2013 Citroen DS5 HYBRID4 Owner's Manual

215
Practical information
Main beam headlamps (xenonmodel)
) Remove the protective plastic cover by
pulling on the tab. ) Remove the connector with the bulb bypressing on the lug at the bottom.)
Remove the bulb and change it.For reassembly, carry out these operations in reverse order.


The headlamps are fitted with polycarbonate glass with a protectivecoating:)do not clean them using a dry or abrasive cloth, nor with a detergent or solvent product,)
use a sponge and soapy water or apH neutral product,)
when using a high pressure washer on persistent marks, do not keep the lance directed towards thelamps or their edges for too long, so as not to damage their protectivecoating and seals.
Dipped beam headlamps (xenon model)

D1S xenon bulbs must be changedby a CITROËN dealer or a qualifiedworkshop, as there is a risk of electrocution.
It is recommended that the D1S bulbsare changed at the same time when oneof them fails.
Changing a bulb should only be doneafter the headlamp has been switched off for a few minutes (risk of serious burns). )Do not touch the bulb directly withyour fingers, use a lint-free cloth. It is imperative to use only anti-ultraviolet (UV) type bulbs to avoid damaging the headlamp. Always replace a failed bulb with a new bulb with the same type andspecification.

Dipped beam headlamps
(halogen model)
)
Remove the protective plastic cover by
pulling on the tab.
Main beam headlamps
(halogen model)
)Remove the protective plastic cover bypulling on the tab. )Remove the connector with the bulb by pressing on the lug at the bottom.)Remove the bulb and change it.For reassembly, carry out these operations in reverse order.

)Press on the top of the connector then pivot the assembly downwards.)Remove the connector with the bulb. )Remove the bulb and change it.
For reassembly, carry out these operations in
reverse order, but engaging the bottom of thebulb first.

217Practical information
Daytime running lamps / sidelamps
For the replacement of this type of LED lamp
and lighting guides, contact a CITROËN dealer
or a qualified workshop.

A replacement kit for the LEDs is available fromCITROËN dealers.
Direction indicators
Faster flashing of a direction indicator warning lamp (left or right) indicates a failed bulb on that side.
The direction indicator bulb is located below the front lamp.) Turn the bulb holder a quar ter turn and pull
it out. ) Remove the bulb and change it.
For reassembly, carry out these operations in
reverse order.
You can also contact a CITROËN dealer or a
qualified workshop for the replacement of these bulbs.

Front foglamps
)Remove the deflector under the body.)Disconnect the bulb connector.
)Turn the bulb a quarter of a turn, withdraw and change it.
To r e f i t , c a r ry out these operations in reverse order.
To replace these bulbs you may also contact a CITROËN dealer or a qualified workshop.

Integrated direction indicator
side repeaters
You should contact a CITROËN dealer or aqualified workshop for the replacement of these bulbs.
Door mirror spotlamps
You should contact a CITROËN dealer or a
qualified workshop for the replacement of the light emitting diode - LED.

219Practical information
1.Sidelamps(light emitting diodes - LEDs).2.Direction indicators (PY21W amber).3.Reversing lamps (P21W).4. Brake lamps (P21W).5.Foglamps (P21W).
Rear lamps
Direction indicators and brakelamps (on the wings)
) Open the boot then remove the accesscover.)
Disconnect the lamp connector. )
Remove the two lamp fixing nuts.
)
Carefully remove the lamp unit from
outside. The retaining clips unclip
automatically.
) Turn the bulb holder a quarter of a turn andchange the bulb.
For reassembly, carry out these operations in
reverse order.


Changing the light emitting diode-LED lamps

For replacement, contact a CITROËN dealer or qualified workshop.

Reversing lamp (tailgate)
)Open the tailgate.)Unclip the skir t of the lamp.)Remove the access cover and the lamp fixing nut.
) Carefully remove the lamp from theoutside. The retaining clips unclip
automatically.) Turn the bulb holder a quarter of a turn and
replace the bulb.
For reassembly, carry out these operations in reverse order.
Foglamp
Access is by passing a hand under the bumper. )Turn the bulb holder a quar ter of a turn andpull it out. )Change the bulb.
To r e f i t , c a r ry out these operations in reverse order.
You can also contact a CITROËN dealer or a qualified workshop for the replacement of thesebulbs.

221Practical information
Number plate lamps
) Insert a thin screwdriver into the slot in thelens. )
Push it outwards to unclip it. )
Remove the lens.)
Pull the bulb out and change it.


Third brake lamp (light emittingdiodes - LEDs)

Contact a CITROËN dealer or qualified
workshop.

Changing a fuse Procedure for replacing a failed fuse with a new fuse to rectify a failure of the corresponding function.
Th
e fuse extraction tweezer is fitted to the back of the dashboard fusebox cover.
For access to it: )remove the cover completely,)remove the tweezer.

Access to tooling

Before changing a fuse, the cause of the failure
must be identified and rectified. ) Identify the failed fuse by checking thecondition of its filament.


Changing a fuse
Good Failed
)
Use the special tweezer to extract the fuse
from its housing.)
Always replace the failed fuse with a fuse of the same rating.)
Check that the number marked on thefusebox, the rating marked on the fuse and
the following tables all agree.

CITROËN will not accept responsibilityfor the cost incurred in repairing your vehicle or for rectifying malfunctions resulting from the installation of accessories not supplied and notrecommended by CITROËN andnot installed in accordance with its instructions, in par ticular when thecombined consumption of all of the additional equipment connectedexceeds 10 milliamperes.



Installing electricalaccessories

Your vehicle's electrical system isdesigned to operate with standard or optional equipment.
Before installing other electrical equipment or accessories on your vehicle, contact a CITROËN dealer or aqualified workshop.