply toyour vehicle.

239Checks
Opening the bonnet
Opening
)
From inside
: pull the release lever, located
on the left below the dashboard, towards you.
Before doing anything under the bonnet,
switch off the ignition (Ready lamp off) to avoid any risk of injury resulting fromautomatic operation of the engine.


Closing
)
Lower the bonnet and release it at the endof its travel. )
Check that it is latched correctly.


)From the outside: lift the safety catch and
raise the bonnet.
A bonnet strut opens the bonnet and holds itopen.


Never touch, handle or remove the orange "high voltage" cables.

The use of a high pressure jet wash under the bonnet is strictly prohibited,in order to avoid damage to the electriccomponents.