2013 Citroen C4 PICASSO towing

188
Driving
To deactivate the system, press
this button a
gain; its indicator lamp goes off as well as theassociated indicator in the
instrument panel. In the event of a fault, the warnin
g
lamp flashes then goes off.

Operating fault

Have it checked by a CITROËN dealer or aqualified workshop.
The system is automatically deactivated when towing with a towbar approved by CITROËN.


The system may suffer temporary interference in certain weather conditions (rain, hail...).
In par ticular, driving on a wet surface or moving from a dry area to a wet area can cause false alerts (for example, the presence of a fog of water droplets in the blind spot angle is interpreted as avehicle).
In bad or wintry weather, ensure thatthe sensors are not covered by mud, iceor snow. Take care not to cover the warning zone in the door mirrors or the detectionzones on the front and rear bumpers with adhesive labels or other objects;they may hamper the correct operation of the system. The state o
f the system remains in memory on switching off the ignition.
High pressure jet wash When washing your vehicle, direct the lance at least 30 cm away from the sensors.

201
4
Driving
The system is deactivated automatically:


- on switching off the ignition,

- if the engine stalls,

- if no manoeuvre is star ted within 5 minutes
of selection of the t
ype of manoeuvre,

- after a prolonged stop of the vehicle during a manoeuvre,

- if the road wheel anti-spin regulation (ASR) is triggered,

- if the speed of the vehicle exceeds thestated limit,

- when the driver interrupts movement of the steering wheel,

- if the driver presses the Park Assist control.

- after 4 manoeuvre c
ycles,

- on opening the driver's door,

- if one of the front wheels encounters anobstacle.
The operation indicator lamp goes off in the
instrument panel and a message is displayed
accompanied b
y an audible signal.
The driver should then take back control of thevehicle's steering.


Deactivation


If the system is deactivated during a manoeuvre, the drive should reactivate it manually to repeat the measurement.
The s
ystem is switched off automatically:
- when towing a trailer,
- if the driver's door is opened,
- if the speed of the vehicle is above 42 mph(70 km/h).
To switch the system of for a prolonged period, contact a CITROËN dealer or a qualified workshop.

In the event of a fault with the system,
this warning lamp is displayed in the
instrument panel and a messa
ge appears,
accompanied b
y an audible signal.
Operating faults
In the event of a fault with the power steering, this warning lamp
comes on in the instrument panel accompanied by an aler t message.
Contact a CITROËN dealer or a qualified
workshop.
Switching off

If the lateral distance between your vehicle and the space is too great, the system maynot be able to measure the space.
Anything projecting beyond the envelopeof the vehicle (long or wide load) is not taken into account by the Park Assist system during a manoeuvre.

In bad weather or in winter, ensure thatthe sensors are not covered by road dir t, ice or snow.
In the event of a fault, have the systemchecked by a CITROËN dealer or a qualified workshop.
The indicator lamp
for the function flashes for a few seconds.
If the fault occurs during the use of
the system, the indicator lamp goesoff.

222
Safety











Direction indicators
)Left: lower the lighting stalk passing thepoint of resistance.)Right: raise the lighting stalk passing the point of resistance.
Three fl ashes of the directionindicators
)Press briefly upwards or downwards,
without going beyond the point of resistance; the direction indicators will flash 3 times.









Hazard warning lamps

A visual warning by means of the directionindicators to alert other road users to a vehiclebreakdown, towing or accident.)
Press this button, the direction indicatorsflash.
They can operate with the ignition off.
Automatic operation of
hazard warning lamps
When braking in an emergency, depending on
the deceleration, the hazard warning lampscome on automatically.
The
y switch off automatically the first time youaccelerate. )
You can also switch them off by pressing
the button.





Horn
Audible warning system to alert other road
users to an imminent danger.)Press the central part of the steering
wheel.

Use the horn moderately and only in the following circumstances:


- immediate danger,

- over taking a cyclist or pedestrian

- approaching a location lacking
visibility.

223
6
Safety
This system allows you to make an emergency
or assistance call to the emergency services or
to the dedicated CITROËN service.








Emergency or
assistance call

For more information on the use of this function, refer to the "Audio and telematics"section.












Warning triangle
This safety device should be used in addition to
the hazard warning lamps.
Its presence in the vehicle is mandatory.

A location
for stowing the warning triangle isprovided in the tailgate interior trim.


Placing the triangle in the road
)
Place the triangle behind the vehicle, as
required by the legislation in force in your
country.




Before leaving your vehicle to set up and install the triangle, switch on thehazard warning lamps and put on your high visibility vest.


Refer to the manufacturer's instructions on unfolding and installing supplied withthe triangle.

231
6
Safety
2nd row seat belts







Fastening
)Pull the strap, then inser t the tongue in the buckle.)Check that the seat belt is fastenedcorrectly by pulling the strap.



Unfastening
)Press the red button on the buckle.)Guide the seat belt as it reels in.The rear seats are each
fitted with a seat belt,
three-point anchorages with inertia reel and
force limiter (except for the centre rear seat).
Guide the belt as it reels in and place the
tongue on the magnet at the side anchoragepoint.


2ndrow outer seat belts
(stowing)

232
Safety
2 nd row centre seat belt
The seat belt for the centre rear seat is built into the roof.
Fastening
)Pull the strap and inser t the tongue A
into
the right hand buckle.)Inser t tongue Binto the left hand buckle.)Check that each buckle is correctlyfastened by pulling on the belt webbing.



Unfastening
)
Press the red button in buckle B , then buckle A.)
Guide the seat belt as it reels in and place
the tongue Band then A on the magnet in
the roof anchorage point.


Before any operation of the rear seats,to avoid damage to the seat belts check that there is no slack in the outer belts and secure their tongues on the anchorage points. The centre seat beltmust be fully reeled in.



3rd row seat belts

Fastening
)Detach the seat belt strap from its retainingloop located on the side trim of the boot. )Pull on the strap and inser t the tongue into
the buckle. )Check that the buckle is correctly fastened
b
y pulling on the belt strap.

Unfastening and stowing
)Press the red button in buckle. )Guide the seat belt strap as it reels in.)Secure the strap, flat in the retaining loop.
Ensure that the the seat belts are secured when not in use.

261
7
Practical information
List of tools

* Depending on equipment. All o
f these tools are specific to your vehicle and can vary according to equipment. Do not use them for other purposes.
1.12 V compressor.
Contains a sealant cartridge for the
temporary repair of a tyre and can also be used for adjusting tyre pressures. 2. Chocks *
to immobilise the wheels of thevehicle. 3.
Bolt cover removal tool *
.
For removing the wheel bolt finishers (covers) on alloy wheels.4. Removable towing eye.
See the "Towing the vehicle" section.

270
Practical information
*
Depending on version. The complete tooling
is with the spare wheel.











Changing a wheel Procedure for changing a wheel with a punctured tyre by the spare wheel using the tools provided with the vehicle.
Some of the tools are accessible from inside
th
e boot. The wheel chocks 2as well as thewheelbrace extension 6are stowed under theright hand boot sill.The wheelbrace 1
and the towing eye 7
arestowed under the left hand boot sill.The other tools, the jack 3
and the tool for removing the wheel bolt head finishers for alloy
wheels 4 , are stowed in a box attached to thespare wheel. The assembly is secured under
the vehicle in a carrier. See the "Access to thespare wheel" section).
Access to the vehicle's tools *
2.Wheel chocks for immobilising the vehicle
(except versions with manual gearbox).3.Jack with integral handle.
For raising the vehicle.4. Wheel bolt head cover removal tool.
For removing the wheel bolt head finishers
on alloy wheels.
5. Socket for the security bolts (stowed in the glove box).
For adapting the wheelbrace to the specialsecurity bolts.
6.Wheelbrace extension.
For unscrewing/tightening the spare wheelcarrier drive.
7. To w i ng eye.


Wheel with trim
When removing the wheel
, detach the trimfirst using the wheelbrace 1
pulling at the valvepassage hole.
When refitting the wheel
, refit the trimstarting by placing its notch facing the valve
and press around its edge with the palm of your hand.



List of tools *

All of these tools are specific to your vehicle
and can var
y according to equipment. Do not use them for other purposes. 1.Wheelbrace.
For removing the wheel trim and the wheelfixing bolts.